MEKEDE FA13A

Contents

MEKEDE Harness Fascia and Frame Kit

Model: FA13A

Brand: MEKEDE

For Fiat Ducato 2006 Car Radio Dash Matching Panel Kit Adapter Panel Cable

1. Introduction

This manual provides detailed instructions for the installation and use of the MEKEDE Harness Fascia and Frame Kit, specifically designed for the Fiat Ducato 2006 model. This kit allows for the seamless integration of a 9-inch aftermarket car radio (head unit) into your vehicle's dashboard, replacing the original factory radio. Please read these instructions carefully before beginning installation to ensure proper fitment and functionality.

2. Package Contents

Please verify that all components are present and undamaged before proceeding with installation:

  • 1 x 9-inch Radio Fascia Frame
  • 1 x Wiring Harness Adapter
  • 2 x Mounting Brackets
Contents of the MEKEDE Harness Fascia and Frame Kit
Figure 2.1: Kit components including the fascia frame, wiring harness, and mounting brackets.

3. Specifications

3.1. Dimensions

ComponentMeasurement
Fascia Frame (Top Width)228 mm
Fascia Frame (Bottom Width)218 mm
Fascia Frame (Height)130 mm
Package Length28 cm
Package Width18 cm
Package Height8 cm
Dimensions of the radio fascia frame
Figure 3.1: Detailed dimensions of the fascia frame (228mm top, 218mm bottom, 130mm height).

3.2. Weight

  • Package Weight: 0.372 kg

4. Installation Guide

Professional installation is recommended. Disconnect the vehicle's battery before starting any electrical work.

4.1. Preparing the Dashboard

  1. Carefully remove the original factory radio and any surrounding trim panels from your Fiat Ducato 2006 dashboard. Refer to your vehicle's service manual for specific removal procedures.
  2. Ensure the opening is clean and free of debris.
Before and after installation of the new head unit in a Fiat Ducato 2006 dashboard
Figure 4.1: Visual comparison of the dashboard before and after the installation of a 9-inch head unit with the MEKEDE fascia.

4.2. Assembling the Head Unit and Fascia

  1. Attach the provided mounting brackets to your new 9-inch aftermarket head unit.
  2. Carefully insert the head unit with attached brackets into the MEKEDE fascia frame. Ensure a snug and secure fit.
Diagram showing how a 9-inch head unit fits into the fascia frame
Figure 4.2: Illustration of a 9-inch head unit being integrated into the MEKEDE fascia frame.

4.3. Wiring Connections

Use the provided wiring harness adapter to connect your new head unit to the vehicle's electrical system. Match the wires according to the diagram below. If your head unit has different wiring, consult its specific manual.

Close-up of the wiring harness connector
Figure 4.3: Detail of the wiring harness connector (P1).
Wiring diagram for the MEKEDE harness adapter, showing pin assignments for power, ground, speakers, ACC, illumination, reverse, and steering wheel controls.
Figure 4.4: Comprehensive wiring diagram for the harness adapter.

Wiring Pin Assignments (P1 Connector):

PinFunction
A1GND (Ground)
A2B+ (Battery Positive)
A3ACC Key Switch (Accessory Power)
A4ILL small lights detecting (Illumination)
A5Reverse detecting line
A6Steering wheel control study -2
A7Steering wheel control study -1
A8ANT power (Antenna Power)
A9Speaker Front Right FR-
A10Speaker Rear Left RL-
A11Speaker Front Right FR+
A12Speaker Rear Left RL+
A13Speaker Front Left FL-
A14Speaker Rear Right RR+
A15Speaker Front Left FL+
A16Speaker Rear Right RR-

4.4. Final Installation

  1. Connect the wiring harness adapter to the vehicle's factory harness.
  2. Carefully slide the assembled head unit and fascia into the dashboard opening until it clicks into place. Ensure no wires are pinched.
  3. Reconnect the vehicle's battery.
  4. Test the new head unit's functionality, including power, audio, steering wheel controls, and any other connected features.

5. Operating Your New Head Unit

This kit provides the necessary components to install an aftermarket 9-inch head unit. The operation of the head unit itself will depend on the specific model you have installed. Please refer to the instruction manual provided with your aftermarket head unit for detailed operating instructions.

The MEKEDE harness adapter ensures that essential vehicle functions like power, ground, speaker outputs, accessory power, illumination, reverse signal, and steering wheel controls are properly connected to your new head unit.

6. Care and Maintenance

  • Cleaning: Use a soft, dry cloth to clean the fascia frame. Avoid abrasive cleaners or solvents that could damage the finish.
  • Inspection: Periodically check the connections of the wiring harness to ensure they remain secure.
  • Environmental Conditions: The fascia and harness are designed for automotive interior use. Avoid exposure to extreme temperatures or direct sunlight for prolonged periods, which could cause material degradation.

7. Troubleshooting

If you encounter issues after installation, consider the following common problems and solutions:

  • Head Unit Not Powering On:
    • Check the B+ (A2) and ACC (A3) connections on the wiring harness. Ensure they are receiving power.
    • Verify the GND (A1) connection is secure.
    • Check the fuse for the head unit and the vehicle's accessory circuit.
  • No Sound from Speakers:
    • Confirm all speaker wires (FL+, FL-, FR+, FR-, RL+, RL-, RR+, RR-) are correctly connected to the head unit and not shorted.
    • Ensure the head unit's amplifier is enabled and volume is up.
  • Steering Wheel Controls Not Working:
    • Verify the Steering Wheel Control wires (A6, A7) are correctly connected to your head unit's SWC input.
    • Most aftermarket head units require programming or 'learning' of the steering wheel controls. Refer to your head unit's manual for this procedure.
  • Illumination Not Working:
    • Check the ILL (A4) connection. This wire typically dims the head unit's display when headlights are on.
  • Reverse Camera Not Activating:
    • Ensure the Reverse Detecting Line (A5) is correctly connected to the head unit's reverse input and receives a signal when the vehicle is in reverse.

8. User Tips

  • Vehicle Compatibility: Always double-check that this kit (Model FA13A) is compatible with your specific vehicle model and year, particularly the Fiat Ducato 2006, to ensure a perfect fit and proper electrical integration.
  • Head Unit Size: This fascia is designed for 9-inch aftermarket head units. Confirm your chosen head unit's screen size before purchasing.
  • Professional Help: If you are unsure about any part of the installation, especially the electrical wiring, it is highly recommended to seek assistance from a qualified car audio installer.

9. Warranty and Support

For any questions regarding the MEKEDE Harness Fascia and Frame Kit, please contact MEKEDE customer support. You may also find additional information and detailed diagrams in the official user manual PDF, which can be accessed here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.