CNCEST Digital Belt Cutter

Contents

280W Hot and Cold Tape Cutting Machine Digital Belt Cutter

Model: Digital Belt Cutter | Brand: CNCEST

1. Product Profile

The CNCEST 280W Hot and Cold Tape Cutting Machine is a fully automatic computer-controlled cutting machine designed for electromechanical integration. It utilizes a computer program to automatically control mechanical actions, allowing for precise cutting of various materials by length and quantity.

This versatile machine can cut different widths of woven belt, Velcro, plastic hose, shoelaces, plastic zippers, computer wires, and trademark ribbon items. Its elastic compensation function ensures high precision for diverse cutting materials.

Equipped with a heating device, it can heat-seal woven nylon belts, nylon trademarks, and other nylon materials, offering both hot and cold cutting capabilities without needing to change the cutter. An infrared positioning device, coupled with an infrared sensor system, ensures precise cutting of logos on materials of varying widths. It also features a Velcro rounded device for cutting various types of round Velcro.

The machine includes automatic storage of all set data before power-off, boasts high precision and speed, provides a level cut section, and automatically stops working when material runs out. These features contribute to improved production efficiency and product quality.

2. Specifications

Parameter Value
Power 0.28KW
Maximum Cutting Width 110mm
Cutting Length 15mm - 99999mm
Cutting Speed 100-120/min
Voltage 110/230V, 50/60HZ
Packing Size 560 x 415 x 400 (units not specified, likely mm)
Condition New
CNC or Not Normal
Is Smart Device No

For detailed information, you may refer to the official user manual PDF: User Manual (PDF)

3. Setup

3.1. Using the Environment

This machine is designed to operate under normal room temperature conditions. Operating the machine in high temperatures (above 80 degrees Celsius) may negatively affect its performance. Ensure the operating environment is within suitable temperature ranges for optimal functionality.

3.2. Initial Setup

  1. Confirm the power supply voltage matches the machine's requirements (110V or 230V) and ensure the ground wire is properly linked before use.
  2. Place the material to be cut. The material can be manually placed into the blade area when starting.
  3. When cutting magic stick feeding, ensure the rough surface faces upwards.
  4. For hot cutting, the tempering switch knob should be at '0' when the cutting knife is at room temperature. It is recommended to set the temperature between 130 and 250 degrees Celsius. After 10 minutes of temperature adjustment, you can proceed with hot cutting by pressing the automatic material button.
Tape Cutting Machine with various materials
The tape cutting machine ready for operation with various materials.
Main view of the 280W Hot and Cold Tape Cutting Machine
Main view of the 280W Hot and Cold Tape Cutting Machine.
Tape Cutting Machine with power cord, manual, and tools
The machine packaged with its power cord, user manual, and adjustment tools.

4. Operating Instructions

4.1. General Operation Process

To cut a specific number of pieces (e.g., 500 pieces) of a certain length (e.g., 120mm long strips), follow these steps:

  1. Turn on the power switch.
  2. Press the 'Number Set' key to enter the number setting state.
  3. Press the 'Set' key repeatedly to adjust the desired number of pieces. Use the 'Up' (▲) and 'Down' (▼) keys to increase or decrease the numbers. Set unwanted bits to zero. Press 'Set' again to confirm the number.
  4. Press the 'Length Set' key to enter the length setting state.
  5. Press the 'Set' key repeatedly to adjust the desired cutting length. Use the 'Up' (▲) and 'Down' (▼) keys to increase or decrease the numbers. Set unwanted bits to zero. Press 'Set' again to confirm the length.
  6. After all settings are complete, press the 'Stop/Start' button to begin the automatic cutting process.

4.2. Panel Function Introduction

Close-up of the machine's control panel with buttons and digital display
Close-up of the machine's control panel, showing the digital display, length and number setting buttons, and power switch.

The control panel features the following:

  • Power Switch: Turns the machine on/off.
  • Length Set: Enters the length setting state.
  • Number Set: Enters the number of pieces setting state.
  • Forward (▲): Increases the displayed value or moves to the next digit during setting.
  • Back (▼): Decreases the displayed value or moves to the previous digit during setting.
  • Stop/Start: Initiates or halts the cutting operation.
  • Display: Shows the current length or quantity settings.
  • Length Pilotlamp: Indicator for length setting.
  • Quantity Pilotlamp: Indicator for quantity setting.
  • Runpilot: Running indicator light.
  • Trouble Lamp: Trouble indicator light.
Video demonstrating the operation of the control panel, including setting length and quantity.

