1. Product Overview
The CENJITION Universal High-Flow Angled Air Filter is designed to improve engine horsepower and throttle response by increasing airflow. It features a 45-degree bent neck for flexible installation and a multi-layer cotton gauze filter media that is washable and reusable. This filter is suitable for a wide range of motorcycles, scooters, ATVs, and pit dirt bikes.
2. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Universal High-Flow Angled Air Filter (45° Bent Neck) |
| Brand | CENJITION |
| Inlet Diameter (Selectable) | 35mm, 38mm, 39mm, 42mm, 48mm, 50mm, 52mm |
| Neck Angle | 45° bent rubber neck |
| Filter Material | Multi-layer oil-impregnated cotton gauze + stainless steel mesh |
| Housing Material | Chrome-plated aluminum alloy (top/bottom rings) |
| Clamp | Stainless steel worm-drive hose clamp (included) |
| Color | Chrome (housing) + Black (rubber neck/filter mesh) |
| Item Type | Air Filters & Systems |
| Item Weight | 120g |
| Item Dimensions (approx.) | Length: 10cm, Width: 7.5cm, Height: 5cm |
| Service Life | 20,000-30,000 km (or 1-2 years) - cleanable/reusable |
| Origin | Mainland China |
2.1. Material & EU Regulatory Compliance
- Filter Media: Multi-layer oil-impregnated cotton gauze (high flow, high dust capacity) + stainless steel mesh (support).
- Neck: High-temperature resistant EPDM rubber (heat-resistant up to 150°C).
- Housing: Chrome-plated aluminum alloy (lightweight, corrosion-resistant).
- Clamp: Stainless steel (304 grade) - rustproof, durable.
- REACH (EC 1907/2006): Free from SVHCs (Substances of Very High Concern) above 0.1% w/w; no restricted substances listed in Annex XIV.
- RoHS 2 (2011/65/EU): Free from lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium (Cr6+), PBBs and PBDEs.
- General Product Safety Directive (2001/95/EC): Meets EU safety standards for automotive intake components; non-toxic, heat-resistant materials; no sharp edges.
2.2. Product Features
- High-Flow Design: Multi-layer cotton gauze media increases airflow by up to 30% vs. stock paper filters, improving engine horsepower and throttle response.
- 45° Angled Neck: Flexible bent rubber neck allows for flexible installation in tight engine bays and adapts to various carburetor/intake manifold angles.
- Washable & Reusable: Filter media can be cleaned and re-oiled for repeated use, reducing replacement costs and environmental waste.
- Heat-Resistant Rubber Neck: EPDM rubber resists engine bay heat (up to 150°C) and oil contamination, preventing cracking/drying.
- Corrosion-Resistant Housing: Chrome-plated aluminum alloy resists rust and oxidation, enhancing engine bay appearance.
- Secure Clamping: Included stainless steel worm-drive clamp ensures a tight, leak-proof seal on the intake tube/carburetor.
- High Dust Capacity: Cotton gauze media traps fine dust particles without restricting airflow, protecting the engine from abrasive wear.
2.3. Applications
Primary Use: Performance intake for motorcycles, scooters & small engines.
- Motorcycle carburetors (4-stroke/2-stroke)
- Scooter intake manifolds
- ATV/UTV air intake systems
- Small engines (Lawn mowers, generators, go-karts, mini bikes)
Secondary Uses:
- Automotive: Modified car intake systems (carbureted engines, small-displacement)
- Marine: Small outboard motors, jet ski intake systems
Not Suitable For:
- Fuel-injected engines without proper ECU tuning (risk of lean condition/engine damage).
- High-temperature environments (>150°C, e.g., near exhaust headers/turbo manifolds).
- Wet environments (water ingestion risk - do not use in rain/submersion).
- Use without air filter oil (reduces dust filtration efficiency; engine wear risk).
- Road-legal vehicles in EU countries (non-original replacement may violate emissions regulations - check local laws).
3. Setup and Installation
- Size Matching: Select the filter with an inlet diameter that matches your carburetor/intake tube outer diameter (±1mm for optimal fit).
- Prep: Loosen the stainless steel clamp and slide it onto the filter's rubber neck.
- Mounting:
- Slide the filter neck onto the carburetor/intake tube, ensuring full seating with no gaps.
- Position the 45° angle for optimal airflow and clearance. Avoid contact with hot engine parts.
- Tighten the worm-drive clamp with a screwdriver. Do not over-tighten (risk of rubber neck cracking).
