1. Introduction
This manual provides detailed instructions for the installation, configuration, and operation of your Diatone MAMBA F722 APP MK4 Flight Controller (FC) Stack. This high-performance stack is designed for FPV drones, offering advanced features and robust performance for both freestyle and racing applications. Please read this manual thoroughly before proceeding with installation and setup.
2. Safety Warnings
- Static Electricity: During operation, especially when handling the boards, always wear anti-static equipment. Ensure all soldering equipment is properly grounded to prevent damage from static discharge.
- Propeller Removal: For your safety, always remove propellers from your drone before connecting the flight controller to a computer for Betaflight setup or any configuration changes.
- Voltage Check: Always verify the voltage of your power source and components before making any electrical connections to prevent damage.
- Soldering: Exercise caution when soldering. Ensure proper ventilation and use appropriate safety gear.
3. Package Contents
The package typically includes the following items:
- MAMBA F722 APP MK4 Flight Controller
- MAMBA 4-in-1 ESC (45A, 55A, or 65A depending on variant)
- Connection Cables
- Mounting Hardware (Screws, nuts)
- Diatone Stickers
- User Manual (PDF version available online)
4. Specifications
4.1. Flight Controller (MAMBA F722 APP MK4)
| Feature | Specification |
|---|---|
| MCU | STM32F722 |
| GYRO | ICM42688P |
| OSD | Yes |
| Blackbox | 16M |
| BEC | 3.3V 0.5A / 5V 3A / 9V 3A |
| Mounting | 30.5x30.5mm |
| Size | 44.5x40x7.5mm |
| Weight | 10g |
| WIFI | SpeedyBee APP compatible |
| Air Unit Port | Yes (Supports O3 fast connection) |
| Protection | BEC Protection, Receiver Protection, TVS Protection |
| Software | Betaflight |
4.2. ESC (MAMBA F45/F55/F65_128K 4-in-1)
| Feature | Specification |
|---|---|
| Input Voltage | 4-6S Lipo (14.8-25.2V) |
| Output Current | 45A / 55A / 65A (per variant) |
| Peak Current | 55A / 65A / 75A (per variant) |
| BLHeli Suite | BLHeliSuite32 |
| PWM | 24-128K |
| Protocol | Dshot 300/600/1200 |
| Mounting | 30.5x30.5mm |
| Size | 44.5x40x7.5mm |
| Weight | 15g |
| Material | Metal |
5. Setup and Wiring
Before wiring, always ensure you have read the safety warnings. Refer to the comprehensive wiring diagram below for all connections.
5.1. General Wiring Principles
- Check Voltage: Always check the voltage before wiring. The default VTX voltage is 9V.
- UART Configuration: Ensure correct UART settings in Betaflight for peripherals.
- SBUS/F.Port: SBUS and F.Port cannot be connected simultaneously.
5.2. DJI Air Unit Wiring
The MAMBA MK4 F722 APP supports DJI O3 Air Unit fast connection.
- Connect the DJI Air Unit to the designated port on the FC.
- If you are not using a DJI FPV remote control, disconnect the SBUS (RX1) connection.
- The VTX power switch channel is USER1. By default, it's connected. You can control power on/off after setting the channel.
- Correspond USER1 to an AUX channel on your remote control.
5.3. Receiver Wiring (MSR, TBS Crossfire, DSM)
For MSR (F.Prot), MSR (SBUS), and TBS Crossfire Nano receivers, configure a Serial Port (via the Ports tab in Betaflight) and choose the appropriate Serial Receiver Provider.
- MSR Receiver (F.Prot): Connect to the designated RX pad.
- MSR Receiver (SBUS): Connect to the designated RX pad.
- TBS Crossfire Nano: Connect CRSF to the appropriate UART TX/RX pads.
- DSM Receivers: Follow these steps for DSM receivers:
- Select DSMX protocol (SPEKTRUM2048 or SPEKTRUM2040) in Betaflight.
- In the Betaflight CLI, enter:
set spektrum_sat_bind = 5 save - Perform the frequency pairing operation on your receiver.
- After successful pairing, in the Betaflight CLI, enter:
set spektrum_sat_bind = 0 save
5.4. Video Transmitter (VTX) Wiring
For MAMBA ULTRA 1000 VTX or TBS UNIFY PRO32 NANO 5G8 32 bit VTX:
- Connect VTX to the designated VTX pad and GND.
- Ensure the VTX power switch channel (USER1) is configured if you wish to control VTX power via your remote.
- For MAMBA ULTRA 1000, use 9V for 6S voltage or VCC for 3-4S voltage.
- In Betaflight, enable VTX (IRC Tramp) on the appropriate UART (e.g., UART3).
5.5. GPS Module Wiring
For MAMBA M22/M8 PLUS GPS modules:
- Connect GPS RX to FC TX, and GPS TX to FC RX. Connect 5V and GND.
