Important Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, please read the following instructions carefully.
- Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
- Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
- Make sure all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
- Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.
- If you are mounting the fan on a ceiling outlet box, use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 lbs.). Do not use a plastic outlet box. Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.
- If you are mounting the fan to a joist, make sure it is strong enough to support the moving weight of the fan (at least 50 lbs.).
- After installing the fan, make sure all the connections are secured. This will prevent the fan from falling.
- Do not insert anything into the fan blades while the fan is operating.
- Turn the fan off and wait for it to stop before reversing fan direction.
- To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.
- To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state.
- To reduce risk of personal injury, use only the two steel screws and lock washers provided with the fan for mounting the outlet box.
Product Overview
This Nordic LED Ceiling Fan is designed for optimal air circulation and lighting in various indoor settings such as restaurants, living rooms, and homes. It features a DC silent motor, remote control operation, and a modern industrial retro style. Available in 42-inch and 52-inch sizes, with options for 60-inch diameter for stronger wind force.
Setup and Installation
Unpacking Your Fan
Unpack your fan and check the contents. Please check each item prior to installation. To reduce the chance of marks or possible damages, please remove the parts when required for installation.
Parts List (With Light)
| Ref.# | Description | Part# |
|---|---|---|
| 1 | Hanger Bracket | 1 |
| 2 | Canopy | 1 |
| 3 | Downrod Assembly | 1 |
| 4 | Coupling Cover | 1 |
| 5 | Fan Motor Assembly | 1 |
| 6 | Blade | 3 |
| 7 | Light Kit | 1 |
| 8 | Shade | 1 |
| 9 | Remote Control | 1 |
Installation Steps (With Light)
WARNING: The fan must be hung with at least 230 cm (7 feet) of clearance from floor to blades.
- Securely attach the hanger bracket to the ceiling joist using the lag bolt, flat washer, and spring washer supplied.
- Install the fan blades by aligning the holes on the blade with the holes on the fan motor assembly set by the provided set screws and washers. Make sure the set screws securing the blade are tight and the blades are properly seated.
- Connect the canopy, downrod, coupling cover, and fan motor assembly as previously stated in general assembly instructions.
- Lift the fan as previously stated in general assembly instructions.
- Connect the wires from the motor assembly and wires from the LED correctly. Attach the light kit plate to the fan motor assembly using the two light kit plate screws.
- Install the shade into the light plate. Make sure it is secure but not overly tight.
Wiring Connections
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
Connect 220-240V main power (dwelling) to the Terminal Block located on the hanger bracket. Plug the receiver in the hanger bracket with the flat side facing up.
- Insert the 3P connector of hanger bracket into the AC POWER INPUT socket of receiver.
- Insert the 2P light connector of fan motor assembly into the 2P LIGHT socket of receiver.
- Insert the 3P motor connector of fan motor assembly into the 3P MOTOR socket of receiver.
- Connect the 1P yellow/green connectors of fan motor assembly and hanger bracket.
Mount the canopy by tightening the two screws.
Install the rubber plug into the motor axis.
Operating Instructions
Remote Control Functions
The fan is operated using a 2.4G remote control, offering a stronger signal and wider range. The remote control and receiver are paired using a learning code.
The remote control features:
- ALL OFF: Turns off all fan and light functions.
- LIGHT ON/OFF: Toggles the LED light on or off.
- FAN ON/OFF: Toggles the fan on or off.
- Fan Speed Control (1-6): Adjusts fan speed from 1 (low) to 6 (high).
- Fan Positive and Negative Rotation Control: Changes the direction of fan blade rotation for summer (downward airflow) or winter (upward airflow).
- Fan Timing Control: Sets a timer for fan operation.
Pairing Remote and Receiver
IMPORTANT: Pairing initial step must be performed within 30 seconds of power being turned on.
- Turn ON the power supply. Within 30 seconds, press and hold the remote control's 'ALL OFF' button for 5 seconds. A 'beep' will be heard, indicating successful pairing. All functions should now work normally.
- When pairing multiple fans, ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing further fans (i.e., pair one fan at a time).
- Ensure the isolation switch is kept to the ON position. The isolation switch is not to be used as a light switch as this will damage and make the remote receiver inoperable.
