1. Introduction
Thank you for choosing the YJCAL DF-M33 Mini Electrical Cable Terminal Block. This quick wire connector is designed for efficient and secure electrical connections in various applications. Please read this manual carefully before installation and use to ensure safe and optimal performance.

Figure 1: YJCAL DF-M33 Mini Electrical Cable Terminal Block
2. Safety Instructions
WARNING: Failure to follow these safety instructions may result in electric shock, fire, or serious injury.
- Always ensure the power supply is completely disconnected before wiring. Do not operate while live to prevent the risk of electric shock.
- This product is only applicable to circuits within the rated voltage (300V) and current range (15A). Refer to the product specifications for specific parameters. Overloading may cause fires or equipment damage.
- Avoid installing this product in damp, dusty, or flammable/explosive environments. It is only suitable for indoor use in dry, non-corrosive gas conditions.
- The stripping length of the wire must strictly match the terminal requirements (10-12mm). Being too long or too short may result in poor contact or arcing.
- Do not disassemble or modify this product. Non-professional operation may damage the insulation performance and cause safety hazards.
- Keep out of reach of children.
3. Package Contents
Please check the package for the following items:
- YJCAL DF-M33 Mini Electrical Cable Terminal Block(s)
Note: Quantity may vary based on purchase option.
4. Setup and Installation
4.1 Wire Preparation
- Ensure the power supply to the circuit is completely off.
- Strip the insulation from the end of the wire. The recommended stripping length is 10-12mm.
- Ensure the wire conductor is clean and free from damage.
4.2 Connection Steps
- Identify the input and output ports on the terminal block. The DF-M33 is a 3-in 3-out connector.
- For an unplugged state, the colored handles (levers) will protrude from the black plane of the connector.
- To prepare for wire insertion, push the colored handle (lever) downwards until it is flush with the black circular surface of the connector. This opens the clamping mechanism.
- Insert the stripped wire end fully into the corresponding hole.
- Finally, push the handle (lever) back up to its original protruding state. This secures the wire in place.
- Gently pull on the wire to ensure it is securely fastened and cannot be easily dislodged.
- Repeat for all wires requiring connection.
Video 1: Wire Connection Demonstration for DF-M33 Terminal Block

Figure 2: DF-M33 Connector with a Wire Securely Connected
5. Operating Instructions
The YJCAL DF-M33 terminal block is a passive component. Once wires are correctly installed, it provides a secure and reliable electrical connection. No further operation is required during normal use.
6. Maintenance
- Periodically inspect connections for any signs of loosening or damage.
- Ensure the operating environment remains dry and free from excessive dust or corrosive gases.
- Clean the exterior of the connector with a dry, soft cloth if necessary. Do not use liquid cleaners.
7. Troubleshooting
7.1 Loose Connection
If a wire feels loose or pulls out easily:
- Ensure the wire was stripped to the correct length (10-12mm).
- Verify that the handle (lever) was fully pushed up to secure the wire.
- Check if the wire gauge is within the specified connection range (0.2-1.5mm²).
7.2 No Electrical Continuity
If the circuit does not function after connection:
- Double-check that all wires are fully inserted and securely clamped.
- Ensure the power supply is active and all other components in the circuit are functioning correctly.
- Verify that the terminal block is not overloaded beyond its rated voltage (300V) and current (15A).
8. Specifications

Figure 3: DF-M33 Specifications and Dimensions

Figure 4: DF-M33 Technical Drawing with Detailed Dimensions
| Feature | Specification |
|---|---|
| Model Number | DF-M33 |
| Brand Name | YJCAL |
| Type | Crimp Terminal |
| Rated Voltage | 300V |
| Rated Current | 15A |
| Connection Range | 0.2-1.5mm² (Hard wire/Flexible cord) |
| Stripping Length | 10-12mm |
| Connection Method | 3 Input, 3 Output |
| Plastic Material | Flame retardant nylon (PA66) |
| Contact Material | Brass |
| Spring Material | Stainless Steel |
| Dimensions (Approx.) | Length: 31.6mm, Diameter: 15mm |
| Certification | CE |
| EU LVD Voltage | High voltage: Above 50Vac or 75Vdc |
| Origin | Mainland China |
8.1 CE Compliance
This product meets the CE marking requirements of the EU market and complies with the EU Low Voltage Directive (2014/35/EU) and Electromagnetic Compatibility Directive (2014/30/EU).
References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:
- EN 60998-1:2004
- EN IEC 61000-3-2:2019+A1:2021
- EN 61000-3-3:2013+A1:2019+A2:2021
- EN IEC 61000-6-1:2019
- EN IEC 61000-6-3:2021
9. User Tips
- Users appreciate the good quality and material of these terminal blocks, making them a reliable choice for electrical connections.
- Ensure wires are stripped precisely to the recommended length for the most secure and reliable connection.
10. Frequently Asked Questions (FAQ)
Q: What wire types are compatible with this connector?
A: This connector is compatible with both hard wire and flexible cord with a cross-section range of 0.2-1.5mm².
Q: Can this connector be reused?
A: Yes, the push-pull mechanism allows for wires to be inserted and removed, making the connector reusable.
Q: Is this connector suitable for outdoor use?
A: No, this connector is designed for indoor use only, in dry, non-corrosive gas conditions.
11. Warranty and Support
For warranty information and technical support, please refer to your purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.