Heltec 4S

Contents

Heltec 21700 Battery Holder Instruction Manual

Model: 4S | Brand: Heltec

1. Introduction

This manual provides detailed instructions for the Heltec 21700 Battery Holder, designed for building custom 21700 battery packs. It supports 4S configurations and can be used with or without an integrated Battery Management System (BMS) for balancing and protection. The modular design allows for easy assembly without welding, making it suitable for various power wall and power bank applications.

2. Safety Information

  • No Output Without BMS: If your configuration does not include a BMS, there will be no output. Ensure you understand the implications for charging and discharging.
  • Battery Polarity: Always ensure correct battery polarity during installation. The positive and negative poles of the battery must correspond to the markings on the circuit board. Incorrect installation can cause damage to the device and batteries.
  • Short Circuit Prevention: Be careful not to insulate short circuits when using the battery holder.
  • Power Supply: Do not connect the wrong power supply (positive or negative).
  • Placement: Avoid placing the unit on conductive surfaces that could cause unintended short circuits.
  • Heat Dissipation: The design aids in heat dissipation, but ensure adequate ventilation, especially during high current operation.

3. Product Features

  • Simple, no-welding installation for 21700 batteries.
  • Excellent structure for heat dissipation during battery use.
  • Integrated insurance design for safe operation.
  • Powerful protection board (BMS) options to prevent overcharge, over-discharge, and voltage imbalance.
  • Modular design allows for stacking multiple layers to increase capacity.
  • M4 copper pillar conductive connections.
Heltec 21700 Battery Holder Features
Overview of the Heltec 21700 Battery Holder highlighting its features.

4. Specifications

General Specifications (4S Configuration)

Attribute Value
Model Number 4S
Battery Type 21700 Lithium-ion
Material ABS
Voltage Range (Input/Output) USB (5-20V DC)
Output Power 37.5-50W (including 50W)
Accessory Type Battery Accessories
Certification CE
Battery Included No
Charger Included No

Dimensions & Weight (Approximate)

  • 4S1P (without BMS): 12.5 x 8.8 x 2.5 cm, 66g
  • 4S2P (without BMS): 12.5 x 8.8 x 4.5 cm, 98g
  • 4S1P 60A BMS: 12.5 x 8.8 x 2.5 cm, 83g
  • 4S1P 120A BMS: 12.5 x 8.8 x 2.5 cm, 98g
Heltec 21700 Battery Holder Dimensions
Approximate dimensions of the 4S1P battery holder.

4S 16.8V Li-ion BMS 30A Specifications

Attribute Value
Size 110 x 90 mm
Upper Operating Current 30A
Upper Transient Current 60A
Overcharge Range 4.225V ± 0.025V
Over Voltage Range 2.7V ± 0.5V
Charging Voltage 16.8V
Equilibrium Current 56mA
Short Circuit Protection Protected, delayed self-recovery

Note: Other 'S' configurations (e.g., 3S, 6S, 7S, 8S, 10S) have different voltage and current specifications. Refer to the detailed product documentation for those models.

5. Setup and Installation

The Heltec 21700 Battery Holder is designed for easy, solderless assembly. Follow these steps carefully:

  1. Unpack Components: Ensure all parts are present: battery holder board(s), copper pillars, screws, and connection cables (if applicable to your order).
  2. 21700 4S1P Kit Components
    Typical components included in a 4S1P kit.
  3. Install Batteries: Insert 21700 batteries into the holder. Pay close attention to the polarity markings (+ and -) on the circuit board. The positive and negative poles of each battery must align with the corresponding markings.
  4. Battery Orientation Diagram
    Ensure correct battery orientation according to the circuit board markings.
    Battery Installation Example
    Example of 21700 battery installation into the holder.
  5. Stacking Layers (if applicable): If using multiple layers (e.g., 4S2P), ensure the direction of the notch on each layer is consistent. Secure the layers using the provided copper pillars and screws.
  6. Connect Cables: After the copper pillars are installed and secured, connect the balance cables (if using a BMS) and power cables to the appropriate terminals. The 4S battery box typically features a DC5.5*2.5 female charging port, XT60 output connector, and 4PIN terminals for positive and negative poles.
  7. 4S Battery Box Wiring Diagram
    Wiring diagram for the 4S battery box, showing charge and discharge points.
  8. Final Check: Before use, double-check all connections for correct polarity and secure fastening.

Installation Video Guide

This video demonstrates the installation of 21700 batteries into the holder and how to measure the output voltage.

