KEMIMOTO B0804-03407-BK

KEMIMOTO UTV ATV Whipless LED Whip Lights Instruction Manual

Model: B0804-03407-BK

1. Introduction

Thank you for choosing KEMIMOTO UTV ATV Whipless LED Whip Lights. This manual provides detailed instructions for the proper installation, operation, and maintenance of your new LED whip lights. Please read this manual thoroughly before installation and keep it for future reference.

These LED whip lights are designed for off-road vehicles such as UTVs and ATVs, offering enhanced visibility and a customizable lighting experience with multiple color options. They are built to withstand harsh outdoor conditions.

2. Product Information

2.1 Package Contents

Before you begin installation, carefully check the package contents against the list below to ensure all items are present.

Package contents including two light pods, brackets, wiring harness, and remote control.
Figure 1: Package Contents. Includes two light pods, U-shaped brackets, pipe clamp brackets, wiring harness, remote control, and various screws/nuts.
  • Light (x2)
  • U-shaped Bracket (x2)
  • Wiring Harness (x1)
  • Remote Control (x1)
  • Pipe Clamp Bracket (x2)
  • Hexagon Screw (x4)
  • Self-tapping Screw (x3)
  • Hexagon Socket Screw (x8)
  • Nut (x4)
  • Flat Pad (x12)
  • Spring Pad (x12)
  • L-shaped Wrench (x1)

2.2 Required Tools & Estimated Time

  • 10mm Open-end Wrench (x2)
  • One-Word Screwdriver (for prying open switch panel)

Estimated Installation Time: 20-30 minutes

3. Setup and Installation

Important: Please read all instructions carefully before starting. Ensure your vehicle is clean and free of debris for easier installation. Follow the steps in the order shown for a satisfactory installation.

3.1 Wiring Diagram

Detailed wiring diagram for the LED whip lights, showing connections to control box, RF antenna, harness switch, inline fuse, and battery.
Figure 2: Wiring Diagram. Illustrates connections for the control box, RF antenna, harness switch, inline fuse, and battery terminals.

3.2 Installation Steps

  1. Prepare for Switch Installation: Use a screwdriver to carefully pry open one of the decorative panels on your vehicle's dashboard or desired location to install the rocker switch.
  2. Connect Harness Switch: Release the connector at position [B] on the wiring harness. Thread the other end of the harness switch (connector [B], red wire, and black wire) through the opening created in Step 1. Install the harness switch into the panel.
  3. Connect to Vehicle Battery: Connect the red wire of the wiring harness to the positive terminal of your vehicle's battery. Connect the black wire to the negative terminal of the vehicle's battery.
  4. Mount the Lights: Use the provided Hexagon Screws, Nuts, Flat Pads, and Spring Pads to fix the Light [1], U-shaped Bracket [2], and Pipe Clamp Bracket [5] to the round pipe of your vehicle. The pipe clamp bracket is suitable for 1.5-2 inch round pipes. Ensure the light is installed on a relatively flat or horizontal tube so the beam shines upward. Route the wiring harness to the mounting location, making sure there is enough slack for the wires to reach the light pods.
  5. Final Connection: Connect the connector at position [B] of the harness [3] to the corresponding connector on the light pods.
Diagram showing the installation of the rocker switch, battery connections, and light mounting on a roll bar.
Figure 3: Installation Overview. Shows the process of installing the switch, connecting to the battery, and mounting the lights.

4. Operating Instructions

Your KEMIMOTO LED Whip Lights can be controlled using two methods: the RF Wireless Remote Control and the Rocker Switch.

4.1 Remote Control Operation

Image of the RF Wireless Remote Controller and Rocker Switch with their respective ON/OFF and color changing functions.
Figure 4: Control Methods. Details the functions of the remote control and rocker switch.
  • ON Button: A single press will power the lights on and switch between available colors (Red, Green, Blue, White) with each subsequent click.
  • OFF Button: A single press will power the lights off.

4.2 Rocker Switch Operation

  • Lower Part (ON): Pressing the lower part of the switch will turn the lights on and cycle through the available colors (Red, Green, Blue, White) with each press.
  • Upper Part (OFF): Pressing the upper part of the switch will turn the lights off.

4.3 Visual Demonstration

Video 1: Product Demonstration. Shows the LED whip lights changing colors (red, white, blue, green) and their waterproof capabilities under simulated rain.

5. Maintenance

The KEMIMOTO LED Whip Lights are designed for durability and minimal maintenance, featuring a waterproof lens and robust aluminum housing for heat dissipation.

