1. Product Overview
Thank you for choosing this automotive surface trim. This product is designed to enhance the appearance and personalization of your MAZDA CX-30 (2019-2020) vehicle. Manufactured with high-quality materials and precision craftsmanship, it provides protection against scuffs and scratches. The back of the product comes with high-quality 3M automotive-grade adhesive pre-applied for easy installation, secure bonding, and damage-free removal.
This product is available as a 4-piece door sill protector set or a 1-piece trunk guard.
2. Material Description
This product is made from Stainless Steel, offering a durable, oxidation-resistant, and strong metallic texture. It effectively protects your car's paint from minor scratches and adds a sleek, decorative element to your vehicle's entry points or trunk area.
3. Setup and Installation Guide
For the best adhesive results, it is recommended to install within an ambient temperature range of 21°C - 38°C (70°F - 100°F). If the temperature is below 20°C, slightly heat the double-sided adhesive for increased stability.
3.1. Prepare the Installation Area
- Clean the Surface: Thoroughly clean the installation area on your vehicle (door sills or trunk edge) using a mild cleaner or an alcohol wipe.
- Dry the Surface: Remove all dust, oil, wax, and water spots. Ensure the surface is completely dry and clean before proceeding.

Figure 1: Ensure the surface is clean and dry before installation.
3.2. Dry Fit
- Before removing the adhesive liner, hold the trim piece up to the installation area to confirm proper fit and alignment. This step is crucial to ensure correct placement.

Figure 2: Dry fit the protectors to confirm alignment.
3.3. Apply the Trim
- Remove Liner: Carefully remove the red release liner from the 3M tape on the back of the product.
- Position and Press: Carefully position the trim piece onto the desired surface. Once aligned, press it lightly onto the surface.

Figure 3: Adhesive backing of the door sill protector.
3.4. Apply Pressure & Cure
- Firm Press: Once positioned, firmly press the entire trim piece, paying special attention to the edges and curved areas. Hold pressure for 1-2 minutes.
- Curing Time: To allow the adhesive to reach its maximum bond strength, do not wash the vehicle or expose it to rain for 72 hours after installation.

Figure 4: Example of installed door sill protector.
4. Operating and Use
These door sill protectors and trunk guard are decorative and protective accessories. Once installed, they require no further operation. They serve to enhance your vehicle's aesthetics and protect the underlying paint from scuffs, scratches, and minor impacts during entry, exit, or loading/unloading.
5. Maintenance
- During regular vehicle washing, avoid using strong alkaline cleaners on the trim pieces.
- Do not direct a high-pressure water stream directly at the edges of the trim, as this could potentially compromise the adhesive bond over time.
- Clean the stainless steel surface with a soft cloth and mild soap and water as needed to maintain its shine.
6. Troubleshooting
- Adhesion Issues: If the trim does not adhere properly, ensure the surface was thoroughly cleaned and dried, and that installation occurred within the recommended temperature range. Re-apply pressure for a longer duration.
- Repositioning: If you need to remove and reposition the trim, it is strongly recommended to use a new piece of 3M automotive-grade adhesive tape to ensure proper adhesion and prevent detachment.
7. Specifications
| Material | Stainless Steel |
| Placement on Vehicle | Door sill (4PCS set) or Trunk guard (1PC) |
| Special Features | Decoration, Scuff Protection |
| Item Weight | Approximately 0.3 kg |
| Manufacturer Part Number | 23561 |
| Country/Region of Manufacture | CN (Mainland China) |
| Package Dimensions (approx.) | Length: 55 cm, Width: 12 cm, Height: 5 cm |
| Package Weight (approx.) | 0.32 kg |
8. User Tips
- For optimal adhesion, perform installation on a warm day. Ensure both the vehicle surface and the moldings are warm. A hairdryer can be used to gently warm the moldings and adhesive before and during fitting.
- Take your time during the dry fit step to ensure perfect alignment before peeling off the adhesive backing.
- The product is well-protected during shipping; remove any protective films after installation to reveal the final finish.
9. Precautions
- Optimal Conditions: For best results, install within the recommended temperature range of 21°C-38°C to ensure optimal adhesive flow and bonding.
- Surface Consideration: If installing over paint protection film (PPF) or a vinyl wrap, test compatibility first and consider increasing the pressing time during installation.
- Avoid Excessive Heat: While warm temperatures are recommended for installation, avoid applying the trim on surfaces that have become excessively hot (e.g., over 60°C/140°F from direct sunlight), as this may overly soften the adhesive.
- Reusability: If you need to remove and reposition the trim, it is recommended to use a new piece of 3M tape to ensure proper adhesion.
- Periodic Check: Please periodically check the trim piece to ensure it is secure for safe driving.
10. Frequently Asked Questions (FAQ)
- Q: What are the dimensions of the door sills?
- A: Specific individual dimensions for each door sill piece are not provided in the product information. Please refer to the dry fit step to confirm suitability for your vehicle before permanent installation.
11. Warranty and Support
Warranty information for this product is not explicitly provided. For any support inquiries, warranty claims, or further questions, please contact the seller directly through your purchase platform.
12. Disclaimer
This product is a decorative accessory. The installation outcome depends on the cleanliness of the vehicle's surface and the installation conditions. The manufacturer is not responsible for any paint damage or product detachment resulting from improper installation. Please periodically check the trim piece to ensure it is secure for safe driving.