1. Product Overview
The LTWOO R7 is a mechanical 2x10 speed road bicycle groupset designed for efficient and reliable gear shifting. This groupset includes dual control levers (shifters), a front derailleur, and a rear derailleur, providing a complete solution for your road bike's drivetrain.

Figure 1: Complete LTWOO R7 2x10 Speed Road Groupset including shifters, rear derailleur, and front derailleur.
2. Safety & Warnings
Please read all instructions carefully before installation and use to ensure safety and prevent damage to the components or injury.
- Keep all small parts and tools out of reach of children.
- Always wear appropriate safety gear when working on bicycles.
- Ensure all bolts are tightened to the manufacturer's recommended torque specifications. Overtightening or undertightening can lead to component failure.
- If you are unsure about any installation step, consult a professional bicycle mechanic.

Warning: Keep components and tools away from children under 3 years old. Suitable for users aged 6 and above with adult supervision for installation.
3. Setup & Installation
This section provides general guidance for installing the LTWOO R7 groupset components. Specific frame requirements may vary.
3.1 Dual Control Levers (Shifters) Installation
- Mounting: Slide the shifter clamp onto the handlebar. Position the levers for comfortable reach and braking. Tighten the clamp bolt securely.
- Brake Cable Routing: Route the brake cable from the lever through the handlebar tape and to the brake caliper. Secure the cable.
- Shift Cable Routing: Route the shift cable from the lever through the handlebar tape, frame guides, and to the respective derailleur.

Figure 2: LTWOO R7 Dual Control Levers (Shifters).
3.2 Front Derailleur Installation
The LTWOO R7 front derailleur is available in two mounting types: Clamp Band and Brazed-On (Direct Mount).
3.2.1 Clamp Band Mount Front Derailleur
- Mounting: Open the clamp band and position it on the seat tube, ensuring the outer cage plate is parallel to the large chainring. The bottom of the outer cage should be 1-3mm above the teeth of the large chainring.
- Tighten: Securely tighten the clamp bolt. Use the provided spacer if adapting to a smaller seat tube diameter (e.g., 31.8mm with a 34.9mm clamp).
- Cable Connection: Route the front derailleur shift cable and connect it to the cable fixing bolt. Ensure proper cable tension.

Figure 3: LTWOO R7 Front Derailleur (Clamp Band Mount).
3.2.2 Brazed-On (Direct Mount) Front Derailleur
- Mounting: Attach the derailleur directly to the braze-on tab on your frame. Ensure the outer cage plate is parallel to the large chainring and 1-3mm above its teeth.
- Tighten: Securely tighten the mounting bolt.
- Cable Connection: Route the front derailleur shift cable and connect it to the cable fixing bolt. Ensure proper cable tension.

Figure 4: LTWOO R7 Front Derailleur (Brazed-On Mount).
3.3 Rear Derailleur Installation
- Mounting: Screw the rear derailleur directly into the derailleur hanger on your frame. Ensure it is fully seated and tighten securely.
- Chain Installation: Install the bicycle chain, ensuring it is routed correctly through the derailleur's guide and tension pulleys.
- Cable Connection: Route the rear derailleur shift cable and connect it to the cable fixing bolt. Ensure proper cable tension.
- Limit Screw Adjustment: Adjust the High (H) and Low (L) limit screws to prevent the chain from overshifting off the smallest and largest cogs of the cassette.
- B-Tension Adjustment: Adjust the B-tension screw to set the proper distance between the upper guide pulley and the cassette cogs.

