SZRZGT DC5-24V 30A LED Dimmer

Contents

SZRZGT DC5-24V 30A LED Strip Light Knob Switch Dimmer User Manual

Model: DC5-24V 30A LED Dimmer

Brand: SZRZGT

1. Product Overview

This product is a DC5-24V universal single-color LED dimmer controller using PWM digital dimming technology, paired with a 2.4G wireless remote control. It enables on/off control, precise brightness adjustment, and group control for LED strips/lights. It is compatible with 12V/24V low-voltage LED strips, light bars, spotlights, and other constant-voltage LED loads, with smooth flicker-free dimming and long-range wireless control (up to 20-30 meters line-of-sight).

SZRZGT D01 Dimmer and Remote for Single Color LED Strips
SZRZGT D01 Dimmer and Remote for Single Color LED Strips
SZRZGT D02 CCT Controller and Remote for Dual Color LED Strips
SZRZGT D02 CCT Controller and Remote for Dual Color LED Strips

2. Package Contents

ItemQuantityNotes
2.4G Wireless Remote Control1 pcPre-installed with CR2032 coin cell battery
LED Dimmer Controller1 pcRed wire = positive (+), black wire = negative (-)
User Manual1 pcIncludes installation, operation, and troubleshooting guides

3. Technical Specifications

ParameterSpecification
Input VoltageDC 5V / 12V / 24V (wide voltage range)
Max Load Power12V: 96W; 24V: 192W (single channel)
Dimming MethodPWM digital dimming, 256 gray levels
Remote Frequency2.4GHz ISM band
Remote Control Distance≤30m (line-of-sight); ≤20m (with obstacles)
Operating Temperature-10℃ ~ 60℃
Wireless Protocol2.4G two-way communication

4. Safety Notes

⚠️ WARNING!

  • This product is only for DC5-24V constant-voltage LED loads. Do NOT connect to AC220V high voltage, as this will cause permanent damage and safety hazards.
  • Always verify wiring polarity before powering on; reversed polarity may damage the controller. Ensure no short circuits exist after wiring.
  • Install the controller in a well-ventilated, dry area away from moisture, high temperatures, and strong magnetic fields to prevent malfunction.
  • Do not disassemble the controller; only qualified technicians should perform repairs.
  • Disconnect power when not in use to extend product lifespan.

5. Installation & Wiring Steps

5.1 Controller Wiring

Safety Precaution: Always disconnect all power before wiring! Do NOT work on live circuits!

The controller terminals are labeled for Power Input and LED Output (V+ = positive, V- = negative). Match polarities strictly:

  • Power Input: Connect the positive (+) wire of your 12V/24V power supply to the controller's V+ terminal, and the negative (-) wire to V-.
  • LED Output: Connect the positive (+) wire of your LED strip/light to the controller's LED+ terminal, and the negative (-) wire to LED-.
  • After wiring, check for secure connections and exposed copper strands; insulate all exposed wires with electrical tape.
Wiring diagram for connecting the LED dimmer controller to a power supply and single color LED strip.
Wiring diagram for connecting the LED dimmer controller to a power supply and single color LED strip.

5.2 Remote Control Battery Installation

The remote is pre-installed with a CR2032 coin cell battery. If the remote is unresponsive, open the back cover and reinsert the battery with correct polarity (+/-).

6. Remote Control Button Functions

Button LabelFunction DescriptionOperation
(Power On/Off)One-touch control for all paired lightsShort press: Quick on/off; Long press: Continuous on/off toggle
(Group On/Off)Group control for partitioned lighting zonesShort press: Toggle selected group; Long press: Continuous group toggle
(Brightness +)Increase light brightnessShort press: Fine-tune (1% per step); Long press: Rapid brightening
(Brightness -)Decrease light brightnessShort press: Fine-tune (1% per step); Long press: Rapid dimming
(Preset Buttons)Quick access to pre-set brightness levelsPress to cycle through 25% / 50% / 75% / 100% brightness presets

7. Pairing & Grouping (Required for First-Time Use)

7.1 Single Light Pairing (1:1)

  1. Power on the controller; its indicator light will flash rapidly (entering pairing mode).
  2. Press the Group On/Off button 3 times; the light will flash slowly 3 times to confirm successful pairing.
  3. Repeat for additional lights if needed.

7.2 Bulk Pairing (All Lights)

  1. Power on all controllers to be paired; their indicator lights will flash rapidly.
  2. Press the Power On/Off button 3 times; all lights will flash slowly 3 times to confirm bulk pairing.

7.3 Group Pairing (Multi-Zone Control)

  1. Power on the first group of controllers; their indicator lights flash.
  2. Press the corresponding Group On/Off button (e.g., Group 1) 3 times; the first group of lights flashes slowly 3 times to confirm pairing.
  3. Power off the first group, then power on the second group. Press the Group 2 On/Off button 3 times to pair the second zone, and so on.

8. Clearing Pairings & Re-Pairing

8.1 Full Clear (All Pairings)

  1. Disconnect power from the controller, wait 10 seconds, then reconnect power (indicator light flashes rapidly).
  2. Press the Power On/Off button 6 times; all lights flash quickly 6 times to confirm full clearing (remote will no longer control the controller).

8.2 Group Clear (Single Zone)

  1. Disconnect power from the target group controller, wait 10 seconds, then reconnect power (indicator light flashes).
  2. Press the corresponding Group On/Off button 6 times; the group lights flash quickly 6 times to confirm group clearing.

8.3 Re-Pairing

After clearing, re-perform the pairing steps in Section 7 to re-establish control.

9. Troubleshooting

SymptomPossible CauseSolution
Remote unresponsive1. Dead remote battery
2. Unpaired remote/controller
3. Reversed battery polarity
1. Replace CR2032 battery
2. Re-pair remote and controller
3. Correct battery polarity
Lights not turning on1. No power supply
2. Reversed wiring polarity
3. Overloaded controller
4. Damaged controller
1. Check power switch and connections
2. Reverse incorrect wiring polarity
3. Reduce load or use higher-power controller
4. Contact support for replacement
Inaccurate brightness adjustment1. Excessive distance/obstacles
2. Strong electromagnetic interference
1. Move remote closer to controller
2. Keep away from routers, motors, or other EMI sources
Flickering lights1. Loose wiring
2. Unstable power supply voltage
3. Voltage drop from long LED strips
1. Retighten all wiring terminals
2. Replace with a stable matched power supply
3. Shorten LED strip length or use dual-wire power feeding

10. User Tips

  • If your remote control seems unresponsive or the lights are not dimming/turning off correctly, first check the remote's battery and ensure it is installed with the correct polarity.
  • Always ensure the remote is within the specified operating range (up to 30 meters line-of-sight) and that there are no significant obstacles or sources of electromagnetic interference between the remote and the controller.
  • For optimal performance and longevity, avoid overloading the controller beyond its maximum rated power for your specific voltage (e.g., 96W for 12V, 192W for 24V).

11. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For technical support, warranty claims, or replacement parts, please contact the seller or manufacturer directly. Please refer to the original purchase documentation for specific warranty terms and contact information.

For additional information and documents, you may refer to the User manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.