XIAOMI P12

Contents

Xiaomi P12 Automatic Foam Soap Dispenser User Manual

Model: P12 (Also compatible with P11, P11B, P11S, P11A series)

Brand: XIAOMI

Introduction

Thank you for choosing the Xiaomi P12 Automatic Foam Soap Dispenser. This device provides a touchless and hygienic way to dispense soap, suitable for various environments such as bathrooms and kitchens. Featuring an infrared sensor, adjustable dispense volume, and a transparent liquid window, it offers convenience and efficiency in your daily routine. This manual will guide you through the setup, operation, and maintenance of your new soap dispenser.

Xiaomi P12 Automatic Foam Soap Dispenser in black, showing its wall-mounted design and 380ml capacity.
The Xiaomi P12 Automatic Foam Soap Dispenser, available in black and white.

Safety Information

  • Do not immerse the device in water or other liquids.
  • Keep out of reach of children.
  • Use only the specified charging cable (Type-C) for charging.
  • Avoid direct sunlight or heat sources.
  • Do not use corrosive chemicals to clean the device.
  • Ensure the charging port is dry before connecting the charging cable.

Package Contents

  • Automatic Foam Soap Dispenser (P12/P11 series)
  • USB Type-C Charging Cable
  • Wall Mount Adhesive Hook
  • User Manual (this document)

Specifications

Feature Specification
Model P12 (P11/P11B/P11S/P11A)
Brand XIAOMI
Voltage <20V
Power Source Lithium battery
Capacity 380ml
Waterproof Rating IPX5
Dimensions (H x W x D) 205mm (8in) x 75mm (2.95in) x 111mm (4.37in)
Charging Port Type-C
Dispense Type Foam or Gel (model dependent)
Diagram showing the dimensions of the white soap dispenser: 205mm height, 75mm width, 111mm depth.
Product dimensions for reference.

Setup

1. Charging the Device

  1. Locate the Type-C charging port, usually on the top or side of the device.
  2. Connect the provided USB Type-C cable to the dispenser and a suitable power source (e.g., USB wall adapter, computer USB port).
  3. The indicator lights will show charging status. Ensure the device is fully charged before first use for optimal battery life.
Demonstration of charging the dispenser via its Type-C port.

2. Filling the Soap Dispenser

  1. Twist the top section of the dispenser counter-clockwise to separate it from the liquid reservoir. The dispenser features a large bottle mouth for easy refilling.
  2. Pour your desired liquid soap into the reservoir. For foam dispensers, it is recommended to mix liquid hand soap with water in a 1:4 ratio (1 part soap to 4 parts water) for optimal foam consistency.
  3. Reattach the top section by aligning and twisting clockwise until secure.
Close-up image showing liquid soap being poured into the dispenser's reservoir, highlighting the transparent window and power button.
Filling the dispenser and viewing the transparent liquid window.
Demonstration of filling the dispenser and mixing soap with water.

3. Installation (Wall-Mounted or Desktop)

The dispenser can be placed on a countertop or wall-mounted using the provided adhesive hook.

  1. **Desktop Placement:** Simply place the dispenser on a flat, stable surface near your sink.
  2. **Wall-Mounted Installation:**
    • Clean and dry the desired wall surface thoroughly.
    • Peel off the protective film from the adhesive hook.
    • Press the adhesive hook firmly onto the wall, ensuring no air bubbles, and hold for a few seconds.
    • Wait for at least 24 hours for the adhesive to fully cure before hanging the dispenser.
    • Align the dispenser with the hook and slide it down to secure it in place.
Image showing the soap dispenser both on a countertop and wall-mounted next to a sink.
The dispenser can be used on a countertop or wall-mounted.
Demonstration of wall-mounting the dispenser using the drill-free adhesive hook.

Operating Instructions

1. Power On/Off

  • To power on, press and hold the power button (located on the top of the dispenser) for a few seconds until the indicator light illuminates.
  • To power off, press and hold the power button again until the indicator light turns off.

2. Adjusting Dispense Volume

The dispenser offers four adjustable levels for soap dispense volume to suit different needs.

  • After powering on, short press the power button to cycle through the four dispense volume settings.
  • Each press will change the volume, indicated by the number of illuminated lights on the top panel.
  • Select the desired volume before use.
Demonstration of adjusting the dispense volume using the power button.

3. Automatic Dispensing

  • Once powered on and filled, simply place your hand under the nozzle.
  • The infrared sensor will detect your hand and automatically dispense the pre-set amount of soap.
  • The dispenser is available in both foam and gel types. Ensure you have the correct model for your preferred soap consistency.
Demonstration of automatic foam and gel dispensing.

Maintenance

1. Cleaning

  • Wipe the exterior of the dispenser with a soft, damp cloth.
  • Do not use abrasive cleaners or solvents, as these can damage the finish.
  • Ensure the sensor area and nozzle are kept clean for optimal performance.

2. Refilling

  • Monitor the transparent liquid window to check the soap level.
  • When the soap level is low, refill the reservoir as described in the "Filling the Soap Dispenser" section.

Troubleshooting

Problem Possible Cause Solution
Dispenser does not turn on. Low battery or not charged. Charge the device fully using the provided Type-C cable.
No soap dispensed.
  • Reservoir is empty.
  • Sensor is blocked or dirty.
  • Soap is too thick (for foam models).
  • Refill the reservoir.
  • Clean the sensor area.
  • Dilute foam soap with water (1:4 ratio).
Foam is not rich enough. Incorrect soap-to-water ratio. Adjust the soap-to-water ratio to 1:4.
Device not charging. Faulty cable or charging port. Ensure the Type-C cable is properly connected and try a different power source. Inspect the charging port for damage.

User Tips

  • For optimal foam consistency, especially with foam dispensers, always dilute liquid hand soap with water at a 1:4 ratio (1 part soap to 4 parts water).
  • Regularly check the transparent liquid window to avoid running out of soap unexpectedly.
  • Keep the sensor area clear of obstructions and clean it periodically to ensure reliable operation.
  • Experiment with the four dispense volume settings to find the perfect amount for your needs, minimizing waste.

Frequently Asked Questions (FAQ)

Q: Can I use any type of liquid soap?
A: For foam dispensers, it is recommended to use foaming hand soap or dilute regular liquid hand soap with water at a 1:4 ratio. For gel dispensers, any liquid hand soap or sanitizer can be used.
Q: Is the dispenser truly waterproof?
A: The dispenser has an IPX5 waterproof rating, meaning it is protected against low-pressure water jets from any direction. However, it should not be immersed in water.
Q: How long does the battery last on a single charge?
A: Battery life can vary depending on usage frequency and dispense volume settings. A full charge typically provides several weeks to a few months of use.

Warranty and Support

For detailed warranty information, technical support, or service inquiries, please refer to the official product documentation or contact your retailer. A comprehensive user manual in PDF format is available for download at: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.