JHao Xin G38 LED

Contents

User Manual: LED Headlight DRL and Chip Ballast Module

For BMW 5 Series G30 (2018-2020)

Model: G38 LED | Brand: JHao Xin

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new LED DRL Light Strips and Chip Ballast Module, designed specifically for BMW 5 Series G30 (2018-2020) headlights. This product is intended to replace original components that may have yellowed or failed, restoring optimal illumination and appearance.

The product is available as a single left headlight component, a single right headlight component, or a pair of headlights. When distinguishing between left and right, consider sitting in the driver's seat: the left hand corresponds to the left side, and the right hand to the right side of the vehicle.

2. Safety Warnings

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Important: This is a highly specialized operation. Be sure to find a professional installer. Beginners should not attempt to install it.

3. Setup and Installation

The installation of these LED DRL and Chip Ballast Modules requires careful handling and specialized knowledge. It is strongly recommended that installation be performed by a professional.

3.1 General Installation Steps (Headlight Disassembly)

  1. Disassemble the car headlights from the vehicle.
  2. Heat the headlights to 90°C-150°C. Note that different adhesives may require different heating temperatures.
  3. After heating, carefully apply a headlight solution to separate the lens from the rear housing. Remove the original components (DRL strips and chip ballast module).
  4. Our product is a replacement part. Install the new DRL strips and chip ballast module into the headlight assembly.
  5. Assemble the headlight using appropriate sealant to ensure a watertight seal.

3.2 Chip Replacement Method

  1. Pry open the original chip with a screwdriver. If the original chip has fixing screws, remove them first.
  2. After removing the original chip, you will observe traces of thermally conductive silicone. Apply imported silicone evenly to the back of the new product, following the original traces. Ensure the LED lamp beads are coated with thermally conductive silicone underneath.
  3. Position the new chip in the original location. Press down to flatten it and allow it to bind securely.
  4. No programming is required for the new chip.

NOTE: This product must be installed using thermally conductive silicone. This is the only way to ensure the longevity of the product.

3.3 Visual Installation Guide

The following video demonstrates the flexibility and illumination of the DRL strips, which can aid in understanding the handling of the components during installation.

Video: Demonstration of DRL strip flexibility and illumination, showing the product components.

Below are images of the product components and their appearance:

Product components with headlight comparison
Product components (DRL strips, chip) with a comparison to an original headlight.
DRL strips and chip on dark background
DRL strips and chip on a dark background, showing their individual forms.
DRL strips arranged circularly with chip
DRL strips arranged in a circular pattern with the chip in the center.
DRL strips and chip showing shape
DRL strips and chip, highlighting the specific shape of the strips.
DRL strips and chip, alternative angle
DRL strips and chip from an alternative angle.
Two sets of DRL strips and chips
Two complete sets of DRL strips and chips, as they might be packaged for a pair.

4. Operating Instructions

Once correctly installed, the LED DRL Light Strips and Chip Ballast Module operate automatically as part of your vehicle's existing headlight system. They function as Daytime Running Lights (DRL) and contribute to the overall illumination of your headlights. No manual operation is required for these components after installation.

5. Maintenance

The primary maintenance consideration for this product is during installation. Ensuring the correct application of thermally conductive silicone to the chip is crucial for its longevity and performance. Once installed and sealed within the headlight assembly, these components are designed to be maintenance-free under normal operating conditions.

Regularly inspect your headlights for any signs of moisture ingress or damage to the outer lens, which could affect the internal components. Address any issues promptly to prevent damage to the DRLs and chip ballast module.

6. Troubleshooting

6.1 Yellowing of Car Lights

The yellowing of car lights is primarily caused by the DRL and chips burning for extended periods. The probability of DRL damage is approximately 80%, while the chance of chip damage is around 20%. If yellowing is not severe, you may consider replacing individual accessories. However, for severe yellowing, replacing one complete set (DRL + Chip) is the recommended solution for optimal results.

6.2 Color Aberration

Note: Changing only one side (left or right) separately may cause color aberration. Even if both sides are white, there might be noticeable differences in brightness or hue. For users who are particular about color consistency, it is highly recommended to replace both the left and right DRL + Chip sets at the same time.

6.3 Product Not Functioning After Installation

  • Verify all connections are secure and correctly seated.
  • Ensure thermally conductive silicone was properly applied to the chip during installation. Improper application can lead to overheating and failure.
  • Confirm that the headlight assembly is correctly sealed to prevent moisture or debris from affecting the components.
  • If issues persist, consult a professional automotive electrician or the manufacturer.

7. Specifications

Attribute Value
Product Name Auto Headlight Ballast Chip + DRL
Model Name G38 LED
Brand Name JHao Xin
Item Type Angel Eyes
Luminescence Color Chip - White Light
Applicable Models BMW 5 Series G30 (2018-2020) LED headlights
Origin Mainland China
Package Weight 0.27 kg
Package Dimensions 25cm (L) x 20cm (W) x 7cm (H)

8. User Tips

  • For optimal and consistent light output, especially regarding color, consider replacing both left and right headlight components simultaneously, even if only one side is severely affected.
  • Always ensure proper application of thermally conductive silicone to the chip during installation to prevent premature failure and ensure product longevity.
  • Given the specialized nature of this installation, if you are not experienced with automotive electrical work and headlight disassembly, it is highly recommended to seek assistance from a qualified professional.

9. Warranty and Support

9.1 Manufacturer & EU Representative Information

Manufacturer: Yiwu Xinyu Trading Co., Ltd-Room 503, No. 22, Liuruitang Road, Choujiang Street, Yiwu City, Zhejiang Province. Contact: 512881048@qq.com

EU Authorized Representative: MJCM SARL, 78 avenue des Champs Elysees Bureau 326. Contact: 33+767213611

Importer: Yiwu Xinyu Trading Co., Ltd-Room 503, No. 22, Liuruitang Road, Choujiang Street, Yiwu City, Zhejiang Province. Contact: 512881048@qq.com

9.2 Additional Resources

For further detailed item guides and documents, a user manual in PDF format is available. This document can be referenced for additional information not covered in this manual.

Reference: User Manual (PDF)

© 2023 JHao Xin. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.