1. Introduction
Thank you for purchasing the Q4AC balance charger. Please read this manual carefully before use to ensure proper operation and safety.
Key Points
- Tips: Helpful advice for optimal use.
- Important: Critical information to prevent damage or injury.
- Information: General details and explanations.
Further Information
To ensure you have the best experience with this product, scan the QR code below to stay up to date with news, information, and firmware updates for your charger. You can also visit www.toolkitrc.com.

2. Safety Information
Failure to follow these safety instructions may result in damage to the product, property, or personal injury.
- Input Voltage: The Q4AC supports AC 100V-240V and DC 10-18V input. Ensure the power supply voltage is consistent with the charger's requirements. Pay close attention to the positive and negative polarity when connecting the DC power supply.
- Environment: Do not use this product in environments with excessive heat, humidity, flammable liquids, or explosive gases.
- Supervision: Never use this charger without supervision. Always monitor charging batteries.
- Power Disconnection: When not in use, always unplug the input power from the charger.
- Charging Current: When using the charging function, set a current that matches the battery's specifications. Avoid setting an excessive current to prevent battery damage. Always consult your battery manufacturer's guidelines for correct charging instructions.
3. Q4AC Layout and Components
Front View

- Display: IPS bright and clear wide-angle display.
- Scroll Wheel: Turn left or right for navigation, press for OK.
- CH/Exit Button: Channel selection and exit function.
- Output Main Port *4: Four main output ports for connecting batteries.
- Balance Port *4: Four balance ports for cell balancing during charging.
Rear View

- Micro USB Port: For firmware upgrades and PC connection.
- DC Input Port: For DC 10-18V power supply.
- Cooling Fan: For heat dissipation during operation.
- AC Input Port: For AC 100-240V power supply.
Battery Output Options

Display Features

4. Setup and Quick Start
- Connect Power Supply: Connect the AC 100-240V power cord or DC 10-18V power supply to the corresponding input port on the back of the Q4AC.
- Boot Up: The screen will display the boot logo for 2 seconds, accompanied by a startup sound.
- Main Interface: After booting, the screen enters the main interface, showing the status of the four charging channels.
- Channel Selection: Short press the [CH/Exit] button to cycle the cursor among the four channels.
- Information Display: Scroll the [Scroll Wheel] to switch between displaying the voltage and internal resistance of the selected channel.
- Start/Stop Task: Short press [OK] to select a charging task when a channel is idle. When a channel is in progress, short press [OK] to adjust or end the charge.
- System Settings: Long press [OK] to enter the system setting interface when all four channels are free.
- Exit/Confirm: Press [CH/Exit] to end modifications or return to the previous interface. Short press [Scroll Wheel] once to confirm a function. Long press [Scroll Wheel] for 2 seconds to activate the delete key function. A successful key operation will be indicated by a 'didi' sound.

