LAUNCH CRP919X

Contents

LAUNCH X431 CRP919X OBD2 Scanner User Manual

Model: CRP919X

Brand: LAUNCH

1. Introduction

1.1 Trademarks

LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. in China and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Copyright © 2022 by LAUNCH TECH CO., LTD. (also called LAUNCH for short). All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission.

1.3 Disclaimer of Warranties and Limitation of Liabilities

  • All information, illustrations, and specifications in this manual are based on the latest information available at the time of publication.
  • The right is reserved to make changes at any time without notice. We shall not be liable for any direct, special, incidental, indirect damages or any economic consequential damages (including the loss of profits) due to the use of the document.
  • To take full advantage of the unit, you should be familiar with the engine.
  • LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH.

1.4 Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the tool, please read this user's manual first carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

  • There are no user serviceable parts. Have the device serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the device is maintained. Disassembling the device will void the warranty right.
  • Caution: This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce or dispose of the battery in fire or water.
  • This product is not a toy. Do not allow children to play with or near this item.
  • Do not expose the device to rain or wet conditions.
  • Do not place the device on any unstable surface.
  • Never leave the device unattended during charging process. The device must be placed on a non-flammable surface during charging.
  • Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
  • Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
  • Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the device when necessary.
  • People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.

1.5 FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

2. Product Overview

The LAUNCH X431 CRP919X is a professional automotive scanner designed for comprehensive vehicle diagnostics, offering advanced features like ECU Coding and Bi-Directional Control.

LAUNCH X431 CRP919X OBD2 Scanner with its carrying case and accessories.
Figure 1: LAUNCH X431 CRP919X OBD2 Scanner and accessories.
Key selling points of the LAUNCH CRP919X: All System Diagnosis, 31+ Reset Service, Active Test, ECU Coding, CANFD & DOIP support, 2-Year Free Update, 5-Year Warranty, Lifetime Tech Support, 10 Languages, 100+ Car Brands.
Figure 2: Key features and benefits of the CRP919X scanner.

2.1 Components & Controls

Diagram showing the components and controls of the LAUNCH CRP919X scanner, including charging port, diagnostic connector, power button, display screen, charging LED, navigation buttons, OK button, HOME button, adjustable stand, camera flash, and rear camera.
Figure 3: Front and rear view of the CRP919X scanner with labeled components.
  1. Charging Port: Connects the tool to PC to charge it.
  2. DB15 Diagnostic Connector: Connects the tool to the vehicle's Data Link Connector (DLC).
  3. Power Button: Turns on/off the tool.
  4. Display Screen: 7-inch IPS touch screen, indicates test results.
  5. Charging LED: Red means Charging; Green means Fully Charged.
  6. Back Button: Returns to previous menu.
  7. Select Buttons (Up/Down/Left/Right): Used for navigation in menus and data views.
  8. OK Button: Confirms a selection (or action) from a MENU list.
  9. HOME Button: Navigate to the Job Menu screen.
  10. Adjustable Stand: Flips out to any angle for comfortable use or hanging on a steering wheel.
  11. Camera Flash
  12. Rear Camera

2.2 Accessories Checklist

The following accessory items are for reference purpose only. For detailed accessory items, please consult from the local agency.

  1. Diagnostic tool x 1
  2. OBD II diagnostic cable x 1
  3. DC 5V charging cable x 1
  4. Power adaptor x 2
  5. Multilingual quick start guide x 1
  6. User manual x 1

3. Setup and Initial Use

3.1 Charging & Turning On/Off

3.1.1 Charging

There are two charging methods available:

  • Via Charging Cable & Power Adaptor: Plug one end of the included charging cable into the DC-IN port of the tool, and the other end to the external DC power.
  • Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's DLC.

Once the charging LED illuminates solid green, it indicates that the battery is fully charged.

Note: Attempting to charge the tool via OBD diagnostic port will consume vehicle's battery power. You are not recommended to charge the tool in this way except for OBD diagnosis operations.

