1. Introduction
The HORACO 10G SFP+ Fiber to RJ45 Media Converter is an Ethernet transmission medium conversion unit designed to convert short-distance Ethernet cable electrical signals into long-distance optical signals, and vice versa. This device is suitable for long-distance data transmission and data aggregation applications, offering plug-and-play functionality and high compatibility.
It supports fiber optic transmission distances up to 3-120 kilometers, depending on the optical module used. The fiber optic module supports single-mode/multi-mode, and single fiber/dual fiber configurations.
Key Characteristics:
- Achieves up to 100KM of data transmission through fiber optic access.
- Supports port lightning protection.
- Adopts a store-and-forward exchange mechanism.
- All ports support line speed switching and giant frame transmission.
- Features zero configuration, automatically adapting to connected devices.
- Panel indicator lights monitor working status and assist in fault analysis.
- Supports IEEE802.3af/at/bt (limited to PoE BT series models).


2. Safety Information
For the safe installation and operation of the media converter, please observe the following recommendations:
- Ensure the power cord is securely wrapped around the AC power connector.
- Provide proper heat dissipation and ventilation around the device.
- Do not stack heavy objects on top of the media converter.
- The device is certified with CE, FCC, and RoHS standards.

3. Package Contents
The package contents vary slightly depending on whether you have a non-PoE or PoE model.
Non-PoE Product Accessories:
- One Media Converter Unit
- One Power Adapter
- A User Manual and Warranty Card
PoE Product Accessories:
- One Media Converter Unit
- One External Power Cord + One Power Adapter
- A User Manual and Warranty Card
Attention:
- SFP models do not include optical modules by default.
- If you find any shortage or damage to accessories, please contact your supplier promptly.
4. Setup
Desktop Installation:
When installing the media converter on a desktop, ensure the device is placed horizontally and remains stable. Leave sufficient space around the device and other surrounding objects to allow for adequate ventilation.

Power Connection:
The media converter uses a two-wire power socket, and the power cord typically uses a single-phase three-wire power socket. Ensure the middle pin is for grounding, the left pin for neutral, and the right pin for live wire. Always check these connections before operation.
- Verify that the power supply matches the requirements indicated on the media converter.
- The adapter and power cord+adapter can be directly connected to an AC 100~240V, 50/60Hz mains power outlet.

SFP Port Connection:
To install a fiber optic module:
Grasp the fiber optic module from the side and smoothly insert it along the SFP port slot of the media converter until it is in close contact with the switch.
Check After Installation:
After completing the installation, please verify the following:
- Ensure there is sufficient heat dissipation space around the media converter and that air circulation is smooth.
- Confirm that the power supply of the power socket meets the specifications of the media converter.
- Check that the power supply, media converter, and any other connected equipment are properly grounded.
5. Operation
LED Indicators:
The media converter features LED indicators to monitor its working status and assist in fault analysis. Refer to the table below for indicator definitions:
| Indicator | State | Description |
|---|---|---|
| Power indicator: PWR | On | Power on |
| Off | Power off | |
| Blink | Port short circuit or excessive load current | |
| Link (Right) | Off | The corresponding optical port is not connected |
| On | Corresponding optical ports have connections | |
| Blink | Corresponding optical port connection and communication | |
| R/G (Right) | Off | The corresponding optical port does not work in this mode |
| On (Red) | The corresponding optical port is connected and operates in 10G mode | |
| On (Green) | The corresponding optical port is connected and operates in 2.5G mode | |
| EX (Non-PoE) | Off | Nothing |
| On | Nothing | |
| EX (PoE) | Off | PoE Watchdog off |
| On | PoE Watchdog on | |
| Link (Left) | Off | The corresponding network port is not connected |
| On | There is a connection to the corresponding network port | |
| Blink | Corresponding network port connection and communication | |
| R/G (Left) | Off | The corresponding network port does not work in this mode |
| On (Red) | The corresponding network port is connected and operates in 10G mode | |
| On (Green) | The corresponding network port is connected and operates in 2.5G mode |
Application Scenarios:
The HORACO 10G Media Converter can be integrated into various network environments to extend or convert network connections. Below are common application diagrams:



