1. Introduction
The CPVAN Solar Strobe Siren is a versatile security device featuring a built-in battery charged by solar power. It supports both wireless and wired control signals, offering flexible installation without the need for extensive cabling. This device functions either as a siren when connected to an alarm control panel or as a local alarm host when paired with compatible wireless accessories.
Equipped with infrared sensing and low power consumption ICs, this compact and novel device is designed for various applications, including villas, communities, shops, factories, schools, and banks. It boasts features such as long standby time, anti-EMI, anti-false alarm, and IP65 water resistance, making it suitable for outdoor conditions.
2. Features
- 20x wireless defense zones, 2x wired defense zones.
- Supports up to 5x remote controllers.
- Tamper alarm function.
- Acoustic and light alarm with up to 100dB sound level and dazzling strobe.
- Wireless coding for easy addition of new accessories.
- One-button operation: Arm, Home Arm, SOS, Disarm.
- Solar power charging supported (24mA under 2000LUX condition).
- Memory for paired accessories against power outage.
- High capacity lithium battery built-in.
- Waterproof design with IP65 protection.
3. Technical Specifications
| Parameter | Value |
|---|---|
| External Power Input | DC5V/1A |
| Solar Panel Output | 5.0V |
| Standby Current | < 1 mA |
| Alarm Current | < 150mA |
| Sound Level | >100dB |
| Wireless Frequency | 433MHz |
| Wireless Reception Range | >100m (open space) |
| Water Resistance | IP65 |
| Wireless Coding | EV1527/2262 supported |
| Backup Battery | 3.7V 1000mA Lithium battery |
| Working Temperature | -20°C - 55°C |
| Working Humidity | 40%-80% (no condensing) |
| Form Factor (Dimensions) | 164.3 × 124.3 × 59mm |
4. Setup and Installation
4.1. Initialization
Plug the power adapter into an outlet. Before flipping the power switch on the bottom of the siren, ensure it is connected. The built-in buzzer will sound twice, and the indicator will flash twice, confirming initialization.
4.2. Connection for Wired Zones
- CN1 for wired zone 1: Connect ZO to GND.
- CN1 for wired zone 2: Connect Z1 to GND.
Refer to the diagram below for wired zone connections:
Z1 Z0 GND +5V
4.3. Physical Installation
- The siren is recommended to be installed at the physical center of your house or premises to ensure optimal reception from all wireless detectors.
- Screw the mounting bracket into the wall using the provided screws and anchors, with the ears positioned at the top.
- Attach the siren to the mounting plate by aligning it and pulling it downwards to secure it.
For a visual guide, refer to the "Installation operation" diagram in the full user manual PDF, which shows steps to fix the mounting bracket and hang the alarm siren.
5. Operation
5.1. Pairing a Remote Controller
- Press and hold the SET button until the siren sounds and flashes once.
- Release the button. The siren will flash quickly, indicating it's in pairing mode.
- Press any button on the remote control to emit a signal. The siren will sound twice if the signal is learned successfully.
- To pair additional remote controllers, repeat step 3.
- The siren will exit pairing mode if no signal is received within 10 seconds.
5.2. Pairing a Wireless Detector
- Press and hold the SET button until the siren sounds and flashes twice.
- Release the button. The siren will flash quickly, indicating it's in pairing mode.
- Trigger the wireless detector to emit a signal. The siren will sound twice if the signal is learned successfully.
- To pair additional detectors, trigger the next detector.
- The siren will exit pairing mode if no signal is received within 10 seconds.
5.3. Working as a Wireless Siren (Connecting to an Alarm Control Panel)
- To set this device as a wireless siren, press and hold the SET button until the siren sounds and flashes 3 times.
- Release the button. The siren will flash quickly, entering pairing mode.
- Trigger your alarm control panel to emit a signal. The siren will sound twice if the signal is learned successfully.
5.4. Deleting All Accessories
Press and hold the SET button until the siren sounds and flashes 4 times. Release the button. The siren will sound twice, indicating that all remote controllers and detectors have been deleted.
5.5. Siren Status
- Armed status: All paired accessories can trigger the siren.
- Disarmed status: Only accessories configured in the SOS zone can trigger the siren.