6. Operating Instructions

Capacity and Voltage

  • The stacking of upper and lower layers increases the overall capacity of the battery pack without changing the voltage (e.g., 4S1P to 4S2P doubles capacity).
  • For a 5000mAh 21700 battery: 1P = 5AH, 2P = 10AH, 3P = 15AH, 4P = 20AH.
  • 4S Voltage: Fully charged at 16.8V, discharged at 11.6V.
  • The output power is determined by the performance of the individual batteries used. Better battery performance results in higher output current.
  • The product's protective board does not stabilize output voltage. The voltage will fluctuate between fully charged and fully discharged states.

Current Considerations

  • The average instantaneous maximum current for each layer is 20A. For prolonged use, it is recommended to keep the current below 10A per layer.

Charging Techniques

Charging Techniques for Battery Boxes
Important guidelines for charging your battery pack.
  1. The charging limit for the battery box protection board is 8A. The charging current of each battery layer should not exceed two amperes. If there is only one layer, use a charger with a current lower than two amperes. For a two-layer battery, a charger within 4A is recommended. Excessive current can cause the battery to heat up or be damaged.
  2. Always use a constant current charger, not a constant voltage power supply, as a constant voltage supply can cause significant battery heating.
  3. For a 3S configuration, a 12.6V charger is required for full charge. For a 6S configuration, a 25.2V charger is required. If the charger voltage is lower than the required value, the battery will not fully charge. If the charger voltage is higher than the required value by more than 1V, it may damage the protection board.
  4. If a suitable charger or constant voltage power supply is unavailable, consider using a constant current boost and buck module to convert a regular constant voltage power supply into an adjustable constant current power supply.
  5. When using solar panels for charging, you will need your own voltage regulator module. If the solar panel's output voltage is too low, add a boost module. If it's too high, add a buck module.

Tips for Output Usage

Tips for using battery box output
Guidance on determining capacity and power for various applications.
  1. First, determine the capacity you need. For energy storage, using a 3.7V 5000mAh 21700 battery as an example, 1P (one battery in parallel) provides 5AH.
  2. To calculate power and usage time for appliances: For a 100W appliance, assuming 100% ideal conversion efficiency, 100Wh / (3.7V * 5Ah) = 100Wh / 18.5Wh = approximately 5.4 batteries for 1 hour of use. Adjust based on actual battery capacity and appliance power.
  3. After determining the number of batteries and capacity, identify the voltage and power supply method required by your electrical appliance.
  4. If using as a power bank for mobile phones or other USB chargers, you may need a step-down USB module to convert 12V or 24V to 5V.
  5. If the required voltage for your appliance is higher than the battery box's output, you will need a boost module. If it's lower, you'll need a buck module. For variable voltage needs, a boost/buck module is recommended.

7. Maintenance

To ensure the longevity and safe operation of your Heltec 21700 Battery Holder:

  • Regularly inspect the battery holder for any signs of damage, corrosion, or loose connections.
  • Keep the unit clean and free from dust and debris.
  • Store the battery holder in a cool, dry place away from direct sunlight and extreme temperatures.
  • When not in use for extended periods, remove the batteries to prevent over-discharge or potential leakage.
  • Always use a protection board (BMS) to prevent overcharge, over-discharge, and voltage imbalance, which can extend battery life and ensure safety.

8. Troubleshooting

No Output or Charging Issues

If the battery pack cannot be charged or there is no output, carefully check the following points:

  1. Check for Link Errors: Verify all connections, especially balance cables and power terminals, for any errors or loose contacts.
  2. Activate Output: After the initial connection, use a suitable charger and charge the battery pack for a few seconds to activate the output.
  3. Individual Cell Voltage: If charging is still not possible or there is no output, measure the voltage of each battery section separately. Check for any significant voltage differences between cells or if any cell combination exceeds 4.0V, which might prevent activation. If a cell voltage is too high, lower it to around 3.7V before combining.
  4. BMS Presence: Remember that there is no output without a BMS. If you are using a configuration without a BMS, the output terminals will not provide voltage as the BMS acts as a series component in the circuit.

9. User Tips

  • Start Small: If you are new to building battery packs, consider starting with a simpler configuration (e.g., 4S1P) to familiarize yourself with the assembly process before attempting more complex stacked setups.
  • Quality Batteries: The overall performance and safety of your battery pack heavily depend on the quality of the 21700 cells you use. Invest in reputable brands.
  • External PDF Manual: For additional detailed information and diagrams, you may refer to the official user manual PDF available at: User Manual (PDF).

10. Support

For technical assistance, product inquiries, or further support, please contact the seller or manufacturer directly. Ensure you have your product model and any relevant purchase information ready.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.