1. Introduction
This manual provides detailed instructions for the assembly, installation, operation, and troubleshooting of your PowMr 140A MPPT Solar Charge Controller. Please read this manual carefully before installation and operation, and keep it for future reference. It includes safety guidelines, installation procedures, and wiring information.
1.1. Features
- Configurable battery charging current based on applications via LCD setting.
- Over temperature protection.
- Smart battery charger design for optimized battery performance.
- Cold start function.
1.2. Basic System Architecture
The PowMr 140A MPPT Solar Charge Controller integrates solar power from PV modules to charge external battery packs.
1.3. Product Overview
The controller features a comprehensive LCD display and intuitive function buttons for easy operation and monitoring.

Figure 1: PowMr 140A MPPT Solar Charge Controller (POW-48140A)
The controller supports a 48V system with a 140A charge current, a PV array voltage range of 60-450VDC, and is compatible with various battery types.
2. Safety Instructions
WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.
- Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
- CAUTION - To reduce risk of injury, charge only deep-cycle lead-acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
- Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
- To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
- CAUTION - Only qualified personnel can install this device with battery.
- NEVER charge a frozen battery.
- For optimum operation, select appropriate cable size as specified.
- Be very cautious when working with metal tools on or around batteries. Dropping a tool can cause sparks, short circuits, or explosions.
- Strictly follow installation procedures when disconnecting DC terminals.
- One 150A fuse is provided for over-current protection for the battery supply.
- NEVER cause DC input short-circuited.
- Warning!! Only qualified service persons are able to service this device.
3. Installation
3.1. Unpacking and Inspection
Before installation, inspect the unit for any damage. The package should contain:
- The PowMr 140A MPPT Solar Charge Controller unit (x1)
- User Manual (x1)
3.2. Preparation
Before connecting any wirings, remove the port cover by unscrewing it.
3.3. Mounting the Unit
Consider the following points when selecting a mounting location:
- Do not mount on flammable construction materials.
- Mount on a solid surface.
- Install at eye level for easy LCD display reading.
- Allow approx. 20 cm clearance on sides and 50 cm above/below for air circulation.
- Ambient temperature should be between $0^{\circ}C$ and $55^{\circ}C$.
- Mount vertically on the wall.
- Ensure sufficient heat dissipation and space for wiring.
SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.
Install the unit by screwing two M6 screws securely into the wall.
Video: POW-48140A Solar Charge Controller Wiring Guide. Shows mounting the controller, removing the port cover, connecting battery, connecting PV array, and powering on the system.
4. Connection
4.1. Battery Connection
Recommended battery cable size:
| Model | Wire Size | Cable(mm²) | Torque value (max) |
|---|---|---|---|
| 24V/140A 48V/140A | 1 x 2AWG | 25 | 2 Nm |
CAUTION:
- Install a separate DC over-current protector or disconnect device between battery and charger.
WARNING:
- All wiring must be performed by qualified personnel.
- Use appropriate cable for battery connection to ensure system safety and efficient operation.
Steps for Battery Connection:
- Remove 18 mm insulation sleeve from positive and negative conductors.
- Apply bootlace ferrules to wire ends for secure connection.
- Connect battery packs according to the system voltage (24V or 48V).
- Insert battery wires into connectors and tighten bolts to 2 Nm. Ensure correct polarity.
4.2. PV Connection
Recommended PV cable size:
| Model | Wire Size | Cable(mm²) | Torque value (max) |
|---|---|---|---|
| 24V/140A 48V/140A | 1 x 12AWG | 4 | 1.2 Nm |
CAUTION:
- Install a separate DC circuit breaker between the charger and PV modules.
WARNING:
- Use appropriate cable for PV module connection.
PV Module Selection:
Consider these parameters:
- Open circuit Voltage (Voc) of PV modules must not exceed max. PV array open circuit voltage of charger (500Vdc).
- Open circuit Voltage (Voc) of PV modules should be higher than min. battery voltage.
- PV Array MPPT Voltage Range: 60Vdc~450Vdc.
- PV Wire Size: 12AWG.

Figure 2: Solar Panel Specifications and PV Module Selection Guide
Steps for PV Module Wire Connection:
- Remove 10 mm insulation sleeve from positive and negative conductors.
- Apply bootlace ferrules to wire ends.
- Check correct polarity. Connect positive (+) of connection wire to positive (+) of PV input connector, and negative (-) to negative (-).
4.3. Final Assembly
After connecting all wirings, replace the port cover and secure it with screws.
5. Operation
5.1. Operation and Display Panel
The front panel features an LCD display, two indicators (CHG, FAULT), and four function keys (ESC, UP, DOWN, ENTER).