6. Maintenance
To ensure optimal performance and longevity of your HORACO 10G Media Converter, follow these maintenance guidelines:
- Keep Clean: Regularly clean the exterior of the device with a soft, dry cloth. Avoid using liquid cleaners or solvents.
- Ensure Ventilation: Always ensure that the ventilation openings are clear and unobstructed to allow for proper airflow and heat dissipation. Do not place the device in enclosed spaces without adequate air circulation.
- Cable Management: Keep all connected cables organized and free from kinks or excessive tension to prevent damage to ports and cables.
- Power Supply: Use only the provided power adapter. If the adapter is damaged, replace it with an approved equivalent.
7. Troubleshooting
If you encounter issues with your media converter, refer to the following common problems and solutions:
- No Power: If the PWR indicator is off, ensure the power adapter is securely connected to both the device and a working power outlet. Check the power outlet with another device.
- No Link on Optical Port: If the right Link indicator is off, check the SFP module installation and ensure the fiber optic cable is correctly connected and undamaged. Verify the SFP module is compatible.
- No Link on RJ45 Port: If the left Link indicator is off, check the Ethernet cable connection and ensure it is properly seated in the RJ45 port. Test with a different Ethernet cable.
- Incorrect Speed Indication: If the R/G indicator shows an unexpected color (e.g., green for 10G mode when red is expected), verify the connected devices support the desired speed and that the cables meet the required specifications (e.g., Cat6 or later for 10GBASE-TX).
- PoE Issues (for PoE models): If PoE devices are not receiving power, check the EX (PoE) indicator. Ensure the PoE watchdog is enabled if desired and that the connected device is PoE compatible.
- General Connectivity Issues: If the device is not functioning as expected despite correct connections, try restarting the media converter by disconnecting and reconnecting the power.
- VLAN Passthrough: The device supports VLANs (up to 4K VLAN addresses). If VLANs are not passing through, ensure your network configuration is correct and the media converter is not misconfigured (though it is generally zero-configuration).
8. Specifications
The following table details the technical parameters of the HORACO 10G SFP+ Fiber to RJ45 Media Converter (Model LG-10GE-XS) and its PoE variants:
| Parameter | LG-10GE-XS | LG-10GES-P(30W) | LG-10GES-P(90W) |
|---|---|---|---|
| Fixed Port | 1*100M/1G/2.5G/5G/10G RJ45, 1*1G/2.5G/10G SFP+ | 1*100M/1G/2.5G/5G/10G PoE RJ45, 1*1G/2.5G/10G SFP+ | 1*100M/1G/2.5G/5G/10G PoE RJ45, 1*1G/2.5G/10G SFP+ |
| PoE Port | N/A | 1 port supports IEEE802.3af/at MAX 30W | 1 port supports IEEE802.3af/at MAX 90W |
| Bandwidth | 40Gbps | ||
| Packet Forwarding Rate | 29.76Mpps | ||
| MAC Address Table | 8K | ||
| Packet Buffer | 8.1M | ||
| Jumbo Frame | Max 12KB | ||
| VLAN Address | 4K | ||
| Function | Force fiber optic to reach 2.5G speed | PoE watchdog | |
| Transmission Distance | 100BASE-TX: Cat5 or later UTP (150m) 2500/1000BASE-TX: Cat6 or later UTP (100m) 5G BASE-TX: Cat6 or later UTP (80m) 10G BASE-TX: Cat6 or later UTP (50m) SFP: 100M/1G/2.5G/10G single-mode/multimode optical module, maximum distance ≤ 120km (depending on optical module) | ||
| Power Input | DC12V 1A (5.5*2.1mm) | DC52V 0.6A (5.5*2.5mm) | DC52V 2.5A (5.5*2.5mm) |
| Operating Temperature/Humidity | -20~+60°C; 5%~90% RH Non-coagulation | ||
| Storage Temperature/Humidity | -40~+85°C; 5%~95% RH Non-coagulation | ||
| Product Size (L*W*H) | 70mm*93mm*28mm | ||
| Net Weight / Gross Weight | 0.2kg / 0.75kg | ||
| Lightning Protection Level | 6KV 8/20us, IP30 | ||
| Installation Method | Desktop or DIN installation method | ||
| Certification | CE-EMC EN55032; CE-LVD EN62368; FCC Part 15 Class B, RoHS | ||
9. User Tips
- SFP+ Module Compatibility: The converter has been reported to work well with various 10GBASE-LR SFP+ transceivers. Ensure your chosen SFP+ module is compatible with the 1G/2.5G/10G adaptive SFP+ port.
- Plug and Play: Many users find the device to be truly 'plug and play' with no complex configuration required for basic operation.
- Interoperability: The converter has been successfully connected with DAC cables to other brands of 10Gbps switches (e.g., TP-Link) and routers (e.g., Asus) with RJ45 ports, indicating good interoperability.
- Power Supply Consideration: While the device comes with its own power adapter, some users suggest that a USB Type-C power connector might be a more convenient alternative if you have compatible USB power sources available.
10. Warranty & Support
The HORACO 10G SFP+ Fiber to RJ45 Media Converter comes with a 1-year warranty for the whole device. Accessories are not included in the warranty.
For further assistance, detailed instructions, or to view the official user manual in PDF format, please refer to the following document: User Manual (PDF).
11. Frequently Asked Questions (FAQ)
- Does this device support VLAN passthrough?
Yes, the media converter supports VLANs with a capacity for 4K VLAN addresses. - Does the product come as a single converter or a pair?
The product is sold as a single media converter unit. If you need to extend a fiber optic link between two locations, you will typically need two units (a pair).