AnyTone AT-6666Pro

Contents

Anytone AT-6666Pro 10 Meter Radio User Manual

Model: AT-6666Pro | Brand: AnyTone

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Anytone AT-6666Pro 10 Meter Radio. Please read this manual thoroughly before using the radio to ensure proper function and to maximize your operating experience.

Anytone AT-6666Pro 10 Meter Radio with microphone and a truck in the background

Figure 1: Anytone AT-6666Pro 10 Meter Radio

2. Functions & Features

The Anytone AT-6666Pro is equipped with a wide range of features to enhance your communication experience:

List of 31 features for the Anytone AT-6666Pro radio

Figure 2: Key Features of AT-6666Pro

  1. LCD display with 7 color options and back light dimming
  2. FM, AM, USB, LSB, CW, PA modes
  3. Frequency Tuning Steps: 10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz
  4. ± 500Hz, 5KHz Clarifier (R/T/R+T selectable)
  5. Flexible menu functions and PC programming software
  6. RX and TX NRC Noise Reduction
  7. SQ, ASQ Function (FM and AM mode)
  8. RF GAIN Adjustment
  9. RF PWR Adjustment
  10. VFO / BAND / Memory Channel Modes
  11. Repeater Shift / Offset Frequency Function
  12. CTCSS/DCS with RX/TX Split functions
  13. SCAN Function
  14. NB/ANL Function
  15. DW DUAL-WATCH Function
  16. SWR, S/RF meter Function
  17. TOT function
  18. HI-CUT Function
  19. EMG CALL
  20. SWR Protection
  21. Power Supply Voltage Protection
  22. Key-Lock Function
  23. DTMF Function
  24. BEEP Prompt
  25. Enhanced VOX Function (VOX.SPK can support digital mode operation)
  26. ECHO Function
  27. Programmable RB Function
  28. AM TX NPC
  29. User Defined (PF) key on microphone
  30. Audio path select
  31. +10KHz Function

3. Package Contents

Please check the package contents carefully upon unpacking. If any items are missing or damaged, contact your dealer immediately.

Diagram showing the Anytone AT-6666Pro radio, microphone, mounting bracket, screws, pads, adjusting screws, microphone hanger, adhesive case protectors, and fuse.

Figure 3: Standard Accessories

  • AT-6666 10 Meter CB Radio
  • Microphone
  • Rubber Pad
  • Mounting Bracket
  • Fuse (15A 250V)
  • Screw Pack
  • Microphone Holder
  • Mounting Bracket Screws

4. Setup

4.1. Installation Location

Choose a suitable location for installation. If installing in a vehicle, ensure the radio does not obstruct the driver or passengers. Securely mount the radio and all accessories.

4.2. Antenna Installation

An efficient and resonant antenna is crucial for optimal communication performance. This radio requires an antenna impedance of 50 ohms, unbalanced.

  1. Screw the antenna connector into the antenna jack.
  2. Grounding of the antenna system is recommended for best performance.

WARNING:

  • NEVER transmit without a connected resonant antenna, or a suitable 50 ohm load being connected. Damage to the radio may result.
  • To reduce the risk of electric shock or radio damage, base station installations should include lightning protection devices.
  • Consult your authorized dealer or service center for available antenna options.

4.3. Power Connection

This radio requires a 13.8V (12V) DC power supply. Do not connect directly to a 24V DC battery system.

  1. Connect the positive (red) power cable to the + terminal of the battery.
  2. Connect the negative (black) power cable to the - terminal of the battery.

Important Notes:

  • Locate the power cable away from high temperature, moisture, and other electrical systems. Ensure it is installed where it cannot be damaged.
  • It is not recommended to use a vehicle cigar/cigarette lighter socket to power the radio, as it may not supply the correct voltage or current.
  • Do not remove the fuse holder from the cable.

4.4. Replacing Fuse

This radio requires a 15A, 250V fuse. If the fuse blows, determine the cause, correct the problem, and then replace the fuse. If new fuses continue to blow, disconnect the power cable and contact your authorized dealer.

  1. Pull the two fuse cover in opposite directions and open it.
  2. Replace the blown fuse with a new one, and close the fuse holder.
  3. Be sure to only use the correct fuse type, otherwise damage may occur.