- In Betaflight, configure a Serial Port (via the Ports tab) for GPS feature (e.g., UART2).
- Set GPS protocol (e.g., NMEA) and other parameters as needed.
5.6. Buzzer Wiring
Connect the buzzer to the BUZ+ and BUZ- pads on the flight controller.
5.7. LED Wiring
Connect LED strips to the LED-IN pad and 5V/GND. The LEDs can be controlled by Betaflight when the upper pads are shorted, or by the Mamba LED Control System (On Board) when the lower pads are shorted.
- Click once to change color.
- Double click for flash mode.
- Press and hold to turn on/off.
5.8. Camera Wiring
Connect your FPV camera to the CAM pad for video input, and 5V/GND for power.
5.9. SpeedyBee APP Setup (Mobile WIFI Reference)
The SpeedyBee APP allows for convenient wireless configuration of your flight controller.
- Download the App: Download the SpeedyBee APP from www.speedybee.com/download/.
- Enable UART4 MSP: Ensure that the UART4 MSP setting is enabled (default on) in Betaflight.
- Connect to WIFI: Open the SpeedyBee APP and connect your mobile device to the FC's WIFI network. The WIFI name is typically "Mamba Stack". If your specific model is not listed, select any Diatone model.
6. Operating Instructions
Once the flight controller stack is correctly wired and configured in Betaflight, you can proceed with operating your FPV drone. Ensure all pre-flight checks are performed, including propeller security, battery connection, and radio link.
- Arming: Arm your drone using the configured switch on your remote control.
- Flight Modes: Select desired flight modes (e.g., Acro, Angle, Horizon) via your remote.
- OSD: Utilize the On-Screen Display (OSD) for real-time flight data, battery voltage, and other critical information.
- Logging: The 16M Blackbox allows for flight data logging, useful for tuning and troubleshooting.
7. Maintenance
- Regular Inspection: Periodically inspect all solder joints and connections for any signs of wear, corrosion, or damage.
- Cleaning: Keep the boards clean from dust, dirt, and debris. Use compressed air or a soft brush. Avoid using liquids directly on the electronics.
- Firmware Updates: Regularly check for new Betaflight firmware versions. When updating, always back up your configuration and follow the update instructions carefully.
- Storage: Store the stack in a dry, anti-static environment when not in use.
8. Troubleshooting
- No Power/Intermittent Power:
- Check all power connections, including battery leads and main power pads.
- Verify battery voltage and ensure it's within the 4-6S Lipo range.
- Inspect for any short circuits or damaged components.
- SpeedyBee APP "Connecting" or "MSP not responding":
- Ensure UART4 MSP is enabled in Betaflight.
- Update the SpeedyBee APP to the latest version.
- Restart both your device and the SpeedyBee APP.
- Reboot the flight controller.
- Unstable Flight/Performance Issues:
- Ensure propellers are balanced and undamaged.
- Check motor connections and ESC calibration.
- Review Betaflight PID tuning and filter settings.
- Avoid self-flashing firmware if you are unsure, as it may lead to unstable operation.
- Receiver Not Connecting:
- Verify receiver wiring to the correct UART TX/RX pads.
- Ensure the correct Serial Receiver Provider is selected in Betaflight (e.g., SBUS, CRSF, SPEKTRUM).
- Confirm the receiver is properly bound to your radio transmitter.
9. User Tips
- The large soldering pads on this stack make wiring easier, especially for beginners.
- This stack is known for its solid build and reliability, handling 6S power well and staying cool during aggressive flying. It performs excellently for both freestyle and racing.
- The 30x30mm mounting pattern is standard and suitable for most 5-inch drone frames.
- While the WiFi feature is convenient, some users have noted occasional 'chatter' or interference. If experiencing issues, ensure your WiFi connection is stable or try a wired connection for critical configurations.
10. Frequently Asked Questions (FAQ)
- Q: Is this a complete stack or just a Flight Controller?
- A: This is a complete stack, including both the Flight Controller (FC) and a 4-in-1 Electronic Speed Controller (ESC).
- Q: What is the mounting pattern for this stack?
- A: The stack uses a 30x30mm mounting pattern, which is suitable for standard 5-inch drone builds.
- Q: Is it compatible with DJI Air Units?
- A: Yes, the MAMBA MK4 F722 APP is designed to support DJI Air Units, including the O3 Air Unit, with dedicated wiring options.
- Q: What is the difference between A and B versions of gyros?
- A: Information regarding specific differences between 'A' and 'B' versions of gyros is not provided in this manual. Please refer to the product's official documentation or contact Diatone support for details.
11. Warranty and Support
Diatone products are certified brands and committed genuine items. For detailed warranty information, technical support, or further documentation, please refer to the official Diatone website or the comprehensive user manual PDF available at https://manuals.plus/m/f125ab18b8870288c98c1698a65dee893cf7d11dbf9feb3922713d45ef7df40a.
For any issues not covered in this manual, please contact your retailer or Diatone customer service.