1. Introduction
Thank you for choosing the HEGEHE USB 5V RGB LED Neon Strip Light. This flexible, waterproof LED strip is designed for versatile indoor and outdoor decorative lighting. It features RGB color changing capabilities, dimming functions, and is controlled via a 24-key infrared remote. This manual provides essential information for safe installation, operation, and maintenance of your neon strip light.
Figure 1: USB 5V RGB Neon Strip Light Kit showing the coiled strip, USB controller, and remote.
2. Safety Instructions
Please read all safety instructions carefully before installation and use.
- The power cord and USB controller are designed for use in dry locations only. Ensure they are not exposed to moisture or water.
- Do not modify the product in any way unless under the direct guidance of a qualified professional electrician. Unauthorized modifications can lead to hazards and will void any implied support.
- HEGEHE is not responsible for any damage or injury caused by modified products or improper installation.
- Ensure the power source is a stable DC 5V USB port. Using an incorrect voltage may damage the product.
- Do not stare directly into the LED lights for extended periods, as this may cause eye strain.
3. Package Contents
Please check the package to ensure all items are present:
- 1 x HEGEHE RGB LED Neon Strip Light (selected length: 1m, 2m, 3m, 4m, or 5m)
- 1 x USB Controller
- 1 x 24-Key IR Remote Control (battery not included for remote)
- 1 x Roll of Double-sided Tape
4. Setup and Installation
- Prepare the Surface: Ensure the installation surface is clean, dry, and smooth for optimal adhesion of the double-sided tape.
- Measure and Cut (Optional): If a shorter length is desired, the neon strip can be cut. Locate the designated cutting marks on the strip (typically every 5.5cm). The shortest possible cut size is 2.5cm. Always cut only at these marked intervals to avoid damaging the circuit.
- Apply the Strip: Carefully peel the backing from the double-sided tape and firmly press the LED neon strip onto your desired surface.
- Connect the Controller: Connect the end of the LED neon strip to the USB controller. Ensure the connectors are aligned correctly.
- Power On: Plug the USB connector of the controller into any standard DC 5V USB power source (e.g., USB wall adapter, power bank, computer USB port).
Figure 2: Features include RGB, Remote Control, Dimming, Cutting, and Double-Sided Tape. Strip dimensions are 6mm width and 12mm height.
Figure 3: Cutting size is 5.5cm (shortest 2.5cm). Includes double-sided tape for installation. The LED strip is IP67 waterproof.
5. Operating Instructions
Once connected to a 5V USB power source, use the provided 24-key IR remote control to operate your neon strip light.
5.1 Remote Control Functions
- ON/OFF: Power the strip light on or off.
- R, G, B, W: Select Red, Green, Blue, or White static colors.
- Color Buttons: Choose from 12 additional preset static colors.
- Brightness Adjustment: Use the up/down arrow buttons to adjust brightness from 0% to 100%.
- FLASH: Cycles through colors quickly.
- STROBE: Flashes a single color.
- FADE: Smoothly fades through different colors.
- SMOOTH: Gradually changes between colors.
Figure 4: The 24-key remote control allows 0-100% brightness adjustment and various color/mode selections.
5.2 Product Demonstration Video
Video 1: Demonstration of the LED neon strip light's color changing capabilities and remote control functions.
6. Maintenance
- Cleaning: To clean the LED neon strip, gently wipe it with a soft, dry or slightly damp cloth. Do not use abrasive cleaners or harsh chemicals. Ensure the power is off and the USB controller is dry before cleaning.
- Storage: If storing the strip for an extended period, ensure it is clean and dry. Coil it loosely to prevent damage to the internal wiring.
- Remote Control: Replace the remote control battery (CR2025, not included) when its range decreases or it stops responding.
7. Troubleshooting
- Light does not turn on:
- Check if the USB power source is active and providing 5V.
- Ensure all connections between the strip, controller, and USB port are secure.
- Verify the remote control battery is functional and correctly inserted.
- Point the remote directly at the IR receiver on the USB controller.
- Remote control not responding:
- Replace the remote control battery.
- Ensure there are no obstructions between the remote and the IR receiver.
- Colors are incorrect or inconsistent:
- Try turning the strip off and on again.
- Ensure the strip is not damaged, especially if it has been bent sharply.
8. Specifications
| Feature | Detail |
|---|---|
| Brand Name | HEGEHE |
| Model Number | USB 5V RGB Neon Strip light |
| Type | Neon LED Strip Light |
| Working Input Voltage | DC 5V (USB) |
| Power Source | DC |
| LEDs Number/Meter | 108 LEDs/M |
| LED Chip Brand | Epistar |
| Emitted Colour | RGB (Color Changeable) |
| Waterproof Grade | IP67 Waterproof (LED strip only) |
| Strip Dimensions | 6mm (Width) x 12mm (Height) |
| Average Life | 50,000 hours |
| Working Temperature | -20°C to 50°C |
| Certification | CE, RoHS, UL |
| Is Smart Device | No |
| Is Batteries Included | No (for strip, remote requires battery) |
| Available Lengths | 1m, 2m, 3m, 4m, 5m |
| Cutting Capability | Yes, at designated marks (every 5.5cm, shortest 2.5cm) |
Figure 5: The LED neon strip is available in 1m, 2m, 3m, 4m, and 5m lengths.
9. User Tips
- Custom Lengths: The LED strip can be cut to your desired length at marked intervals, offering great flexibility for custom installations. Always ensure cuts are made precisely on the designated marks.
- Power Source: For optimal performance, use a reliable 5V USB power adapter with sufficient current output, especially for longer strip lengths.
10. Warranty and Support
For any product-related inquiries, technical support, or warranty claims, please contact the seller directly through your purchase platform. Please have your order number ready for faster assistance.