4.5. Install Microphone Hanger

Choose a location that will not interfere with the driver. Use the supplied self-tapping screws and pads to install the hanger.

4.6. Install External Speaker

If using an external speaker, choose an 8 ohm speaker with a 3.5mm mono (double cable) TS type plug.

  1. Locate the external speaker in a suitable place.
  2. Plug into the speaker jack.

5. Getting Acquainted

5.1. Front Panel

Familiarize yourself with the controls and indicators on the front panel:

No. Key Functions
1FUNCFunction / Menu key
2MODESwitch Mode: FM, AM, USB, LSB, CW, PA
3BANDSwitch Band: A-I / VFO mode
4SCANScan / Scan add / Scan delete
5MEMUse, Store or Delete memory channels
6TSQActivate / deactivate the CTCSS/DCS function
7NRCActivate / deactivate the NRC function
8EMGEmergency Channel; Keypad lock
9PWRRF Power Control
10RFGRF Gain Control
11SQSquelch Control
12CLARSSB/CW Clarifier Control
13VOL/OFFPower On/Off; Volume Control
14CH/PUSHChannel Switch; PUSH key
15--RX/TX Indicator
16--Microphone Jack
17--LCD Display

5.2. Rear Panel

The rear panel includes connectors for PC cable, external speaker, and antenna.

No. Functions
18PC Cable Jack
19External Speaker Jack
20Antenna Jack

5.3. Microphone

The microphone features a 6-pin connector and includes UP, DOWN, PTT, and a User Defined (PF) key.

5.4. LCD Display

The LCD display provides visual feedback on the radio's status and settings. Key indicators include:

No. Indicator Description
1TXAppears during transmit (TX)
2MMMDisplays the working mode
3EMGAppears when using Emergency channels
4MEMAppears when using Memory channels
5ECHOAppears when Echo function is ON
6REPAppears when Repeater Offset function is ON
7HICAppears when Hi-Cut function is ON
888Displays the channel number
9NB/ANLAppears when Noise Blanker / ANL is ON
10Displays the Band name
1110KAppears when +10Khz function is ON
12Appears when the Roger Beep function is ON
13RFDisplay of the TX/RX signal strength
14aNot in use
15Appears when the VOX function is ON
16SCAppears when the Scan function is ON
17Appears when the Keypad Lock function is ON
18RTAppears when the SSB/CW clarifier is enabled
19SWRAppears when the SWR level indication is enabled
20DWAppears when Dual Watch function is ON
21RnrAppears when NRC Noise Reduction function in ON
22AQAppears when ASQ is enabled
23DCSAppears when DCS is enabled
24CTCAppears when CTCSS is enabled
25Displays the Frequency and Channel information

6. Operating Instructions

6.1. OFF/ON Radio & Volume Control

  1. Turn the VOL knob clockwise to switch the radio ON. A beep may sound if enabled. The LCD will display frequency or channel.
  2. Turn the VOL knob anti-clockwise to switch the radio OFF.
  3. When ON, turning VOL clockwise increases volume; anti-clockwise decreases it. Adjust for a suitable listening level.

6.2. RF Power Control

When transmitting, turn the PWR outer shaft to adjust power. Clockwise increases power, anti-clockwise reduces it.

6.3. RF Gain Control

When receiving, turn the RFG inner shaft to adjust RF gain. Clockwise increases gain, anti-clockwise reduces it.

6.4. SQUELCH Control

When the radio is in standby, turn the SQ outer shaft clockwise to adjust the squelch level (1-36 levels). The LCD displays "SQ: XX".

6.5. SSB Clarifier Control

When transmitting or receiving, turn the CLAR inner shaft to adjust USB/LSB/CW TX or RX frequency. Clockwise increases frequency, anti-clockwise reduces it.

6.6. Channel Selection

In channel mode, turn the channel knob to select the desired channel. Clockwise increases, anti-clockwise reduces the channel number.

6.7. Frequency Control

  1. In channel mode, press the [PUSH] key to temporarily adjust the VFO frequency.
  2. When the frequency is flashing, press [PUSH] again to adjust the frequency step size.
  3. When the desired frequency digit/step is flashing, turn CH clockwise to increase frequency, or anti-clockwise to reduce frequency.

