WESA BZH05

Contents

WESA BZH05 Wall-Embedded AC Electrical Outlet

Instruction Manual

Introduction

Thank you for choosing the WESA BZH05 Wall-Embedded AC Electrical Outlet. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new electrical outlet. Please read these instructions carefully before installation and keep them for future reference.

WESA BZH05 Double Socket

Figure 1: WESA BZH05 Double Socket, showcasing firm shell and quality switch with anti-drop and impact resistance.

Safety Information

WARNING: Electrical installation should only be performed by a qualified electrician in accordance with all local and national electrical codes.

  • Always turn off power at the main circuit breaker before installing or servicing the outlet.
  • Do not install in wet or damp locations.
  • Ensure all wire connections are secure and properly insulated.
  • This product is designed with high-temperature flame-retardant material to prevent fire hazards.
Flame Retardant Material

Figure 2: Illustration of high-temperature flame-retardant material, preventing fire hazards.

Package Contents

Verify that all components are present before beginning installation:

  • WESA BZH05 Electrical Outlet (1-socket or 2-socket, depending on model purchased)
  • Mounting Screws
  • Instruction Manual (this document)

Setup and Installation

  1. Turn off Power: Locate your main circuit breaker panel and turn off the power to the circuit where you will be installing the outlet. Verify power is off using a voltage tester.
  2. Prepare Wiring: Strip approximately 1/2 inch (12-15mm) of insulation from the ends of the electrical wires (Live and Neutral).
  3. Connect Wires: Refer to the appropriate wiring diagram below for your specific socket type (1-socket or 2-socket).
    • Connect the Live (L) wire to the terminal marked 'L'.
    • Connect the Neutral (N) wire to the terminal marked 'N'.
    • This model is non-grounding.
  4. Mount the Outlet: Carefully push the wired outlet into the wall box. Secure it with the provided mounting screws. Ensure the outlet is flush with the wall surface.
  5. Restore Power: Once the installation is complete and secure, turn the power back on at the main circuit breaker.

Dimensions

Socket Dimensions

Figure 3: Dimensional drawing for 1-socket and 2-socket versions. 1-Socket: 83x58x39mm (3.26x2.28x1.53in). 2-Socket: 105x51x35mm (4.13x2.00x1.38in).

Wiring Diagrams

1 Socket Wiring Diagram

Figure 4: Wiring diagram for 1 Socket (Non-Grounding). Connect Neutral (N) and Live (L) wires as shown.

2 Socket Wiring Diagram

Figure 5: Wiring diagram for 2 Sockets (Non-Grounding). Connect Neutral (N) and Live (L) wires as shown.

Operating Instructions

Once properly installed and powered, the WESA BZH05 electrical outlet is ready for use. Simply insert the plug of your electrical appliance into the socket. Ensure the plug is fully inserted for a secure connection.

Video 1: Product showcase of the WESA BZH05 electrical outlet.

Maintenance

  • Cleaning: To clean the surface of the outlet, wipe with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture. Always ensure power is off before cleaning.
  • Inspection: Periodically inspect the outlet for any signs of damage, such as cracks, discoloration, or loose connections. If any damage is found, turn off the power and have the outlet inspected and replaced by a qualified electrician.

Troubleshooting

If you experience issues with your WESA BZH05 electrical outlet, consider the following:

  • No Power: Check your circuit breaker. If it has tripped, reset it. If it trips again immediately, there may be a short circuit or overload. Consult a qualified electrician.
  • Loose Connection: If a plug feels loose in the socket, ensure it is fully inserted. If the problem persists, the outlet may need to be replaced by a qualified electrician.
  • Overheating: If the outlet feels warm to the touch, immediately unplug any devices and turn off power to the circuit. Overheating can indicate an overload or faulty wiring. Consult a qualified electrician.

Specifications

Feature Detail
Brand Name WESA
Model Number BZH05
Material Plastic
Socket Type Socket 220V (EU Standard)
Installation Type Wall Embedded
Rated Current 16A
Grounding Non-Grounding
Application Residential / General-Purpose
Backlight/Indication Not applicable
Extension Cable Length None
Shape Rectangular
Standard (2-Socket) 105*51*35mm
Standard (1-Socket) 83*58*39mm
Origin Mainland China
Certification CE, RoHS, WEEE

User Tips

  • Always ensure the power is off at the circuit breaker before attempting any installation or maintenance.
  • For optimal safety and performance, consider having the outlet installed by a certified electrician.
  • Avoid overloading the socket by plugging in too many high-power devices simultaneously.
  • Regularly check the outlet for any signs of wear or damage.

Warranty and Support

For detailed warranty information and customer support, please refer to the official user manual PDF or contact the seller directly through the platform where the product was purchased. The user manual PDF can be viewed here.

This product is designed for durability and safety, featuring a firm shell and quality components. It is certified with CE, RoHS, and WEEE standards.

© 2024 WESA. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.