3.1.2 Turning On/Off

  • Press the Power button for about 3 seconds to turn it on.
  • Press the Power button for about 8 seconds to turn it off.

3.2 Getting Started

If it is the first time you have used this tool, you need to make some system settings.

  1. Power on the tool. The screen displays a welcome page. Tap Welcome to use to go to next step.
  2. Choose the desired system language, and tap Next step.
  3. Choose the desired time zone, and tap Next step to enter the WLAN setup screen.
  4. Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network.
  5. If the network you chose is open, you can connect directly. If the selected network is encrypted, you have to enter the right security key (network password).

Note: If you choose Ignore in WLAN setup, it will go into the date setting page. If the tool has been properly connected to the Internet, the system will automatically obtain the correct network date and time and navigate to step 5.

  1. After the network connection is done, tap Next Step to configure workshop information. Input the required information, and tap Next Step to go to next step.

Note: After you configured it, the system will append it on the report every time a report is successfully generated.

  1. Carefully read all terms and conditions of the user agreement, check the box before the Agree to all the above terms, and tap OK to finish the sign-up process and navigate to Job Menu.

3.3 Settings

The main menu screen includes the following function modules:

  • Diagnose: Configure it to operate as a professional diagnostic tool.
  • OBD II: This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.
  • Reset: Perform commonly used repair & maintenance services.
  • Battery Voltage: Measure the current voltage of the vehicle's battery.
  • Data: Includes Diagnostic report, Diagnostic record, Feedback and DTC library etc.
  • Mall: To subscribe extra vehicle diagnostic software or reset software that are not included within the tool.
  • Upgrade: Update vehicle diagnostic software and APK. This function requires a stable network connection.
  • Add-on Modules: There are two add-on modules available for extending the functions of the tool. Each module consists of two parts: hardware and app. These modules cannot work properly on the tool, which need to work with the specific compatible hardware (sold separately).
  • Settings: Make some system settings, including Network setup, Email and Brightness etc.

3.3.1 Units of measurement

It is designed to set the measurement unit. Metric System and English System are available.

3.3.2 Automatic detection on connect

This option enables you to determine whether to start an automatic VIN detection once the tool is properly connected to the vehicle's DLC.

3.3.3 Firmware Fix

This option enables you to fix and repair the tire pressure firmware and the VCI firmware.

3.3.4 Display/Brightness

This item allows you to set the standby time and screen brightness.

Note: Reducing the brightness of the screen is helpful to conserve the power of the tool.

3.3.5 Sound

This option lets you adjust the volume and other sound settings.

3.3.6 Network

The tool has built-in WLAN module that can be used to get online. Once you're online, you can register your tool and update diagnostic software & APK. Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network to connect.

Note: Once WLAN is set as ON, the tool will consume more power. While it keeps unused, please set it off to save power. While WLAN keeps unused, please turn it off to conserve battery power.

3.3.7 Date/Time

This option allows you to set the system time and time zone.

3.3.8 Language

The tool supports multiple languages. You can use this option to change the system language to the target language.

3.3.9 Workshop information

This option allows you to configure the workshop information.

Note: After you configured it, the system will append it on the report every time a report is successfully generated.

3.3.10 Recovery

Use this item to reset this tool to the default factory setting.

Warning: Resetting may cause data loss. Before doing so, please be careful to perform this operation.

3.3.11 Clean Up

This option allows user to clear some cache files and free up some storage space. After clean up, the tool will reboot automatically.

3.3.12 About

This option displays the hardware configuration information of the tool and license agreement.

4. Operation

4.1 Vehicle Coverage

This diagnostic tool is specially designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). It is required by EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant and this includes all American, Asian and European vehicles.

A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the following:

  1. Vehicle Emissions Control Information (VECI) Label: It is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate OBD II Certified.
  2. Government regulations mandate that all OBD II compliant vehicles must have a "common" 16-pin Data Link Connector (DLC).

Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only those vehicles with a Vehicle Emissions Control Label stating OBD II Certified are OBD II compliant.

