Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your SHIMANO UR300 Flat Mount Hydraulic Disc Brake System. Designed for flat bar road bikes, this system offers reliable braking performance and ease of use. Please read this manual thoroughly before use to ensure safe and optimal performance.
Video: SHIMANO UR300 Hydraulic Disc Brake System Overview
Safety Information
WARNING: Failure to follow these safety instructions could result in serious injury or death.
- Size Compatibility: Always compare the size and specifications of this brake system with your existing components or bicycle frame to ensure compatibility and avoid purchasing inappropriate sizes.
- Professional Installation: If you lack experience in bicycle component installation, it is strongly recommended to seek assistance from a qualified bicycle mechanic or a local bicycle repair shop for proper installation. Incorrect installation can lead to brake failure and serious injury.
Package Contents
Please verify that all the following items are included in your package:
- SHIMANO BL-MT200 Brake Levers (Left and Right)
- SHIMANO BR-UR300 Flat Mount Brake Calipers (Front and Rear)
- Pre-bled Hydraulic Hoses (Front and Rear, connected to levers and calipers)
- Caliper Mounting Bolts
- Resin Brake Pads (B05S RX, pre-installed in calipers)

Image: Complete SHIMANO UR300 Hydraulic Disc Brake Set including levers, calipers, hoses, and mounting hardware.
Setup and Installation
This brake system is designed for flat mount road bike frames and forks. Ensure your frame and fork are compatible with flat mount calipers.
- Mounting Brake Levers:
- Loosen the clamp bolt on each BL-MT200 brake lever.
- Slide the levers onto your handlebar in the desired position. Ensure they are easily accessible and comfortable for your hands.
- Tighten the clamp bolts securely. Do not overtighten.

Image: Close-up of the SHIMANO BL-MT200 brake lever, showing the mineral oil specification.
- Mounting Brake Calipers:
- Identify the front and rear calipers. The front caliper has a 70mm mounting bolt spacing, and the rear caliper has a 34mm mounting bolt spacing.
- Position the BR-UR300 calipers onto the flat mount tabs on your fork (front) and frame (rear).
- Insert the appropriate mounting bolts through the caliper and into the frame/fork.
- Lightly tighten the mounting bolts. Do not fully tighten yet.

Image: Front SHIMANO BR-UR300 brake assembly, showing the caliper, hose, and lever.

Image: Rear SHIMANO BR-UR300 brake assembly, showing the caliper, hose, and lever.
- Aligning Calipers:
- Spin the wheel to ensure it rotates freely.
- Squeeze the brake lever firmly and hold it. This will center the caliper over the rotor.
- While holding the lever, fully tighten the caliper mounting bolts.
- Release the brake lever and check that the brake pads are not rubbing against the rotor. Adjust if necessary by repeating the alignment process.
- Routing Hoses:
- Route the hydraulic hoses along your frame and fork, securing them with appropriate cable ties or frame guides. Ensure there are no sharp bends or kinks in the hoses.
- Final Check:
- Before riding, test the brakes thoroughly. Ensure both front and rear brakes engage firmly and smoothly.
- Check for any leaks in the hydraulic system.
Operating Instructions
The SHIMANO UR300 system provides consistent and powerful braking. The BL-MT200 levers feature a 3-finger design for comfortable and effective braking.
- Brake Engagement: Gently squeeze the brake levers to apply braking force. The amount of force applied to the lever directly corresponds to the braking power.
- Reach Adjustment: The brake levers feature a reach adjustment screw, allowing you to customize the lever position to fit your hand size and preference. Use a small hex key to turn the screw located near the lever pivot point.
- Braking Technique: Always apply both front and rear brakes simultaneously for balanced and effective stopping. Avoid sudden, hard braking with only the front brake, especially at high speeds, as this can cause loss of control.
Maintenance
Regular maintenance ensures the longevity and performance of your brake system.
- Brake Pad Inspection: Regularly inspect the B05S RX resin brake pads for wear. Replace pads when the pad material is worn down to 0.5mm or less. Worn pads can reduce braking performance and damage rotors.
- Rotor Cleaning: Keep your disc rotors clean and free from oil, grease, or dirt. Use a clean cloth and isopropyl alcohol to clean rotors. Contaminated rotors can lead to reduced braking power and noise.
- Hydraulic Fluid: This system uses SHIMANO Mineral Oil. Do not use any other type of fluid. If the brake feel becomes spongy or inconsistent, the system may need bleeding. This procedure should ideally be performed by a qualified mechanic.
- Hose Inspection: Periodically check hydraulic hoses for any signs of damage, cracks, or leaks. Replace damaged hoses immediately.
- Bolt Torque: Ensure all mounting bolts (caliper and lever) are tightened to the manufacturer's recommended torque specifications. Refer to a bicycle repair manual or consult a professional.
Troubleshooting
- Squealing Brakes:
- Clean rotors and pads with isopropyl alcohol.
- Ensure calipers are properly aligned.
- Brake pads may be contaminated or worn; consider replacement.
- Weak Braking Power:
- Check brake pad wear and replace if necessary.
- Ensure rotors are clean and free of contamination.
- The hydraulic system may need bleeding if there is air in the lines (seek professional help).
- Brake Lever Feels Spongy:
- This usually indicates air in the hydraulic system. The brakes need to be bled by a qualified mechanic.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | SHIMANO |
| Model Number | BL-MT200+BR-UR300 |
| Type | Hydraulic Disc Brake |
| Use | Mountain Bikes (also suitable for flat bar road bikes) |
| Material | Light Alloy |
| Braking System | Hydraulic Disc Brake (Hydraulic Brake Pad) |
| Components | Disc Brake |
| Caliper Mount Type | Flat Mount |
| Front Caliper Bolt Spacing | 70mm |
| Rear Caliper Bolt Spacing | 34mm |
| Brake Fluid | SHIMANO Mineral Oil |
| Brake Pads | Resin (B05S RX) |
User Tips
- For optimal performance and quiet operation, ensure your brake pads and rotors are always clean. Avoid touching the rotor surface with bare hands.
- After initial installation, perform a few gentle stops to bed in the brake pads. This helps achieve full braking power and reduces noise.
Warranty and Support
For warranty claims, technical support, or any issues not covered in this manual, please contact your original retailer or the SHIMANO authorized service center in your region. Keep your proof of purchase for warranty purposes.