- Alarm status: The strobe siren goes off and exits automatically after the preset siren duration (if no manual operation).
5.6. Remote Controller Functions
The remote controller allows you to operate the siren remotely:
- Away Arm: Press the lock button to arm when you're outside your home.
- Disarm: Press the unlock button to disarm.
- Stay Arm: Press the home button to arm when you're at home.
- SOS: Press the SOS button to activate the strobe siren immediately.
6. Jumper Settings
The siren's behavior can be customized using jumper settings. Ensure to power cycle the device after making any changes for them to take effect.
6.1. Alarm Tone Selection
- Police Tone: No jumper on JP2 and JP3.
- Fire Alarm Tone: Jumper on JP2.
- Ambulance Tone: Jumper on JP3.
6.2. Siren Duration Selection
- 5 minutes: No jumper on JP1.
- 1 minute: Jumper on JP1 (Pin1 and Pin2).
- 3 minutes: Jumper on JP1 (Pin2 and Pin3).
6.3. Infrared Setting
- Enable Infrared: Jumper on JP5.
- Disable Infrared: No jumper on JP5.
6.4. Siren Mode Selection
- Acoustic and Light Alarm: Jumper on JP4.
- Light Only: No jumper on JP4.
Note: All selection settings will only take effect after a power cycle of the device.
For detailed diagrams of the jumper settings (JP1, JP2, JP3, JP4, JP5), please refer to the 'JUMPER SETTING' section in the full user manual PDF.
7. User Tips
- For optimal solar charging, ensure the solar panel is exposed to direct sunlight for several hours daily.
- Regularly test the siren and connected sensors to ensure proper functionality.
- When pairing new accessories, ensure they are compatible with EV1527/2262 wireless coding.
8. Troubleshooting
8.1. Siren Not Responding
- Check if the siren is powered on and the battery is charged.
- Ensure the siren is within the wireless reception range of the alarm control panel or detectors.
- Verify that accessories are correctly paired. If not, try re-pairing them.
- Perform a power cycle (turn off, then on) after checking connections and settings.
8.2. False Alarms
- Ensure detectors are installed correctly and not triggered by pets or environmental factors.
- Check for strong electromagnetic interference (EMI) near the siren or detectors.
- If using infrared, ensure it's not being triggered by unintended movement.
8.3. Low Sound/Light Output
- Check the battery level; a low battery might affect performance.
- Ensure the siren's speaker and strobe light are not obstructed.
9. Maintenance
- Keep the solar panel clean from dust and debris to ensure efficient charging.
- Periodically check the siren for any physical damage, especially after severe weather conditions.
- Ensure the mounting is secure and the siren is not loose.
- Avoid using harsh chemicals for cleaning; a soft, damp cloth is sufficient.
10. Warranty and Support
10.1. Warranty Information
This product comes with a one-year warranty. Please retain your purchase receipt and the warranty card for any warranty service requests.
Warranty Exclusions:
- Damages caused by misuse are not covered.
- Damages resulting from unauthorized dismantling, repairing, or refurbishing are not covered.
- Damages caused by acts of God are not covered.
Users are responsible for any consequential damages in these regards. Always refer to the user manual before use.
For after-sales service, please contact your seller with the product name, model number, and a description of the issue.
A digital version of this user manual is available for download: User Manual (PDF)
11. Frequently Asked Questions (FAQ)
- Q: What are the dimensions of the siren?
- A: The siren's dimensions (Form Factor) are 164.3 × 124.3 × 59mm.
- Q: Is the siren waterproof?
- A: Yes, the siren has an IP65 water resistance rating, making it suitable for outdoor use.
- Q: How is the siren powered?
- A: The siren is primarily powered by a built-in rechargeable 3.7V 1000mA lithium battery, which is charged via a solar panel. It also supports an external DC5V/1A power input.
12. Product Video Overview
Watch this video for an unboxing and overview of the CPVAN Wireless Outdoor Solar Siren.
Video: Unboxing and initial look at the CPVAN Solar Strobe Siren.
13. Wide Applications
The CPVAN Wireless Outdoor Solar Siren is suitable for a variety of environments, including:
- Villa Gardens
- Orchards
- Hotels
- Warehouses
- Communities
- Shops
- Factories
- Schools
- Banks