NOPARDE GJ

Contents

NOPARDE GJ LED Projector Light User Manual

Model: GJ

1. Introduction

Thank you for purchasing the NOPARDE GJ LED Projector Light. This device is designed for customizable logo projection, suitable for various indoor and outdoor advertising and decorative purposes. Please read this manual carefully before installation and operation to ensure safe and optimal performance.

NOPARDE LED Projector Light projecting a 'Bakery' logo onto a street

Figure 1: NOPARDE LED Projector Light in an outdoor projection scenario.

Video 1: Demonstration of the NOPARDE LED Projector Light in various applications.

2. Safety Precautions

  • Always ensure the power is off before installation, maintenance, or lamp replacement.
  • Do not disassemble the product yourself. Any unauthorized disassembly will void the warranty.
  • Lamps that are not waterproof (if applicable to a specific model variant) should not be installed in outdoor areas where they can get wet.
  • For waterproof lamps, ensure the 'waterproof fixing iron ring' is securely tightened to prevent water ingress.
  • The lamp surface can become hot after extended use. Exercise caution to avoid burns during handling.

3. Setup and Installation

3.1 Installation Methods

The projector supports multiple installation modes and offers 360° adjustability. Use the provided screws to securely fix the bracket to the desired surface.

Diagram showing wall, hoisting, and seated installation modes

Figure 2: Multiple installation modes (Wall, Hoisting, Seated) with 360° adjustability.

Close-up of projector head showing 360 degree adjustment

Figure 3: Projector head showing 360° adjustment capability.

3.2 Waterproofing Note

After adjusting the clarity and position, always remember to securely tighten the waterproof iron ring to maintain the device's IP67 rating and prevent water ingress.

Image of the waterproof iron ring component

Figure 4: The waterproof iron ring component.

4. Operating Instructions

4.1 Power On/Off

Plug the projector into a suitable AC power outlet. The light will turn on automatically. If your model includes a remote control, use the 'ON/OFF Power Switch' button on the remote.

4.2 Adjusting Projection Clarity

To adjust the clarity of the projected image, gently twist the lens outwards or inwards. Be careful not to drop the lens. For indoor use, optimal adjustment is typically achieved within 2 to 3 meters of projection distance.

4.3 Adjusting Projection Angle and Rotation

To adjust the projection angle, first unscrew the stand counterclockwise, set the desired angle, and then tighten it again. If your model supports rotation, use the remote control to manage this feature.

4.4 Remote Control Functions

If your projector comes with a remote control, use it to manage various functions:

  • Light Switch: Turns the projection light on or off.
  • Sleep Mode: Activates a low-power or standby mode.
  • Rotation/Rest: Controls the rotation of the projected pattern or stops it.
  • ON/OFF Power Switch: Main power control for the unit.
Diagram of the remote control with labeled buttons

Figure 5: Remote control diagram with button functions.

5. Maintenance

5.1 Lamp Replacement

When the projection quality degrades, you may need to replace the light sheet (gobo). Follow these steps:

  1. Power Off: Ensure the projector is completely powered off and unplugged.
  2. Cool Down: Allow the lamp to cool down completely, as it can be very hot after use.
  3. Remove Front Bezel: Carefully remove the screws securing the front bezel and detach it.
  4. Remove Retaining Ring: Locate and remove the retaining ring that holds the light sheet in place.
  5. Replace Light Sheet: Carefully remove the old light sheet. Insert the new light sheet, ensuring the black side faces outward.
  6. Reassemble: Secure the new light sheet with the retaining ring, then reattach the front bezel and its screws.

6. Troubleshooting

If you encounter any problems with your NOPARDE GJ LED Projector Light, please do not attempt to disassemble or repair it yourself. Contact customer service immediately for assistance. Unauthorized disassembly will void your warranty.

7. Specifications

Diagram showing product parameters and dimensions

Figure 6: Product dimensions for metallic silver and quality black versions.

FeatureSpecification
ModelGJ (BHL-X6D)
Voltage110-250 V
Input Power25-100 W
Luminous Flux2000-82000 Lumens
Working Environment-40°C to 60°C
Waterproof LevelIP67
Lamp Diameter37 mm
Product Weight1.7 KG
Body MaterialAluminum Alloy
Heat Dissipation ModeHeat Conduction Technology
Installation ModeSelf-contained (Ceiling/Wall)
Bulbs IncludedNo
High-Concerned ChemicalNone

8. User Tips

  • Custom Gobo Designs: This projector is customizable. You can provide your logo source files, photos, or text to the seller for custom light sheet (gobo) designs.
  • Optimal Clarity: For the best projection clarity, ensure the lens is clean and free from dust. Adjust the lens carefully for sharp images.
  • Secure Installation: Always double-check that the projector is securely mounted according to your chosen installation method to prevent accidental falls.

9. Warranty and Support

9.1 Warranty

This NOPARDE GJ LED Projector Light comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects under normal use. It does not cover damage caused by misuse, unauthorized modifications, or failure to follow instructions in this manual.

9.2 Customer Support

For any product-related issues, technical support, or warranty claims, please contact the seller's customer service. Do not attempt to repair the device yourself, as this will void the warranty.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.