5. Maintenance

5.1. General Considerations

  • For safety, never place hands or any objects near the cutting knife during operation.
  • Always cut off power before making any adjustments to ensure safety.
  • Do not remove any spare parts unless for normal maintenance procedures.
  • Ensure to add oil to moving parts once before starting operation.

5.2. How to Change a Knife

  1. Use a cross screwdriver to loosen the four 3mm bolts on the safety cover and remove the cover.
  2. Use a 2.5mm inner hexagon wrench to loosen the two 5mm hexagonal bolts at the top of the tool holder.
  3. Unscrew the hexagon screw of the upper knife with a 4mm hexagonal spanner and remove the upper knife.
  4. Remove the hexagon screw of the lower knife with a 4mm hexagonal spanner and remove the lower knife.
  5. Press the new lower knife into its original position, securing it with a 3-5mm cylinder head hexagon screw with fixed pressure.
  6. Install the new knife onto the tool post. Do not overtighten the fixed clamp. Manually press the M/CUT key to bring the knife into contact with the knife edge. Slightly tighten the 3-5mm cylinder head hex socket screws on the tool rest.
  7. Use the M/CUT key to test shearing with paper or thin fabric to verify correct knife installation.
  8. If the cut is normal, firmly press the three 5mm cylinder screws on top of the upper knife rack.
  9. Re-install the safety cover.
Side view of the cutting machine
Side view of the cutting machine, showing the cutting mechanism.
Angled view of the machine with material reel
Angled view of the machine, demonstrating material feeding from a reel.

6. Troubleshooting

Refer to the table below for common issues and their solutions:

No. Condition Cause and Measures
1. Non-transformer Check if the power connection plug wire is in good contact. Check if the fuse is disconnected.
2. There is power but cannot start Check for clutter on the roller. If the display shows a tool sensor error, turn off and on power after 10 seconds. If the control panel green light is on, press control panel 5, cut off the knife rack, and move up and down. If the display is still abnormal, turn off and on power after 10 seconds, press start button green key. If it still cannot start, consider changing the drive board.
Non-starter Inspect pressure plate (cold knife #20 & #29, hot knife #32 & #36). Is it too tight? If the machine works for a long time, the cabinet temperature may be super high, causing abnormal behavior.
Screen no display Stop working, turn off the power switch, turn it on again later, and the display should be normal. If the boot display is not normal during cold start, turn off the power and wait 10 seconds before starting. If repeated attempts fail, open the box cover to check the computer and wiring.
3. Unable to cut off tape Check whether the temperature reaches the preset temperature. Check whether the hot knife is heated.
4. Just cut off the side of the tape Check to see if the heat is damaged or worn. The knife is adjusted by hand cutting, and the upper and lower knives are aligned and maintained.
5. The cut length is different from the set value Loosen roller or use belt conveyor.
6. When the trademark was cut off, it didn't arrive. The cutting line is cut off. Move the sensor toward the edge of the knife.
7. When cutting off a trademark, the cut line is cut off Move the sensor to the back of the knife.
8. The display screen displays errors Sensor failure. Check whether the sensor is linked well. Check whether the cursor of the color standard sensor is tuned to the detected reference. Check the length and set the length of the key to match the length of the trademark.
9. A hand touching the machine feels electric current In the installation of the equipment, the user should be equipped with an electric leakage switch, a triangle socket, and the grounding pole must have a good grounding line to ensure the normal work of the machine.

6.1. Schematic Circuit Diagram

Schematic circuit diagram of the automatic cutting machine
Schematic circuit diagram illustrating the internal wiring and components of the automatic cutting machine, including power outlet, fuse holder, cutter servo motor, stop switch, power and drive board, color mark sensor, tool holder sensor, and cooling fan.

7. User Tips

  • Cutting Width: The machine supports a maximum cutting width of 110mm. This means it can comfortably cut materials up to approximately 4 inches wide.
  • Round Cuts: The machine is equipped with a 'Velcro rounded device' designed to cut various types of round Velcro. While specific sizes like 26mm are not detailed, its capability for round cuts is confirmed.
  • Material Feeding: Always ensure the material is fed correctly, especially for magic stick feeding, where the rough surface should face upwards for optimal cutting.
Diagram showing correct and incorrect material placement
Diagram illustrating the correct (毛面朝上 - rough side up) and incorrect (毛面朝下 - rough side down) ways to place material for cutting.

8. Warranty and Support

For any difficulties in operation or technical support, please contact the seller or manufacturer directly. They are committed to serving you wholeheartedly.

Please refer to your purchase documentation for specific warranty terms and conditions.

© 2024 CNCEST. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.