Paweinuo 900000LM 180COB Solar Street Light User Manual

1. Introduction

Thank you for choosing the Paweinuo 900000LM 180COB Solar Street Light. This powerful outdoor lighting solution is designed to provide ultra-high brightness and security for various outdoor spaces such as front doors, pathways, gardens, garages, and yards. Featuring a motion sensor and three smart lighting modes, this light offers convenience and energy efficiency.

This manual provides essential information for the safe and effective use of your solar light. Please read it thoroughly before installation and operation.

2. Safety Precautions

• Ensure the installation surface is stable and can support the weight of the light.
• Do not attempt to disassemble or modify the product, as this may void the warranty and cause damage.
• Keep the solar panel clean to ensure optimal charging efficiency.
• Avoid placing the light in areas where it may be submerged in water, despite its IP65 rating.
• Handle the product with care to prevent damage to the solar panel or LED components.

3. Package Contents

Please check the box for the following items:

• 1 x Paweinuo 900000LM 180COB Solar Street Light
• 1 x Remote Control
• 1 x Mounting Bracket
• 1 x Set of Installation Screws and Wall Plugs

4. Specifications

5. Setup and Installation

5.1 Initial Charging

Before first use, fully charge the solar light by placing it in direct sunlight for 6-8 hours. This ensures the internal lithium battery is adequately charged for optimal performance.

5.2 Choosing an Installation Location

Select a location that receives direct sunlight for most of the day. The solar panel should ideally face south to maximize sun exposure. Ensure there are no obstructions (like trees, buildings, or glass) that could block sunlight from reaching the solar panel.

5.3 Mounting the Light

1. Prepare the Light: Locate the main ON/OFF switch on the light. Firstly, turn the main switch to ON.
2. Mark Drill Points: Hold the mounting bracket against the desired installation surface and mark the positions for the three screw holes.
3. Drill Holes: Use a drill to create holes at the marked positions. Insert the wall plugs into the drilled holes.
4. Secure the Bracket: Attach the mounting bracket to the wall using the provided screws.
5. Attach the Light: Slide the solar light onto the secured mounting bracket. The bracket allows for an adjustable angle to optimize light direction.

5.4 Remote Control Preparation

Before using the remote control, please remove the transparent insulating sheet (plastic tab) from the battery compartment to activate it.

6. Operating Instructions

Your solar light features three smart lighting modes, controllable via the remote control or the ON/OFF switch on the unit. The motion sensor has a sensing range of approximately 5 meters (16 feet) and a 120-180 degree detection angle.

6.1 Lighting Modes

• Mode 1 (Induction Mode): The light remains off when no motion is detected. When motion is sensed, it turns on with strong brightness and automatically turns off after approximately 30 seconds of no further motion.
• Mode 2 (Dim Light Induction Mode): The light stays on at a dim level in darkness. When motion is detected, it brightens to full intensity and returns to dim light after approximately 30 seconds of no further motion.
• Mode 3 (Medium Light Mode): The light automatically turns on at a constant medium brightness after dark and stays on continuously without induction function. It automatically turns off and charges at dawn.

6.2 Using the Remote Control

The remote control allows you to easily switch between the three lighting modes and turn the light ON/OFF. Point the remote control towards the light's sensor receptor to change settings.

7. Maintenance

• Cleaning the Solar Panel: Regularly wipe the solar panel with a soft, damp cloth to remove dust, dirt, or debris. A clean panel ensures maximum sunlight absorption and charging efficiency.
• Cleaning the Light Fixture: Clean the LED light surface and motion sensor window periodically to maintain optimal light output and sensor sensitivity.
• Battery Care: The built-in lithium battery is designed for long-term use. Avoid prolonged storage of the light in a completely discharged state.

8. Troubleshooting

• Light does not turn on at night:
  • Ensure the main switch is ON.
  • Verify the solar panel is receiving sufficient direct sunlight during the day (6-8 hours).
  • Check if the solar panel is dirty or obstructed. Clean it if necessary.
  • If testing during the day, remember to cover the solar panel to simulate darkness.
• Motion sensor not working:
  • Ensure the sensor window is clean and unobstructed.
  • Check the selected lighting mode; Mode 3 does not use the motion sensor.
  • Confirm the remote control's insulating sheet has been removed.
• Light duration is short:
  • The solar panel might not be getting enough direct sunlight for a full charge. Relocate if possible.
  • Weather conditions (overcast days) can affect charging efficiency.

9. User Tips

Based on general user experiences with solar lights:

• For best performance, ensure the solar panel is cleaned regularly, especially in dusty or snowy environments.
• Consider installing the light at a height that optimizes both motion detection and light coverage for your specific area.
• Experiment with the different lighting modes to find the one that best suits your security and energy-saving needs.

10. Warranty and Support

This product comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or improper installation.

For warranty claims or technical support, please contact the seller or retailer from whom you purchased the product. Provide your purchase details and a description of the issue for prompt assistance.