SPEEDRACING MP-1128A

Contents

SPEEDRACING 61338-94D Fuel Valve Petcock User Manual

Model: MP-1128A

Part Number: 61338-94D

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your SPEEDRACING 61338-94D Fuel Valve Petcock. This fuel valve is designed as a replacement part for Harley FLST, FXST, FLT, and FXD motorcycle models manufactured between 1995 and 2001 (1340cc models). Please read this manual thoroughly before use to ensure safe and efficient operation.

SPEEDRACING 61338-94D Fuel Valve Petcock with two filter tubes
Figure 1: SPEEDRACING 61338-94D Fuel Valve Petcock

2. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord (if applicable) out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture unnecessarily.
  • Handle with care to avoid cuts or injuries.

3. Product Overview

The fuel valve petcock controls the flow of fuel from the tank to the carburetor. It features a rotary handle for selecting fuel modes and includes nylon mesh filter tanks to prevent debris from entering the fuel system.

Detailed view of the fuel valve petcock components including rotary handle, oil outlet, threads nut, main fuel tank filter, and auxiliary fuel tank filter.
Figure 2: Product Details and Components

Key components include:

  • Rotary Handle: For selecting fuel flow positions (ON, OFF, RES).
  • 1/4" 90-degree Left Side Oil Outlet: Connects to the fuel line.
  • 13/16" Threads Nut: Secures the petcock to the fuel tank.
  • Nylon Mesh Filter Tanks: Filters fuel for both main and auxiliary fuel lines.

4. Setup and Installation

Installation of the fuel valve petcock is a direct replacement process. Ensure the motorcycle's fuel tank is empty and disconnected before beginning installation. The petcock mounts in the motorcycle's seating position, with the hose outlet facing in one direction for easy fuel line connection.

General Installation Steps:

  1. Ensure the motorcycle is stable and the fuel tank is drained.
  2. Carefully remove the old fuel petcock, noting the orientation of the fuel lines.
  3. Install the new SPEEDRACING 61338-94D Fuel Valve Petcock, ensuring the 13/16" threads nut is securely tightened.
  4. Connect the fuel lines to the 1/4" 90-degree left side oil outlet. Ensure all connections are tight and free of leaks.
  5. Refill the fuel tank and check for any leaks before starting the engine.
Fuel valve petcock installed on a motorcycle engine.
Figure 3: Petcock Installed on a Motorcycle

For a visual guide on the components and assembly, please refer to the video below:

Video 1: Fuel Valve Petcock Component Overview and Operation

5. Operating Instructions

The fuel valve petcock features a rotary handle with three positions to control fuel flow:

Diagram showing the ON, OFF, and RES positions of the fuel valve petcock.
Figure 4: Fuel Valve Positions
  • ON: Turn the handle to the "ON" position to open the main positive fuel tank and allow fuel to flow out from the long tube. This is the standard operating position.
  • OFF: Turn the handle to the "OFF" position to completely close the fuel tank, stopping all fuel flow. Use this position when the engine is stopped for extended periods or during maintenance.
  • RES (Reserve): Turn the handle to the "RES" position to open the auxiliary fuel tank and allow fuel to flow out from the short tube. Use this position when your main fuel supply is low.

6. Maintenance

Regular maintenance ensures the longevity and proper function of your fuel valve petcock.

  • Regular Inspection: Periodically inspect the petcock for any signs of wear, damage, or fuel leaks.
  • Seal Integrity: Regularly check the O-rings and other rubber seals for degradation, cracking, or hardening. Replace them if they show signs of wear to prevent leaks.
  • Filter Cleaning: The nylon mesh filter tanks can become clogged over time. Periodically remove and clean them to ensure unobstructed fuel flow.
  • Secure Connections: Ensure all connections, including the threads nut and fuel lines, remain tight.

7. Troubleshooting

If you encounter issues with your fuel valve petcock, refer to the following common problems and solutions:

Problem Possible Cause Solution
Difficulty starting engine Air lock phenomenon, insufficient fuel supply. Ensure petcock is in the "ON" position. Check fuel lines for blockages or air bubbles.
Interruption of fuel supply or flame out Clogged fuel filter, low fuel in main tank, petcock in wrong position. Check fuel level. Switch to "RES" if main tank is low. Clean or replace fuel filters.
Gasoline flows into carburetor when engine is stopped Petcock not fully closed, faulty petcock, degraded rubber seals. Ensure petcock is in the "OFF" position. Inspect and replace rubber seals if necessary. If problem persists, replace the petcock.
Fuel leaks from petcock Degraded rubber seals, loose connections, faulty petcock. Tighten all connections. Inspect and replace rubber seals. If the petcock itself is leaking, it may need replacement.
Insufficient fuel flow at high speeds Clogged fuel filter, restricted fuel line, non-compliant flow rate. Clean or replace fuel filters. Check fuel lines for kinks or blockages. Ensure the petcock is suitable for your motorcycle's performance requirements.
Vacuum leaks Improper installation, damaged vacuum line, faulty petcock. Verify correct installation. Inspect vacuum lines for cracks or loose connections. If the petcock is the source, it may need replacement.
Diagram illustrating common problems solved by replacing the fuel valve petcock, such as air lock, difficulty starting, and fuel supply interruption.
Figure 5: Problems Solved by Petcock Replacement

8. Specifications

Feature Detail
Model Name MP-1128A
Part Number 61338-94D
Special Features 61338-94D Fuel Valve Petcock
Brand Name SPEEDRACING
Item Type FUEL TANK (component)
Material Metal, Plastic (High-strength aluminum alloy)
External Testing Certification ISO9001
Color Black
Package Length 14 cm
Package Width 7 cm
Package Height 7 cm
Package Weight 0.262 kg
Diagram showing the dimensions of the fuel valve petcock: 13.6cm total length, 1.6cm filter width, 2.7cm nut width, 6cm body length, 5.7cm body width.
Figure 6: Product Dimensions

9. User Tips

  • Seal Inspection: Pay close attention to the material of the sealing rubber. Some users have reported issues with seals degrading quickly when exposed to gasoline. Regularly inspect these components and replace them with high-quality, fuel-resistant alternatives if necessary to prevent leaks and carburetor issues.
  • Fuel Flow Check: After installation, always test the fuel flow rate, especially at various engine speeds. If you experience insufficient fuel supply, particularly at higher speeds, check for clogged filters or a restricted fuel line.
  • Vacuum System: If your motorcycle uses a vacuum-operated petcock, ensure all vacuum lines are properly connected and free of leaks. Vacuum leaks can lead to improper fuel delivery.
  • Model Compatibility: Always double-check that the petcock model (61338-94D) is compatible with your specific Harley FLST, FXST, FLT, or FXD model and year (1995-2001) before ordering and installation.

10. Warranty & Support

For product support, warranty claims, or further inquiries, please contact the manufacturer or their authorized representative:

Manufacturer Information:

  • Company Name: Zhejiang xuzhong automobile parts co., ltd
  • Full Address: No. 666, jingye road, economic development zone, rui'an city, wenzhou city, zhejiang province, China
  • Email: xz2014express@163.com
  • Telephone: 86-15888266370

EU Authorized Representative:

  • Company Name: SUCCESS COURIER SL
  • Full Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
  • Telephone: 34-910602659

A detailed user manual in PDF format is also available for download. Please refer to the official product page or contact support for the link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.