1. Product Overview
The Yovanxer TJ7500 Electric Screen Controller is designed for intelligent control of motorized projection screens, curtains, shades, and electric remote control doors. It features advanced technology, robust safety features, and convenient long-distance operation.
2. Features
- Advanced Technology: Incorporates imported chips, advanced technology, and a reasonable design for reliable performance.
- Safety & Reliability: Features overpressure protection and lightning protection design, ensuring safe and reliable operation.
- Long-Distance RF Control: Designed for long-distance radiofrequency emission, allowing simple and convenient operation without obstruction.
- Intelligent Learning: The remote receiver is an intelligent learning type, enabling easy setup with multiple remote control handles.
- Automatic Linkage: Can be configured to automatically open the screen when the projector is turned off and close it when the projector is turned on.
3. Scope of Application
This product is designed for controlling AC motors (AC85-265V, other specifications customizable) for positive, stop, and reverse operations. Typical applications include:
- Electric Projection Screens
- Motorized Curtains
- Electric Shades
- Electric Remote Control Doors
4. Technical Specifications
| Parameter | Specification |
|---|---|
| Rated Voltage | AC85-265V |
| Load Power | ≤ 500W |
| Operating Frequency | 315 MHz (433 MHz optional) |
| Control Current | 3A |
| Remote Control Distance | ≥ 50 meters (open space) |
| Transmitter Batteries | 23A / 12V |
| Channel | 1 |
| Wireless Communication | RF |
| Use | Projectors |
5. Installation
Important: Installation should only be performed by a professional. Ensure power is OFF before wiring to prevent electric shock.
- Power Off: Before installation, verify the voltage and ensure the power supply is completely disconnected.
- Wiring: Connect the wiring according to the diagram provided on the receiver panel. Ensure all connections are secure and insulated to prevent short circuits.
- Secure Installation: Mount the receiver in a suitable location, avoiding hot and humid environments.
6. Operation
6.1. Learning and Clearing Remote Control Codes
| Function | Condition | Procedure |
|---|---|---|
| Learn | When the controller needs to pair a new remote control. | In standby state (red light ON, motor OFF), long press the middle 'Stop' button on the controller for 3 seconds. Once the red light turns OFF, immediately press any button on the remote control. The red light will flash and then stay ON, indicating successful learning. The remote control is now ready for use. |
| Clear Code | To clear all remote code values from the controller. | In standby state (red light ON, motor OFF), long press the middle 'Stop' button on the controller. After the red light turns OFF (approx. 5 seconds), it will flash and then stay ON. All previously learned remote controls will no longer work. Note: After clearing, the controller will re-enter learning mode. If no remote is learned within 5-10 seconds, it will exit learning mode automatically. |
6.2. Automatic Projector Linkage
The TJ7500 controller can be linked with your projector using the USB trigger to automate screen operation.
- Insert Trigger: Insert the USB trigger into an available USB port on your projector.
- Pairing (if not already done): Follow the 'Learn' procedure above to pair your remote control with the main controller.
- Automatic Operation:
- When the projector is turned OFF, the screen will automatically open.
- When the projector is turned ON, the screen will automatically close.
7. Precautions
- Do not install the receiver in hot or humid places to ensure optimal performance and longevity.
- If the motor does not operate after installation, re-verify that the center line is connected correctly. If the issue persists, consult your supplier.
- If the motor runs in the incorrect direction (e.g., screen goes down instead of up), exchange the ascending and descending wires.
- If the remote control range is shortened or it fails to respond, replace the remote control battery (23A / 12V).
- Ensure all wiring connections are properly insulated to prevent short circuits.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not working after installation | Incorrect center line connection. | Verify the center line connection. If problem persists, contact supplier. |
| Motor runs in wrong direction | Ascending and descending wires are swapped. | Exchange the ascending and descending wires. |
| Remote control range is short or unresponsive | Low battery in remote control. | Replace the remote control battery (23A / 12V). |
| Remote control not working | Remote not paired or codes cleared. | Perform the 'Learn' procedure to pair the remote control. |
9. User Tips
- Battery Availability: The 23A / 12V batteries for the remote control can be easily found on online shopping websites.
- Easy Programming: Many users find the remote control programming (learning and clearing codes) to be very simple and intuitive.
- Automated Convenience: The automatic on/off feature linked with your projector is highly praised for its convenience, enhancing your home theater experience.
- Check Wiring First: If you encounter issues with the motor not responding, always double-check your wiring connections as per the diagram.
10. Warranty
The product comes with a three-year warranty. During this period, the product will be repaired or replaced free of charge if damage occurs due to non-human factors or improper installation. This warranty does not cover damage caused by misuse or unauthorized modifications.
For further assistance, you may refer to the official user manual PDF: View User Manual (PDF)