Figure 3: Large LCD Screen and Function Buttons
LED Indicators:
- CHG (Green): Solid On (Battery fully charged), Flashing (Battery charging).
- FAULT (Red): Solid On (Fault occurs), Flashing (Warning condition occurs).
Function Keys:
- ESC: Exit setting mode.
- UP: Go to previous selection.
- DOWN: Go to next selection.
- ENTER: Confirm selection or enter setting mode.
5.2. LCD Settings
Press and hold ENTER for 3 seconds to enter setting mode. Use UP/DOWN to navigate and ENTER to confirm/exit. Settings include maximum charging current (10-140A), battery type (AGM, Flooded, User-Defined), auto-restart, bulk charging voltage, floating charging voltage, and battery equalization parameters.
5.3. Display Information
The LCD display shows various information by pressing UP/DOWN keys, including PV voltage, charging current, charging power, battery voltage, and main CPU Version.
5.4. Fault Reference Code
The controller displays specific fault codes for various issues, such as fan lock, over-temperature, battery voltage too high/low, bus voltage too high/low, over-current, current sensor failure, and PV voltage over limitation.
5.5. Warning Indicator
Warning codes indicate conditions like battery equalization (E9) or battery not connected (bP).
6. Battery Equalization Description
Equalization reverses negative chemical effects like stratification and removes sulfate crystals, prolonging battery life. It is recommended to equalize batteries periodically.

Figure 4: Three-Stage Charging (Boost, Bulk, Float, Equalization) and MPPT Charging Mode
How to Apply Equalization:
- Enable battery equalization in LCD setting program 05.
- Set equalization interval in program 35, or activate immediately in program 36.
When to Equalize:
The controller enters the Equalize stage when the set interval is reached or activated manually. Equalization charge is recommended once a month.
7. Maintenance
7.1. Clearance and Maintenance for Anti-Dust Kit
The charger comes with a pre-installed anti-dust kit to protect against dust and enhance reliability.
Cleaning Procedure:
- Loosen the screw on top of the charger (counter-clockwise).
- Remove the dustproof case and take out the air filter foam.
- Clean the air filter foam and dustproof case.
- Re-assemble the dust-kit back to the charger.
NOTICE: The anti-dust kit should be cleaned from dust every one month.
8. Specifications
8.1. MPPT Solar Charging Mode
| Parameter | 24V System | 48V System |
|---|---|---|
| Max. PV Array Power | 4200W | 6500W |
| Nominal PV Voltage | 180Vdc | 280Vdc |
| PV Array MPPT Voltage Range | 60Vdc~450Vdc | |
| Max. PV Array Open Circuit Voltage | 500Vdc | |
| Max Charging Current | 140Amp | |
8.2. Physical Specifications
- Dimensions: 435 x 310 x 180 mm
- Net Weight: 6.5 kg

Figure 5: Key Specifications of the 140A MPPT Charge Controller

Figure 6: Compatible Battery Types (GEL, FLD, AGM, LiFePO4, Sealed Lead-acid)
9. Troubleshooting
| Problem | Explanation / Possible Cause | What to Do |
|---|---|---|
| Unit shuts down during startup | Battery voltage too low (<1.91V/Cell) | Re-charge or replace battery. |
| No response after power on | Battery voltage too low (<1.4V/Cell) or internal fuse tripped | Re-charge/replace battery or contact service for fuse replacement. |
| Red LED on (Fault code 02) | Internal temperature over $70^{\circ}C$ | Check air flow, reduce ambient temperature. |
| Red LED on (Fault code 03) | Battery is over-charged or voltage too high | Return to repair center or check battery specs. |
| Red LED on (Fault code 01) | Fan fault | Replace the fan. |
| Red LED on (Fault code 52) | Bus voltage too low | Restart unit; if issue persists, return for repair. |
10. User Tips
No specific user tips were available from the provided buyer reviews or Q&A content for this product.
11. Warranty and Support
For technical support, warranty claims, or service inquiries, please contact PowMr directly:
- Tel/Fax: +86 755-28219903
- Email: support@powmr.com
- Website: www.powmr.com
- Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China