SUMRY MPS-VIII ECO Series 3600W

Contents

SUMRY Hybrid Solar Inverter User Manual

Model: MPS-VIII ECO Series 3600W

Version: 1.0

Sumry Inverter Front View with Key Specifications

Sumry Inverter Front View: MPS-VIII ECO Series, 3600W/120VAC, 24VDC Nominal, 120A Max AC Charging Current, 60-450VDC Max DC Voltage, 50/60Hz Automatic Recognition.

1. Introduction

This manual describes the assembly, installation, operation, and troubleshooting of the SUMRY MPS-VIII ECO Series Hybrid Solar Inverter. Please read this manual carefully before installation and operation. Keep this manual for future reference.

1.1. Features

  • High-efficiency pure sine wave inverter.
  • Configurable input voltage range for home appliances and personal computers via LCD setting.
  • Configurable battery charging current based on applications via LCD setting.
  • Configurable AC/Solar Charger priority via LCD setting.
  • Compatible with mains voltage or generator power.
  • Auto restart while AC is recovering.
  • Overload, Over temperature, and Short circuit protection.
  • Smart battery charger design for optimized battery performance.
  • Cold start function.

1.2. Basic System Architecture

The inverter integrates functions of an inverter, solar charger, and battery charger to provide uninterruptible power support. It can power various appliances in home or office environments, including motor-type appliances like refrigerators and air conditioners.

Basic System Architecture Diagram

Basic System Architecture: Illustrates connection of Solar Panels (A & B), Utility Grid, Generator, Lithium Battery, the On/Off Grid Solar Inverter, WiFi Monitor, AC Loads, and Home Appliances.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  • Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  • CAUTION: To reduce risk of injury, charge only deep-cycle lead-acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  • Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  • To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  • CAUTION: Only qualified personnel can install this device with battery.
  • NEVER charge a frozen battery.
  • For optimum operation of this inverter/charger, please follow required specifications to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  • Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  • Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Refer to the INSTALLATION section of this manual for details.
  • One piece of 150A fuse is provided as over-current protection for the battery supply.
  • GROUNDING INSTRUCTIONS: This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulations to install this inverter.
  • NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  • Warning!! Only qualified service persons are able to service this device. If errors still persist after following the troubleshooting table, please send this inverter/charger back to a local dealer or service center for maintenance.

3. Setup and Installation

3.1. Unpacking and Inspection

Before installation, inspect the unit. Ensure nothing inside the package is damaged. You should have received the inverter unit and a user manual.

Video: Unboxing and Basic Setup Demonstration of the Sumry Hybrid Solar Inverter. Shows unpacking, physical overview, and initial wiring connections.

3.2. Mounting the Unit

Consider the following points before selecting where to install:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level to allow the LCD display to be read at all times.
  • For proper air circulation to dissipate heat, allow a clearance of approximately 20 cm to the side and 50 cm above and below the unit.
  • The ambient temperature should be between $0^{\circ}C$ and $55^{\circ}C$ to ensure optimal operation.
  • The recommended installation position is to be adhered to the wall vertically.
  • Be sure to keep other objects and surfaces clear to guarantee sufficient heat dissipation and space for wiring.

CAUTION: Suitable for mounting on concrete or other non-combustible surface only. Install the unit by screwing two M6 screws.

3.3. Battery Connection

For safety and regulation compliance, install a separate DC over-current protector or disconnect device between the battery and inverter. Use appropriate cable sizes for battery connection to ensure system safety and efficient operation.

Battery Connection Example

Battery Connection Example: Shows 24V battery types (GEL, FLD, LI, USE) and indicates 120A PV Max, 100A AC Max.

WARNING: Shock Hazard! Installation must be performed with care due to high battery voltage in series.

CAUTION: Before making the final DC connection or closing the DC breaker/disconnector, ensure positive (+) is connected to positive (+) and negative (-) to negative (-).

Recommended Battery Cable Size:
ModelWire SizeCable (mm²)Torque Value (max)
3.6KW/6.2KW1 x 2AWG252 Nm

3.4. AC Input/Output Connection

CAUTION: Before connecting to AC input power source, install a separate AC breaker between the inverter and AC input source. This ensures the inverter can be securely disconnected and protected from overcurrent. Recommended AC breaker: 32A for 3.6KW, 50A for 6.2KW. Do NOT mis-connect input and output connectors.

Suggested Cable Requirement for AC Wires:
ModelGaugeCable (mm²)Torque Value
3.6KW12 AWG41.2 Nm
6.2KW10 AWG61.2 Nm
Installation Knowledge Diagram

Installation Knowledge Diagram: Shows recommended circuit breaker placement between the battery pack and inverter, solar panel and inverter, grid and inverter, and inverter output and load.

3.5. PV Connection

CAUTION: Before connecting to PV modules, install a separate DC circuit breaker between the inverter and PV modules.

PV Module Selection:

When selecting PV modules, consider the following parameters:

  • Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter (500Vdc).
  • Open circuit Voltage (Voc) of PV modules should be higher than the min. battery voltage.
Inverter Model3.6KW6.2KW
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range60Vdc~450Vdc

3.6. Communication Connection

Use the supplied communication cable to connect to the inverter and a Wi-Fi module (optional). Download the APP from the APP store and refer to the

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.