Note: In channel mode, changing the VFO frequency is temporary and not saved to memory. The frequency will return to the default programmed channel after changing channels.

6.8. Keypad Functions

6.8.1. MEM (Memory Channels)

  • Using: Short press MEM to enter memory channel, turn CH to select M1-M99. Short press MEM again to exit.
  • Store: Select frequency, hold MEM until channel number flashes. Turn CH to select location, hold MEM again until flashing stops.
  • Delete: In memory mode, hold MEM for 2 seconds until channel number flashes. Turn CH to select channel, hold MEM again until flashing stops.

6.8.2. ANL/NB (Automatic Noise Limiter / Noise Blanker)

Press FUNC + [NB/ANL] to enable/disable. The "NB/ANL" icon appears on the LCD.

6.8.3. MODE or DIM

  • MODE: Short press MODE to cycle through FM-AM-USB-LSB-CW-PA.
  • DIM: Press FUNC + MODE to adjust backlight dimmer/brightness.

6.8.4. BAND or COLOR

  • BAND: Short press BAND to select band A-I.
  • COLOR: Press FUNC + BAND to switch LED backlight color.
  • VFO: Long press BAND to turn on VFO function. LCD displays "VF".

6.8.5. SCAN or DW (Dual Watch)

  • SCAN: Short press SCAN to start/stop scan. "SC" flashes. Turn CH to change scan direction.
  • Add/Delete Scan List: In channel mode, long press SCAN for 2 seconds. "SC" indicates added, no "SC" indicates not added.
  • DW: Press FUNC + SCAN to turn Dual Watch ON/OFF. LCD displays "DW".

6.8.6. TSQ or HI-CUT

  • TSQ: Short press TSQ to turn CTCSS/DCS ON/OFF. Long press TSQ to enter CTCSS/DCS settings.
  • HI-CUT: Press FUNC + TSQ to turn HI-CUT ON/OFF. LCD displays "HIC".

6.8.7. NRC or SPLIT

  • RX NRC: Short press NRC to turn RX noise reduction ON/OFF.
  • TX NRC: Short press [PTT] + NRC to turn TX noise reduction ON/OFF.
  • NRC Level: Long press NRC to enter noise reduction level setting menu.
  • SPLIT: Press FUNC + NRC to turn SPLIT function ON/OFF. LCD displays "REP".

6.8.8. EMG (Emergency Channel)

  • Short press EMG to use Emergency channel. LCD displays "EMG".
  • Press EMG once for CH9, again for CH19, and a third time to return to the last normal channel.
  • Keypad Lock: Long press EMG to lock/unlock keys. LCD displays "". Only PTT is valid when locked.

6.9. Menu Operations

The radio features several menu systems for advanced configuration:

  • Channel Function Menu: Access by pressing FUNC, then [PUSH].
  • Public Data Function Menu: Hold [PUSH] for 2 seconds.
  • Background Function Menu: Hold [MENU] for 2 seconds.
  • Self Define PF Key: Access via Background Function menu #35 PF.KEY.

For detailed settings within each menu, please refer to the specific tables and instructions in the full PDF manual.

7. Maintenance

To ensure the longevity and optimal performance of your Anytone AT-6666Pro radio, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the radio's exterior. Do not use harsh chemicals or solvents.
  • Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
  • Connections: Periodically check all cable connections (power, antenna, microphone) to ensure they are secure and free from corrosion.
  • Antenna: Ensure your antenna system is well-maintained and properly tuned. A damaged or poorly tuned antenna can affect performance and potentially damage the radio.

8. Troubleshooting

If you encounter issues with your AT-6666Pro, refer to the following common problems and solutions:

Problem Possible Cause Solution
Radio does not power onNo power, blown fuse, incorrect wiringCheck power connections, replace fuse (15A 250V), verify wiring polarity.
No audio from speakerVolume too low, squelch too high, external speaker connectedIncrease VOL, decrease SQ, check external speaker connection.
Poor transmission/receptionAntenna issue, incorrect mode/frequency, low power settingCheck antenna connection and SWR, verify mode and frequency, increase RF PWR.
Excessive noiseNB/ANL off, high RF gain, external interferenceActivate NB/ANL, reduce RFG, identify and mitigate interference sources.
Keypad lockedKeypad lock activatedLong press EMG key to unlock.