Image showing various car brands covered by the LAUNCH CRP919X, including European, Asian, and American manufacturers, supporting 20000+ vehicles and multiple languages.
Figure 4: Extensive vehicle coverage for the CRP919X scanner.

4.2 OBD II Definitions

The following terms and their definitions are related to OBD II systems. Read and reference this list as needed to aid in the understanding of OBD II systems.

  • EOBD: European On-Board Diagnostics. Essentially the same as OBD II, with the same Data Link Connector and Communication Protocols.
  • Communication Protocols: Allows different systems and sensors in a vehicle to communicate. There are currently five protocols: CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
  • Powertrain Control Module (PCM): The PCM is the OBD II accepted term for the vehicle's “on-board computer." In addition to controlling the engine management and emissions systems, the PCM also participates in controlling the powertrain (transmission) operation. Most PCMs also have the ability to communicate with other computers on the vehicle (ABS, ride control, body, etc.).
  • DLC: Data Link Connector. The 16-cavity connector on the vehicle that allows communication between the computer system and the diagnostic tool.
  • MIL: Malfunction Indicator Lamp. The vehicle's “Check Engine” warning light that activates when a DTC is stored.
  • DTC: Diagnostic Trouble Code. A code stored in the computer system's memory, which helps to identify the fault condition that is causing the MIL to activate.
  • Freeze Frame Data: Operating conditions that are stored when a DTC is stored.
  • PID: Parameter Identification Data. Data returned by the vehicle's control modules to the diagnostic tool.
  • Monitors: Monitors are “diagnostic routines” programmed into the PCM. The PCM utilizes these programs to run diagnostic tests, and to monitor operation of the vehicle's emissions-related components or systems to ensure they are operating correctly and within the vehicle's manufacturer specifications. Currently, up to fifteen Monitors are used in OBD II systems. Additional Monitors will be added as the OBD II system is further developed.
  • Enabling Criteria: Also termed Enabling Conditions. They are the vehicle-specific events or conditions that must occur within the engine before the various monitors will set, or run.
  • Trip: A Trip for a particular Monitor requires that the vehicle is being driven in such a way that all the required “Enabling Criteria” for the Monitor to run and complete its diagnostic testing are met.
  • Drive Cycle: A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the "ready" condition.
  • Warm-up Cycle: Vehicle operation after an engine off period where engine temperature rises at least 40°F (22°C) from its temperature before starting, and reaches at least 160°F (70°C).
  • Fuel Trim (FT): Feedback adjustments to the base fuel schedule.

4.3 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code.

  • The 1st character is a letter (B, C, P or U). It identifies the main system where the fault occurred (Body, Chassis, Powertrain, or Network).
  • The 2nd character is a numeric digit (0 thru 3). It identifies the type of code (Generic or Manufacturer-Specific).

Note: Generic DTCs are codes that are used by all vehicle manufacturers. Manufacturer-Specific DTCs are codes that are controlled by the vehicle manufacturers.

  • The 3rd character is a letter or a numeric digit (0 thru 9, A thru F). It identifies the specific system or sub-system where the problem is located.
  • The 4th and 5th characters are letters or numeric digits (0 thru 9, A thru F). They identify the section of the system that is malfunctioning.
Example of a DTC (P0201) breakdown showing how each digit identifies the system, code type, sub-system, and specific malfunction.
Figure 5: DTC Structure Example (P0201).

The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-pin connector where diagnostic code readers interface with the vehicle's on-board computer. It is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary.

Diagram showing common locations of the Data Link Connector (DLC) in various car models, including Opel, Volkswagen, Audi, Honda, Changan, Hyundai, Daewoo, Kia, Toyota, Nissan, Mitsubishi, Renault, BMW, Mercedes-Benz, Mazda, GM, Chrysler, Peugeot, Regal, Beijing Jeep, and Citroen.
Figure 6: Common DLC Locations.

If the DLC cannot be found, refer to the vehicle's service manual for the location.