  • Cleaning: Periodically clean the light pods and lenses with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners that could scratch the lenses.
  • Inspection: Regularly check all mounting hardware and wiring connections to ensure they are secure. Tighten any loose screws or connections.
  • Weather Resistance: The lights are IP68 waterproof, rustproof, and dustproof, designed to withstand various outdoor weather conditions.
Image highlighting the durability features: IP68 waterproof, rustproof, dustproof, efficient cooling, and adjustable mounting bracket.
Figure 5: Durability Features. Illustrates the robust design for outdoor use, including waterproof and cooling capabilities.

6. Troubleshooting

ProblemPossible CauseSolution
Lights do not turn onLoose wiring connection
Blown fuse
Incorrect power connection		Check and secure all wiring connections.
Inspect the inline fuse (10 AMP) and replace if blown.
Verify positive and negative battery connections.
Remote control not workingDead battery in remote
Remote out of range
RF antenna disconnected		Replace the remote control battery.
Ensure remote is used within effective range.
Check connection of the RF antenna to the control box.
Lights flicker or dimLow vehicle battery voltage
Loose connection
Faulty wiring		Check vehicle battery voltage and charge if necessary.
Inspect and secure all wiring connections.
Examine wiring for damage and replace if needed.

7. Specifications

  • Color: Black
  • Voltage: 12 V DC
  • Light Source Type: LED
  • Material: Aluminum housing, Scratch-resistant Glass Lens, Stainless Steel U-shaped brackets
  • Item Weight: 2.6 kg (approx. 5.7 lbs)
  • Special Features: Waterproof (IP68), Rustproof, Dustproof, Efficient Cooling, Adjustable Mounting Bracket
  • Mounting Compatibility: Fits 1.5"-2" round roll bars/tubing

7.1 Light Output & Dimensions

Comparison table for 40W and 60W light models, showing voltage, electric current, power, luminous flux, and beam height.
Figure 6: Light Output Comparison. Details specifications for 40W and 60W light models.
Specification40W Light60W Light
VoltageDC12VDC12V
Electric Current1.75A2.8A
Power21W33.6W
Luminous Flux15480 LM17380 LM
Beam Height446m506m
UTV with whip lights in various colors (red, white, green, blue) demonstrating visibility.
Figure 7: Multi-color Light Output. Shows the lights projecting red, white, green, and blue beams.
Image showing UTV with red, white, blue, and green light beams, indicating a 4265FT visible distance at night.
Figure 8: Visible Distance. Demonstrates the 4265FT visible distance at night for various colors.

Lighting Distance by Color:

  • White Light: 446 meters
  • Green Light: 446 meters
  • Red Light: 579 meters
  • Blue Light: 379 meters

7.2 Product Dimensions

Diagram showing the dimensions of the light pods and the length of various wiring harness components.
Figure 9: Product Dimensions. Provides measurements for the light pods and wiring harness components.

Light Pod Dimensions (approximate):

  • Front Lens Diameter (40W Light): 50mm / 1.97 inches
  • Front Lens Diameter (60W Light): 70mm / 2.76 inches
  • Overall Light Pod (approx): 6.5 cm (width) x 6.5 cm (depth) x 8.2 cm (height) / 2.56 in (width) x 2.56 in (depth) x 3.23 in (height)

Wiring Harness Lengths (approximate):

  • Light to Connector: 50 cm / 19.7 inches
  • Control Box to Power Source: 157 cm / 61.8 inches
  • Control Box to Switch: 32 cm / 12.6 inches
  • Power Source to Battery Terminals: 227 cm / 89.37 inches
  • Power Source to Accessory Socket: 215 cm / 84.6 inches

8. User Tips

  • Optimal Visibility: The visibility of the light beam is highly dependent on environmental conditions. The beam will appear brightest at night with atmospheric particles such as dust, fog, haze, rain, or snow in the air.
  • Safety Precaution: While the lights are designed for outdoor use, avoid shining the beam directly into eyes, at aircraft, or directly at oncoming vehicles to prevent temporary vision impairment.
  • Versatile Mounting: In addition to the provided tube clamp brackets for UTVs with 1.5-2 inch roll cages, these lights can also be mounted on other vehicles like golf carts, trucks, pickups, ATVs, boats, and motorcycles by drilling appropriate holes.

9. Warranty and Support

KEMIMOTO products are designed and manufactured to high-quality standards. For any questions, concerns, or support needs regarding your LED whip lights, please contact the KEMIMOTO Adventure Store directly.

A digital version of this user manual (PDF) is available for download. Please refer to the product page or contact customer support for the link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.