Figure 5: LTWOO R7 Rear Derailleur.
4. Operating Instructions
The LTWOO R7 groupset uses dual control levers for both braking and shifting.
4.1 Shifting Gears
- Rear Derailleur (Right Lever):
- To shift to a larger cog (easier gear): Push the main lever blade inwards.
- To shift to a smaller cog (harder gear): Push the smaller lever blade inwards.
- Front Derailleur (Left Lever):
- To shift to the larger chainring: Push the main lever blade inwards.
- To shift to the smaller chainring: Push the smaller lever blade inwards.
Always shift gears while pedaling forward with moderate pressure. Avoid shifting under heavy load to prevent damage to the drivetrain components.
5. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your groupset.
- Cleaning: Regularly clean your derailleurs, chain, and shifters with a bicycle-specific degreaser and brush. Wipe down components with a soft, lint-free cloth.
- Lubrication: After cleaning, lubricate your chain with appropriate bicycle chain lubricant. Apply a small amount to pivot points on derailleurs as needed.
- Cable Inspection: Periodically check shift and brake cables for fraying, corrosion, or stiffness. Replace worn cables promptly.
- Bolt Torque: Periodically check that all mounting bolts (derailleurs, shifters) are tightened to their recommended torque specifications.
- Storage: Store your bicycle in a dry place, away from extreme temperatures and direct sunlight, to prevent corrosion and material degradation.
6. Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Poor or slow shifting | Incorrect cable tension, dirty/worn cables, misaligned derailleur, bent derailleur hanger. | Adjust cable tension using barrel adjusters, clean/replace cables, check derailleur alignment, inspect hanger. |
| Chain rubs on front derailleur cage | Incorrect front derailleur height/angle, limit screw adjustment, cable tension. | Adjust front derailleur position, fine-tune limit screws, adjust cable tension. |
| Chain falls off cassette (rear) | Incorrect limit screw adjustment (H or L), bent derailleur hanger. | Adjust H/L limit screws, check and straighten/replace derailleur hanger. |
For persistent issues, it is recommended to consult a professional bicycle mechanic.
7. Specifications
| Component | Specification |
|---|---|
| Brand | LTWOO |
| Model | R7 |
| Groupset Type | Mechanical Derailleur System |
| Gears | 2x10 Speed (20 Speed) |
| Material | Alloy |
| Dual Control Levers (Shifters) - Model: ST-R5110-10 | |
| Speed | 10S (Right), 2S (Left) |
| Brake Lever Material | Aluminium |
| Braking Mode | Cable actuation |
| Weight (Right) | 268g |
| Shift Wire Length | 2100mm |
| Front Derailleur (Clamp Band Mount) - Model: FD-R5010-C | |
| Speed | 2S |
| Mounting | Clamp Band 34.9mm (with 31.8mm spacer) |
| Operation Mode | Dual Pull |
| Max Gear Range | 56T |
| Capacity | 16T |
| Chainline | 43.5mm |
| Weight | 131g |
| Front Derailleur (Brazed-On Mount) - Model: FD-R5010-D-T | |
| Speed | 2S |
| Mounting | Direct (Brazed-On) |
| Operation Mode | Dual Pull |
| Max Gear Range | 56T |
| Capacity | 16T |
| Chainline | 43.5mm |
| Weight | 101.5g |
| Rear Derailleur | |
| Speed | 10S |
| Max Cog Size | 32T |
| Total Capacity | 23-32T |

Figure 6: Shifter Specifications Diagram.

Figure 7: Front Derailleur (Clamp Band) Specifications Diagram.

Figure 8: Front Derailleur (Brazed-On) Specifications Diagram.

Figure 9: Rear Derailleur Specifications Diagram.
8. User Tips
- The LTWOO R7 groupset offers good quality and is well-suited for new bike builds or as an upgrade for budget-conscious projects.
- Components are generally solid and perform reliably when installed correctly.
- Ensure proper cable tension and derailleur alignment during installation for the best shifting performance.
9. Manufacturer & Support Information
For technical support, warranty claims, or further inquiries, please contact the manufacturer directly:
- Manufacturer: Xiamen Yantaizheng Industry and Trade Co., Ltd.
- Address: Room 902, Building 3, No. 455, Erhuan South Road, Tongan District, Xiamen, Fujian, China
- E-mail: ray@zrace.cn
- Telephone: +86 0592-7777081
- EU Authorized Representative: TOCYA TRADING, 79 rue de patay, 75013, Paris (E-mail: TOCYATRADING75013@outlook.com)
Please retain your proof of purchase for any warranty-related claims.
10. Disposal & Recycling
Please dispose of packaging materials and old components responsibly according to local regulations. Many components are recyclable.

Figure 10: French recycling guidelines for packaging materials.

Figure 11: Product compliance markings (CE, UKCA, FCC, RoHS).