Hyundai 924052S100, 924062S100

Contents

Rear Bumper Reflector Instruction Manual

For Hyundai Tucson GL L SE GLS Limited (2010-2015)

Model Numbers: 924052S100 (Left), 924062S100 (Right)

1. Product Information

This manual provides instructions for the installation and maintenance of the Rear Bumper Reflector designed for specific Hyundai Tucson models.

Product Name: Rear Bumper Reflector
Model: BFF4-51-5L0AF
Batch/Serial Number: RA07637A
Item Type: Reflective Strips
Origin: Mainland China

2. Manufacturer & EU Representative Information

Manufacturer:

Guangzhou Kuxiong Shi Trading Co., Ltd
No. 503, Building 3, Courtyard 2, Zhongquantang Road, Industrial Avenue, Haizhu District, Guangzhou City
Phone: 86-18814180059
Email: tingting26181@outlook.com

EU Authorized Representative:

Sea&Mew Consulting GmbH
Mittenhuber Straße 4, 92318 Neumarkt
Phone: +4915224685061
Email: Compliance.EU@outlook.com

3. Compliance Information

This product complies with relevant European Union directives and regulations, indicated by the CE marking.

CE

4. Safety & Warnings

  • Warning: To prevent pinching and burns, ensure the vehicle's exhaust pipe has cooled down completely before proceeding with the installation.
  • Always wear appropriate personal protective equipment (PPE) during installation.
  • Ensure the vehicle is securely supported if lifting is required.

5. Setup and Installation

This rear bumper reflector is compatible with Hyundai Tucson GL L SE GLS Limited models from 2010 to 2015. Installation methods may vary based on the original reflector type.

General Installation Overview:

Rear bumper reflector installed on a Hyundai Tucson, highlighting the placement area.
Image: Rear bumper reflector installed on a Hyundai Tucson, with a green dashed box indicating the installation area.
Two rear bumper reflectors, one for the left side and one for the right side.
Image: A pair of red rear bumper reflectors, illustrating the left and right side components.

Installation Method 1: Snap-on Type

  1. Carefully remove the old reflector from its housing using a plastic pry bar to avoid damaging the surrounding bumper.
  2. Align the new reflector with the snap-on position on the bumper.
  3. Press the new reflector firmly into place until you hear a "click" sound, ensuring it is securely locked.
Close-up of a mounting pin on the back of the reflector.
Image: Detailed shot of a white plastic mounting pin on the rear side of the reflector, typical for snap-on installation.

Installation Method 2: Bolted Type

  1. Lift the vehicle safely using a jack and jack stands to gain access to the inside of the bumper.
  2. Reach inside the bumper to locate and remove the bolts securing the old reflector.
  3. Position the new reflector and secure it with the appropriate bolts.
  4. Tighten the bolts with appropriate force to ensure the reflector is secure without damaging the parts.
  5. Carefully lower the vehicle.

6. Operating and Use

The rear bumper reflector functions passively by reflecting light from other vehicles, enhancing visibility and safety, especially in low-light conditions. No active operation is required after proper installation.

7. Maintenance

  • Regularly inspect the reflector for dirt, grime, or damage.
  • Clean the reflector surface with a soft cloth and mild automotive cleaning solution to ensure optimal reflectivity. Avoid abrasive cleaners or harsh chemicals.
  • If the reflector becomes cracked, broken, or loses its reflective properties, replace it promptly to maintain vehicle safety.

8. Troubleshooting

  • Reflector is loose after installation: Re-check the mounting points. For snap-on types, ensure a "click" sound was heard. For bolted types, ensure bolts are tightened correctly.
  • Reflector appears dull or scratched: Clean the surface thoroughly. If dullness persists or scratches are deep, replacement may be necessary.
  • Difficulty installing: Ensure you have the correct reflector for your vehicle's side (left/right) and model year. Refer to the specific installation method (snap-on or bolted) and ensure all old components are fully removed.

9. Specifications

Part Numbers: Left: 924052S100, Right: 924062S100
Compatibility: Hyundai Tucson GL L SE GLS Limited (2010, 2011, 2012, 2013, 2014, 2015)
Material: Plastic (Reflective)
Color: Red
Approximate Dimensions (Single Reflector): Length: 29 cm (11.42 inches)
Approximate Product Weight (Single Reflector): 0.146 kg
Approximate Package Dimensions: Length: 30 cm, Width: 10 cm, Height: 6 cm
Rear bumper reflector with a length measurement of 29cm (11.42 inches).
Image: A single red rear bumper reflector with an arrow indicating its length as 29cm (11.42 inches).

10. User Tips

  • When removing the old reflector, use a plastic trim removal tool to prevent scratching the paint or damaging the bumper.
  • Before fully securing the new reflector, test its fit to ensure proper alignment.
  • Consider replacing both left and right reflectors simultaneously for a uniform appearance and consistent reflectivity.

11. Warranty and Support

For warranty information or technical support, please contact the manufacturer or your point of purchase. Keep your purchase receipt and product batch/serial number (RA07637A) for any warranty claims.

You can also refer to the original user manual PDF for additional details: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.