5. Operating Instructions
5.1. Charging Settings
From the main interface, short press [OK] to enter the charging function. If battery selection is enabled in system settings, you can choose from 5 saved battery records. Otherwise, it defaults to the first record.
5.1.1. Battery Type Selection
Scroll the [Scroll Wheel] to select the desired battery type or create a new one. Press [OK] to confirm. The Q4AC supports:
- LiPo: Lithium Polymer (3.70V nominal, 4.20V full)
- LiHV: High-Voltage Lithium (3.85V nominal, 4.35V full)
- LiFe: Lithium Iron (3.30V nominal, 3.60V full)
- Lion: Lithium-Ion (3.60V nominal, 4.10V full)
- NiMh: Nickel-Metal Hydride (1.20V nominal)
- PB: Lead-Acid (2.00V nominal)
Important: Selecting the wrong battery type can damage the battery, charger, and pose fire hazards. Always choose carefully and follow manufacturer guidelines.
5.1.2. Number of Cells
Move the cursor to "Cells" and press [OK] to modify the number of battery cells. You can set it to "Auto" for automatic detection or manually select 1S, 2S, 3S, or 4S.
- Auto: The charger automatically identifies the cell count based on the battery voltage connected to the output port.
- Manual: Select the exact cell count (1S-4S).
Tips:
- Over-discharge or overcharge can cause cell identification errors.
- Incorrect cell count settings can lead to insufficient charging or overcharging, damaging the battery. Set carefully.
- For Lixx batteries, connecting to the balance port allows for more accurate identification of battery strings.
5.1.3. Work Mode
Move the cursor to "Mode" and press [OK] to select the work mode:
- Charge: For charging batteries.
- StoCHG (Storage Charge): For charging/discharging LiPo, LiHV, LiFe, and Lion batteries to a storage voltage.
NiMh and PB batteries only support the "Charge" mode.
5.1.4. End Voltage (TVC)
Move the cursor to "End Voltage" and press [OK] to modify the cut-off voltage for single cells. This setting is applicable only to LiPo, LiHV, and LiFe batteries.
- Charging: This is the charging cut-off voltage, adjustable within ±50mV of the full voltage.
- Discharging: This is the discharge cut-off voltage.
Adjust the value in 0.01V increments using the [Scroll Wheel].
Important: Do not modify the cut-off voltage if you are unfamiliar with battery characteristics. TVC stands for Terminal Voltage Control.
5.1.5. Charging Current
Move the cursor to "Charge Current" and press [OK] to adjust the current. The charger supports up to 5.0A. Adjust the value in 0.1A increments using the [Scroll Wheel]. Scrolling quickly will increase or decrease the value faster.
Tips: Set the charging rate to 1-2C according to the battery capacity. For example, a 2000mAh battery should be charged at 2.0-4.0A. Always refer to your battery manufacturer's instructions.
5.1.6. NiMh Setting (PeakV)
When the battery type is NiMh, you can set the negative pressure value (PeakV) for full charge detection. The setting range is 5mV-15mV.
Information: PeakV refers to the slight voltage drop that occurs when a NiMH battery is fully charged.
5.2. Charging Work
Once charging begins, the charger displays the working interface, showing real-time data for each channel including voltage, current, power, temperature, and internal resistance.
- Monitoring: Scroll the [Scroll Wheel] to switch the display of internal resistance and voltage values for the corresponding channel.
- Adjust/Stop: Short press [OK] to dynamically set the working current or stop the charging process.
- Ending Work: To end charging/discharging, move the cursor to [Stop] and short press [OK]. The charger will return to the main interface.
- Completion/Error: Upon completion or a charging error, a prompt box will appear with an audible sound.
Important: Always supervise charging to address any abnormalities safely.
Lithium Battery Balance: When charging a lithium battery, connecting only to the main port will not perform balance management. For proper balance management, ensure the battery is connected to the balance port.
Continuous Charging: After a charge is completed, unplug the battery and insert a new one. The device will automatically continue to charge/discharge according to the set mode. If a fixed cell count is set, ensure batteries with the same cell count are connected. If automatic detection is used, verify the detected cell count matches the actual number.
6. Other Functions
6.1. Firmware Upgrade
Connect the Q4AC to your computer using the USB data cable. The computer will recognize a USB drive named "Toolkit". Download the firmware upgrade file (e.g., `app.upga`) from the official ToolkitRC website. Copy and paste the new file onto the USB drive, overwriting existing files, to upgrade the firmware.
6.2. Automatically Continue Charging