Protective Functions of the Receiver
- Lock Protection: The DC motor has a built-in safety feature against blade or motor obstruction during operation. If something obstructs the fan blades or motor, the motor will keep trying to run and then stop operation after about 30 seconds of interruption. To reset, remove obstacles and reset by turning the fan off via remote and then turning it back on.
- Overload Protection (Current Limit): The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.
Maintenance
- Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
- When cleaning, use only a soft brush or lint-free cloth to avoid scratching the finish.
- Abrasive cleaning agents are not required and should be avoided to prevent damage to finish.
WARNING: Do not use solvents when cleaning your ceiling fan. It could damage the motor and create the possibility of electrical shock.
Periodically check that the blade sets to the fan motor set screws are secure and tight.
Before carrying out any cleaning or maintenance work, always make sure that the appliance is disconnected.
LED lights are not removable. LED lights can only be used within the product delivery; they cannot be replaced.
Troubleshooting
Balancing Fan / Wobbling Trouble Shooting
Please note that all ceiling fans are not the same; even in the same model, some may move more or less than others. Movement of a couple of centimeters is quite acceptable and does not suggest the fan will fall down. Even though all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether. This should not be considered a fault. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted.
Try the following to reduce a wobbling fan:
- Check that all of the blade mounting screws are tightened and secure.
- Wobbling problems may result from inconsistent blade level. To check the blade level, measure the distance from each blade tip to the ceiling. If measurements are inconsistent:
- Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevel blade tip.
- An out of shape blade can cause wobbling. Check by removing the blade and placing it on a flat surface.
- Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades. If a blade is not in alignment, the blade is either out of shape, warped, or the blade screws are not evenly tightened or either loose.
A Balancing Kit has been provided to assist with reducing a wobble. Please retain the kit as it may become useful should the fan develop a wobble in the future. Instructions on how to use the Balancing kit can be found within the Kit.
Remote Control Issues
- If the remote control cannot control the receiver, check whether the battery is loaded correctly.
- Too low battery voltage will affect the remote control distance and may cause remote control failure. Replace the battery in time.
- If the fan or light is not working, reset power (turn the power off for at least 5 seconds and then turn the power back on) and redo the learn function setting.
- If the transmitter functions are not working, check the battery orientation and power level. Low battery voltage will affect the functions of your transmitter and operation of your fan.
- Other remote controls nearby using the same frequency may cause interference with the fan's receiver.
Specifications
| Attribute | Value |
|---|---|
| Model Number | XG-Ceiling fan lights |
| Brand Name | ludengchaoshi |
| Item Type | Ceiling Fans |
| Power Source | AC |
| Control Method | REMOTE CONTROL |
| Switch Type | REMOTE CONTROL |
| Body Material | ABS, IRON |
| Luminous Flux | 2000-82000 |
| Is Dimmable | No |
| Is Bulbs Included | No (LED is integrated) |
| Is Batteries Included | No |
| Certification | CE, ROHS |
| Origin | Mainland China |
| Warranty | 1 year |
| Installation Method | Assembly |
| Package Length | 77 cm |
| Package Width | 33 cm |
| Package Height | 19 cm |
| Package Weight | 6.487 kg |
Warranty and Support
This product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For detailed instructions and diagrams, you may refer to the official user manual PDF: View User Manual (PDF).
User Tips
- For optimal performance, ensure the fan blades are clean and free from dust buildup.
- When changing fan direction for seasonal use, always turn off the fan and allow it to come to a complete stop before reversing the rotation.
- If the remote control signal seems weak, try replacing the batteries.
- Consider the fan's size (42/52/60 inch) in relation to your room dimensions for effective air circulation.
Frequently Asked Questions (FAQ)
- Q: Is the LED light dimmable?
- A: No, according to the specifications, the LED light is not dimmable. It can be turned on and off via the remote control.
- Q: What should I do if the fan wobbles?
- A: Refer to the 'Balancing Fan / Wobbling Trouble Shooting' section in this manual. Ensure all blade mounting screws are tight and check for consistent blade level. A balancing kit is provided for further adjustment.
- Q: How do I pair the remote control with the fan?
- A: Turn on the power supply to the fan. Within 30 seconds, press and hold the 'ALL OFF' button on the remote control for 5 seconds until you hear a 'beep'. This indicates successful pairing.
- Q: Can I install this fan on a sloped ceiling?
- A: No, the safety instructions explicitly state not to install this fan on a sloped ceiling to reduce the risk of electrical shock and personal injury.