JHao Xin GT

Contents

User Manual: DRL Chip Ballast Circuit Board for Peugeot GT Headlights

1. Introduction

This manual provides essential information for the safe and effective installation and use of your DRL (Daytime Running Light) Chip Ballast Circuit Board. This product is designed as a replacement light source board chip for the headlights of Peugeot GT 4008 and 5008 models manufactured between 2017 and 2020, providing white light for your vehicle's DRL system.

2. Safety Information

Please read all safety warnings carefully before installation and use. Failure to follow these instructions may result in injury or damage to the product or vehicle.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • This is a highly specialized operation. Be sure to find a professional installer. Beginners should not attempt to install it.

3. Package Contents

Depending on your order, your package will contain:

  • One (1) or two (2) DRL Chip Ballast Circuit Board(s)

Ensure all components are present and undamaged upon receipt.

DRL Chip Ballast Circuit Board

Image: A single DRL Chip Ballast Circuit Board, showing the connector and LED components.

4. Setup and Installation

Installation of this product requires specialized knowledge and tools. It is strongly recommended that installation be performed by a qualified professional technician.

  1. Disassemble the car headlights: Carefully remove the headlight assembly from the vehicle.
  2. Heat the headlights: Apply heat to the headlight assembly, typically between 90°C and 150°C. The exact temperature may vary depending on the type of adhesive used in your specific headlight unit.
  3. Separate components: After heating, use a suitable headlight solution to carefully separate the lens from the rear housing. Remove the original DRL components.
  4. Install the replacement part: Position the new DRL Chip Ballast Circuit Board into the headlight assembly. Ensure proper alignment and connection.
  5. Seal the assembly: Reassemble the headlight components using appropriate sealant to ensure a watertight seal.
  6. Reinstall headlight: Mount the headlight assembly back into the vehicle and test its functionality.
DRL circuit board next to Peugeot headlight

Image: The DRL circuit board positioned near a Peugeot headlight, illustrating its intended application.

Top view of DRL circuit board

Image: Top view of the DRL circuit board, showing the multi-pin connector and the LED chips.

Bottom view of DRL circuit board

Image: Bottom view of the DRL circuit board, revealing the circuit traces and surface-mounted components.

Angled view of DRL circuit board with voltage and wattage

Image: Angled view of the DRL circuit board, showing markings for 13.5V and 20W.

Functionality Test Video

Video: A demonstration of the DRL chip lighting up when power is applied, confirming its operational status.

5. Operating Instructions

Once correctly installed, the DRL Chip Ballast Circuit Board operates automatically as part of your vehicle's Daytime Running Light system. It provides a consistent white light output when the DRL function is active, as per your vehicle's factory specifications.

6. Maintenance

This DRL circuit board is a sealed electronic component and requires no user maintenance. To ensure its longevity and proper function, ensure the headlight assembly remains sealed, clean, and free from moisture and debris.

7. Troubleshooting

  • DRLs not working after installation:
    1. Verify all electrical connections are secure and correctly made.
    2. Ensure the headlight assembly is properly sealed and no moisture has entered.
    3. If the issue persists, consult the professional installer or a qualified automotive electrician to diagnose the problem.
  • Intermittent DRL function: This could indicate a loose connection or an issue with the vehicle's electrical system. Professional inspection is recommended.

8. Specifications

FeatureSpecification
Brand NameJHao Xin
Model NameGT
Item TypeBallast (DRL Chip)
Light ColorWhite
CompatibilityPeugeot GT 4008, 5008 (2017-2020)
Operating Voltage13.5V
Power Output20W
Package Length18 cm
Package Width15 cm
Package Height3 cm
Package Weight0.04 kg (40g)
OriginMainland China
High-concerned chemicalNone

9. User Tips

  • Verify Compatibility: Always double-check that this DRL chip is compatible with your exact vehicle model and year (Peugeot GT 4008 or 5008, 2017-2020) before attempting installation. Compatibility with other models, such as the Peugeot 3008 GT Line, is not guaranteed.
  • Professional Installation: Due to the complexity of headlight disassembly and reassembly, professional installation is highly recommended to prevent damage to the product or your vehicle's headlights.

10. Warranty and Support

For any questions, technical support, or warranty inquiries, please contact your seller directly. Provide your purchase details and product model for efficient assistance.

Manufacturer Information:
Yiwu Xinyu Trading Co., Ltd.
Room 503, No. 22, Liuruitang Road, Choujiang Street,
Yiwu City, Zhejiang Province, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.