This function allows the charger to automatically continue charging the next battery after one is fully charged. To activate, unplug the charged battery for 2 seconds, then connect the next battery. This feature can be enabled or disabled in the system settings menu.
6.3. Fan Level Control
- If the internal temperature exceeds 42°C, the cooling fan will operate at half-speed to reduce noise.
- If the internal temperature exceeds 50°C, the fan will operate at full-speed to enhance heat dissipation.
6.4. Manual Voltage Calibration
To manually calibrate the voltage:
- While the charger is off, press and hold the [Scroll Wheel].
- Connect the power supply while holding the [Scroll Wheel]. The system will enter the manual voltage calibration function.
- Use a voltmeter to measure the actual voltage of each battery cell.
- Move the cursor to the corresponding voltage value on the charger's display and modify it to match the voltmeter reading.
- After calibration, move the cursor to the "Save" option and short press [OK]. The charger will beep for a long time, indicating successful saving.
- Exit or shut down the charger.
6.5. Fully Charged Indication
When a lithium battery is fully charged, the charger will prompt "Fast charging has ended". If the battery remains connected, the charger will automatically perform a constant voltage trickle charge to maintain the battery's full state.
7. User Tips
- Cell Count Limitation: The Q4AC charger supports up to 4S LiPo batteries. If you use 6S batteries, this charger is not suitable for your needs.
- Efficiency: Users have noted the charger's efficiency, especially with its four independent channels, significantly reducing charging time for multiple batteries.
- Power Supply: For optimal performance and charging speed, pair the Q4AC with a robust and reliable power supply.
- Ease of Use: Many users find the product intuitive and easy to use, thanks to its clear IPS display and wheel menu navigation.
- Scroll Wheel Durability: A few users have reported potential issues with the scroll wheel after extended use. Handle with care.
8. Specifications
| Feature | Details |
|---|---|
| Input | AC100-240V@MAX1.5A, DC10-18V@MAX20A |
| Battery Type | LiPo, LiHV, LiFe, Lion@1-4S; NiMh@1-10S; Pb@1-8S |
| Balance Current | 240mA @2-4S |
| Accuracy | <0.005V |
| Charge Power (DC Input) | 0.1-5A@50W*4 |
| Charge Power (AC Input) | 0.1-5A@50W*2 (AC 100W total) or 0.1-5A@25W*4 (AC 100W total) |
| Discharge Power | 0.1-2A@5W*4 |
| USB | Upgrade@USB |
| Battery Voltage Range | 1.0V-5.0V @1-4S |
| Battery Internal Resistance | 1-100mR @1-4S |
| Display | IPS 3.5 inch, 480*320 Pixel |
| Product Size | 150mm*112mm*36.5mm |
| Product Weight | 450g |
| Individual Packing Size | 160mm*160mm*46mm |
| Individual Packing Weight | 600g |
9. Troubleshooting
- Charger Not Powering On:
- Ensure the AC or DC power input is correctly connected and providing the specified voltage (AC 100-240V or DC 10-18V).
- Check the power cable for any damage. - Battery Not Detected or Charging Error:
- Verify that the battery type and cell count settings match the connected battery. Incorrect settings can prevent charging.
- Ensure the main output and balance ports are securely connected to the battery.
- Check for any damage to battery connectors or balance leads.
- If charging a lithium battery, ensure it's connected to the balance port for proper detection and management. - Overheating:
- Ensure the cooling fan is not obstructed and is operating correctly. The fan should activate when internal temperatures exceed 42°C.
- Do not operate the charger in confined spaces or environments with poor ventilation. - Display or Navigation Issues:
- If the screen is unresponsive or the scroll wheel is not working as expected, try restarting the charger by disconnecting and reconnecting the power.
- Check system settings for backlight and buzzer configurations. - Language Settings:
- The charger supports multiple languages. To change the language, long press [OK] when all channels are free to enter System Settings, then navigate to 'Language' and select your preferred option (e.g., English, Spanish, French, Portuguese, Chinese, Japanese, Korean, German). - Firmware Update Issues:
- Ensure the `app.upga` file is correctly placed in the root directory of the charger's USB drive when connected to a PC.
- Use a reliable USB cable and ensure the connection is stable during the update process.
10. Warranty and Support
For warranty information, technical support, and service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com. You may also refer to the provided PDF user manual for additional details and contact information.
A PDF version of this manual is available for download: Download User Manual (PDF)