If the problem persists after trying these solutions, please consult your authorized dealer or a qualified service technician.

9. Specifications

Dimensional drawing of the Anytone AT-6666Pro radio showing length, width, and height.

Figure 4: AT-6666Pro Dimensions

General
Frequency Range28.000-29.700MHz (Programmable)
Frequency BandA/B/C/D/E/F/G/H/I + VFO
Channel40 channels (programmable) in each band
Frequency ControlPhase-Locked-Loop Synthesizer
Frequency Step10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz
Frequency Tolerance±5.0 ppm
Temperature Range-20°C ~ +50°C
MicrophoneWith Push-to-Talk / UP / DN / PF and coiled cord
Input Voltage13.8V DC
Dimensions (in mm)252(L) x 158(W) x 48(H)
Weight1.27kg
Antenna ConnectorUHF, SO239
Transmitter
Power OutputAM: 80W(PEP) / FM:50W / SSB: 80W(PEP)
Drain15A (with modulation)
ModulationFM/AM/USB/LSB/CW
Inter-modulation DistortionSSB: 3rd order, more than -25dB; 5th order, more than -35dB
SSB Carrier Suppression55dB
Unwanted Sideband50dB
Frequency ResponseAM/FM: 300 to 3000Hz
SSB: 450 to 2500Hz
Output Impedance50ohms, unbalanced
Receiver
SensitivitySSB: 0.25µV for 10dB(S+N)/N
AM: 1.0µV for 10dB(S+N)/N
FM: 1.0µV for 20 dB (S+N)/N
(All at greater than 1/2 watt of audio output)
Adjacent-Channel SelectivityAM/FM: 60dB SSB: 70dB
Image RejectionMore than 65dB
IF FrequencyAM/FM: 10.695MHz 1st IF, 455KHz 2nd IF
SSB: 10.695MHz
RF Gain Control45dB adjustable for optimum signal reception
Automatic Gain Control(AGC)Less than 10dB change in audio output for inputs from 10 to 100,000 microvolt.
SquelchAdjustable; threshold less than 1.0µV.
Automatic Squelch Control (AM/FM) 1.0µV
Audio Output Power3 watts into 8 ohms
Frequency ResponseAM/FM: 300 to 3000Hz SSB: 450 to 2500Hz
Built-in Speaker8 ohms, round.
External Speaker(Not Supplied)8 ohms; disables internal speaker when connected.
Anytone AT-6666Pro radio displaying power output specifications: AM 80W(PEP), FM 50W, SSB 80W(PEP).

Figure 5: Power Output Specifications

10. User Tips

  • Antenna Optimization: Always ensure your antenna is properly installed and tuned for the best possible transmission and reception. A well-matched antenna is key to maximizing the radio's performance and preventing damage.
  • Power Supply Stability: Use a stable 13.8V DC power supply that can provide sufficient current to avoid performance issues, especially during high-power transmissions.
  • Explore Menu Functions: Take time to explore the various menu functions (Channel, Public Data, Background) and programmable keys to customize the radio to your specific operating preferences.
  • Noise Reduction: Utilize the NB/ANL and NRC features to minimize interference and improve signal clarity, particularly in noisy environments.

11. Warranty & Support

For warranty information, technical support, or service inquiries, please contact your authorized Anytone dealer or visit the official Anytone website. Keep your purchase receipt as proof of purchase.

Official website: www.anytone.net

A PDF version of this user manual is available for download: Anytone AT-6666Pro User Manual (PDF)

12. Product Overview Video

Watch this video for a visual overview of the Anytone AT-6666Pro radio and its features.

Video: Anytone AT-6666Pro Product Showcase

13. Radio in Use

An example of the Anytone AT-6666Pro in an operational setting.

Anytone AT-6666Pro radio in an operational setup, showing the display and connected accessories.

Figure 6: AT-6666Pro in an operational setup

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.