- Check Clearance: Ensure the filter does not touch hot components (exhaust, engine) or moving parts (cables, levers) to prevent melting or tearing.
4. Maintenance
4.1. Cleaning & Re-Oiling Procedure
- Removal: Loosen the clamp and remove the filter from the carburetor/intake.
- Cleaning:
- Tap the filter gently to remove loose dust.
- Rinse with warm water and mild detergent (or a dedicated air filter cleaner). Do not use compressed air as it can damage the filter media.
- Rinse thoroughly until water runs clear.
- Squeeze out excess water (do not wring) and air-dry completely (12-24 hours) away from heat/sunlight.
- Re-Oiling:
- Apply a small amount of dedicated air filter oil evenly to the cotton gauze media. Avoid over-oiling, as excess oil may foul spark plugs.
- Let the oil soak in for 10-15 minutes.
- Wipe off any excess oil from the housing/neck.
- Reinstallation: Reinstall the filter following the steps in Section 3. Setup and Installation. Check for secure fit and proper clearance.
5. Troubleshooting
If you experience issues after installing the air filter, consider the following:
- Reduced Engine Performance: Ensure the correct inlet diameter was chosen for your carburetor. Incorrect sizing can lead to air leaks or insufficient airflow.
- Engine Damage/Lean Condition: This filter is not suitable for fuel-injected engines without proper ECU tuning. Using it on such engines without tuning can cause a lean air/fuel mixture, leading to overheating or engine damage.
- Poor Filtration: Always use proper air filter oil. Operating the filter dry significantly reduces its dust filtration efficiency and can lead to premature engine wear.
- Water Ingestion: Avoid using the filter in wet or rainy conditions, or in situations where it might be submerged. Water ingestion can cause hydrolock and severe engine damage.
- Filter Deterioration: Ensure the filter is not in contact with hot engine components or moving parts, which can cause melting, tearing, or premature wear.
- Carburetor Issues: Some users have noted that installing a new air filter can sometimes reveal pre-existing carburetor issues, such as leaks. Inspect your carburetor if new issues arise.
6. Safety Warnings
- Fire & Burn Hazard: KEEP AWAY FROM OPEN FLAMES, SPARKS, AND HOT ENGINE PARTS (>150°C). The oil-impregnated filter media is flammable, and the rubber neck may melt and cause fire. Do not install near exhaust headers, turbo manifolds, or other hot engine components.
- Engine Damage Risk:
- Do not use without proper air filter oil. Reduced filtration causes engine abrasion and premature wear.
- Do not use on fuel-injected engines without ECU tuning. Lean air/fuel mixture may cause overheating, detonation, or engine failure.
- Do not use in wet/rainy conditions. Water ingestion causes hydrolock (engine seizure).
- Choking Hazard: KEEP OUT OF REACH OF CHILDREN AND PETS. Small parts (clamp, filter fragments) pose a suffocation risk if swallowed.
- Material Safety:
- Avoid skin contact with air filter oil. Wear gloves and wash hands with soap and water after use.
- Do not ingest oil/filter media. Seek medical advice if swallowed.
7. User Tips
- Verify Fitment: Always double-check the inlet diameter against your carburetor's outer diameter. A precise fit (within ±1mm) is crucial for secure installation and optimal performance.
- Secure Clamping: Ensure the clamp is tightened sufficiently to prevent air leaks, but avoid excessive force to prevent cracking the rubber neck.
- Pre-Installation Check: Before installing, inspect the filter for any damage or manufacturing defects.
- Revealing Carburetor Issues: Be aware that installing a new, efficient air filter might highlight existing issues with your carburetor, such as leaks, due to changes in airflow dynamics.
- Protective Film: Some filters may come with a protective film or tape. Remove it carefully before installation.
8. Disposal
- Dispose of worn or damaged filters as mixed waste in accordance with the EU Waste Framework Directive (2008/98/EC) and local waste management regulations.
- Separate for Recycling:
- Stainless steel clamp/mesh: Metal recycling
- Aluminum housing: Aluminum recycling
- Rubber neck/EPDM: Rubber recycling
- Cotton gauze: Textile waste (dispose as non-hazardous solid waste)
- Do not incinerate oil-impregnated media as it releases toxic fumes. Do not landfill randomly or discard into water sources. Recycle to reduce environmental impact.
9. Warranty and Support
For specific warranty details, return policies, or further support, please refer to the seller's terms and conditions at the point of purchase. A detailed user manual in PDF format is also available for download: View User Manual (PDF).