1. Introduction
The XH-W3001 is a versatile LED Digital Thermostat Temperature Controller designed for precise temperature regulation. It features an automatic mode, a wide temperature control range, high accuracy, and reverse protection for enhanced safety. Its compact design allows for easy installation in various applications.
2. Key Features
- Automatic mode for simplified operation
- Wide temperature control range
- High temperature control accuracy (0.1 ℃)
- Reverse protection
- Easy installation
3. Product Specifications
| Parameter | Value |
|---|---|
| Product Name | Microcomputer Temperature Controller |
| Product Model | XH-W3001 |
| Power Supply Voltage | 12V / 24V / 110-220V (model dependent) |
| Temperature Measurement Range | -50 ℃ ~ 110 ℃ |
| Temperature Control Range | -50 ℃ ~ 110 ℃ |
| Temperature Control Accuracy | 0.1 ℃ |
| Load Power | 120W (for 12V), 240W (for 24V), 1500W (for 110-220V) |
| Measurement Input | NTC10K waterproof probe (L=1 meter) |
| Output Type | Direct output |
| Output Capacity | Maximum 10A |
| Installation Hole Spacing | 73mm (hole diameter 4mm) |
| Appearance Size | 60mm * 45mm * 31mm |
4. Installation and Wiring
The W3001 controller features a durable 1.8mm thick ABS material shell with side holes for easy installation and fixation.
4.1 Installation Dimensions

4.2 Wiring Diagrams
Ensure the device is powered off before attempting any wiring. Connect the output correctly before powering on.
4.2.1 220V Wiring Method

4.2.2 12V/24V Wiring Method

Important Note for 12V/24V Wiring:
- The 12V/24V W3001 requires a DC power supply, such as a transformer or a 12V/24V output DC power source.
- The W3001 is a direct output device. If the output is not connected to a load, do not power on the device to prevent potential issues from two-level contact of the wires and ignition.
5. Operating Instructions
5.1 Control Panel Overview

5.2 Setting Startup Temperature
- Press the Up button once to display the current startup temperature.
- Press and hold the Up button for approximately 3 seconds until the startup temperature number flashes.
- Use the Up and Down buttons to adjust the desired startup temperature value.
5.3 Setting Stop Temperature
- Press the Down button once to display the current stop temperature.
- Press and hold the Down button for approximately 3 seconds until the stop temperature number flashes.
- Use the Up and Down buttons to adjust the desired stop temperature value.
5.4 Restoring Factory Settings
To restore the device to its factory default settings:
- Ensure the device is powered on.
- Press and hold both the Up and Down buttons simultaneously.
- The digital display will show '888' and then automatically switch to the temperature detection mode, indicating that factory settings have been restored.
6. Maintenance
The XH-W3001 is designed for low maintenance. Keep the device clean and free from dust. Ensure all connections are secure and the NTC probe is not damaged. Avoid exposing the unit to excessive moisture or extreme temperatures outside its operating range.
7. Troubleshooting
7.1 Power Cut-off / Device Not Functioning with High-Power Loads
If the device or connected load experiences a power cut-off, especially with high-power appliances like heaters, check the following:
- Load Capacity: The XH-W3001 has a maximum output capacity of 10A. Ensure that the current drawn by your connected appliance does not exceed this limit.
- Voltage Compatibility: The maximum wattage the controller can handle depends on its voltage version:
- For 12V models, max load is 120W (10A * 12V).
- For 24V models, max load is 240W (10A * 24V).
- For 110-220V models, max load is 1500W (approx. 10A * 150V, or 6.8A at 220V, 13.6A at 110V, but limited to 10A).
- Example: A 700W heater connected to a 12V or 24V version of the controller will draw significantly more than 10A (58.3A at 12V, 29.1A at 24V), causing an overload and potential damage or safety trip. Ensure your load's wattage is appropriate for the controller's voltage and maximum amperage.
- Wiring: Double-check all wiring connections for correctness and security. Loose connections can lead to overheating or intermittent power.
8. User Tips
- Always verify the power supply voltage of your XH-W3001 model (12V, 24V, or 110-220V) before connecting it to a power source or load.
- When connecting a load, calculate the current draw (Amps = Watts / Volts) to ensure it does not exceed the controller's maximum 10A output capacity. Overloading can damage the device.
- For applications requiring higher power, consider using the XH-W3001 to control a relay or solid-state relay (SSR) that can handle the larger current, rather than directly powering the load through the controller.
9. Warranty and Support
For any issues or questions regarding your XH-W3001 Temperature Controller, please contact the seller or manufacturer for support. Keep your purchase records for warranty claims.
10. Additional Resources
A PDF version of the user manual may be available for download. Please check the product page or contact the seller for the link: User manual (PDF)