4.5 OBD II Monitors

An important part of a vehicle's OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits.

Monitor operation is either “Continuous” or “Non-Continuous,” depending on the specific monitor.

4.5.1 Continuous Monitors

Some of the vehicle components or systems are continuously tested by the vehicle's OBD II system, while others are tested only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:

  1. Misfire Monitor: This Monitor continuously checks for engine misfires. There are three types of engine misfires, Types 1, 2, and 3.
  2. Fuel System Monitor: This Monitor uses a Fuel System Correction program, called Fuel Trim, inside the on-board computer.
  3. Comprehensive Components Monitor (CCM): This Monitor continuously checks all inputs and outputs from sensors, actuators, switches and other devices that provide a signal to the computer.

4.5.2 Non-Continuous Monitors

"Non-continuous" Monitors perform and complete their testing once per trip. The "non-continuous" Monitors are:

  1. O2 Sensor Monitor: The Oxygen Sensor monitors how much oxygen is in the vehicle's exhaust.
  2. O2 Sensor Heater Monitor: The Oxygen Sensor Heater Monitor tests the operation of the oxygen sensor's heater.
  3. Catalyst Monitor: The catalytic converter is a device that is installed downstream of the exhaust manifold.
  4. Heated Catalyst Monitor: Operation of the "heated" catalytic converter is similar to the catalytic converter. The main difference is that a heater is added to bring the catalytic converter to its operating temperature more quickly.
  5. EGR (Exhaust Gas Recirculation) System Monitor: The Exhaust Gas Recirculation (EGR) system helps reduce the formation of Oxides of Nitrogen during combustion.
  6. Evaporative System Monitor: OBD II vehicles are equipped with a fuel Evaporative system (EVAP) that helps prevent fuel vapors from evaporating into the air.
  7. Secondary Air System Monitor: When a cold engine is first started, it runs in open-loop mode. During open-loop operation, the engine usually runs rich.

4.6 DTCs and MIL Status

When the vehicle's on-board computer detects a failure in an emissions-related component or system, the computer's internal diagnostic program assigns a diagnostic trouble code (DTC) that points to the system (and subsystem) where the fault was found. The diagnostic program saves the code in the computer's memory. It records a “Freeze Frame” of conditions present when the fault was found, and lights the Malfunction Indicator Lamp (MIL). Some faults require detection for two trips in a row before the MIL is turned on.

Note: The "Malfunction Indicator Lamp" (MIL) is the accepted term used to describe the lamp on the dashboard that lights to warn the driver that an emissions-related fault has been found. Some manufacturers may still call this lamp a "Check Engine" or "Service Engine Soon" light.

There are two types of DTCs used for emissions-related faults: Type “A” and Type "B.” Type "A" codes are “One-Trip” codes; Type “B” DTCs are usually Two-Trip DTCs.

The MIL will stay lit for both Type “A” and Type “B” codes until one of the following conditions occurs:

  • If the conditions that caused the MIL to light are no longer present for the next three trips in a row, the computer automatically turns the MIL “Off” if no other emissions-related faults are present. However, the DTCs remain in the computer's memory as a history code for 40 warm-up cycles (80 warm-up cycles for fuel and misfire faults). The DTCs are automatically erased if the fault that caused them to be set is not detected again during that period.
  • Misfire and fuel system faults require three trips with “similar conditions” before the MIL is turned “Off.” These are trips where the engine load, RPM and temperature are similar to the conditions present when the fault was first found.

Note: After the MIL has been turned off, DTCs and Freeze Frame data stay in the computer's memory.

Erasing the DTCs from the computer's memory can also turn off the MIL. If a Diagnostic Tool is used to erase the codes, Freeze Frame data will also be erased.

4.7 Diagnose Function

This function is specially designed to diagnose electronic control systems of single vehicle model.

4.7.1 Connection

  1. Turn the ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC).
  3. Plug one end of the diagnostic cable into the vehicle's DLC (Data Link Connector) port, and the other end to the DB-15 diagnostic connector of the tool, and then tighten the captive screws.

Notes:

  • A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the diagnostic cable.
  • The cable connector is keyed and will only fit one way. If you have problems connecting the cable connector to the DLC, rotate the connector 180° and try again.
  1. Turn the ignition on. Engine can be off or running.

Caution: Don't connect or disconnect any test equipment with the ignition on or engine running.

  1. Press the [POWER] button to turn it on and enter the Job Menu.

4.7.2 Perform System Diagnostics

This function is specially designed to diagnose electronic control systems of single vehicle model.

4.7.2.1 Smart Diagnosis (Auto-Detect)

This function allows you to quickly access the electronic control systems of the vehicle via decoding the VIN, without manual step-by-step menu selection. After connection, turn the ignition key on and the system enters auto-detect mode. Make sure the Automatic detection on connect in Settings is set as ON.

Note: To detect more and accurate VINs, a stable network connection is highly recommended for this function.

Caution: Don't connect or disconnect any test equipment with ignition on or engine running.

Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, a diagnostic report will be automatically generated.

4.7.2.2 Manual Diagnosis

If the tool can not obtain the VIN information, you can also perform vehicle diagnosis manually. In this mode, you need to execute the menu-driven command and then follow the on-screen instruction to proceed.

Notes:

  • Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your tool.
  • For vehicles manufactured by different vendors, it is possible that it has different diagnostic menus. For details, please follow the instructions on the screen to proceed.

4.7.3 Perform OBD II Diagnosis

This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.

After the tool is properly connected to the vehicle's DLC, tap “OBD II” in the Job Menu. The tool will automatically start a check of the vehicle's computer to determine which type of communication protocol it is using. When the tool identifies the computer's communication protocol, a communication link is established and then the screen will display the Monitor Status.

4.7.3.1 Read Codes

This option is used to identify which section of the emission control system has malfunctioned.

4.7.3.2 Erase Codes

After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicle's ignition key is in the ON position with the engine off.

Notes:

  • Before performing this function, make sure to retrieve and record the trouble codes.
  • After clearing, you should retrieve trouble codes once more or turn ignition on and retrieve codes again. If there are still some trouble codes in the system, please troubleshoot the code using a factory diagnosis guide, then clear the code and recheck.
4.7.3.3 I/M Readiness

I/M refers to Inspection and Maintenance that is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.

4.7.3.4 Data Stream

This option retrieves and displays live data and parameters from the vehicle's ECU. The data can be viewed in Value, Graph, or Combine mode.

4.7.3.5 View Freeze Frame

When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.

Note: If DTCs were erased, Freeze Data may not be stored in vehicle memory depending on vehicle.

4.7.3.6 O2 sensor test

The results of O2 sensor test are not live values but instead the results of the ECU's last O2 sensor test. For live O2 sensor readings, refer to any of the live sensor screens such as Graph Screen.

4.7.3.7 On-board monitor test

This function can be utilized to read the results of on-board diagnostic monitoring tests for specific components/systems.

4.7.3.8 EVAP System Test

The EVAP test function lets you initiate a leak test for the vehicle's EVAP system. The tool does not perform the leak test, but signals to vehicle's on-board computer to initiate the test.

4.7.3.9 Vehicle Info

This option displays the vehicle information, such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration Verification Number).

4.8 History

Generally once a vehicle diagnosis is performed, the tool will record the every details of diagnostic session. The History function provides direct access to the previously tested vehicles and users can resume from the last operation, without starting from scratch.

5. Maintenance and Special Functions (Reset Services)

In addition to amazing & powerful diagnostic function, the tool also features various service functions. It offers coding, reset, relearn and more service functions, to help vehicles get back to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model.

There are two methods to reset service lamp: Manual Reset or Auto Reset. Auto Reset follows the principle of sending command from the tool to vehicle's ECU to do resetting. While using Manual Reset, users just follow the on-screen instructions to select appropriate execution options, enter correct data or values, and perform necessary actions, the system will guide you through the complete performance for various service operations.

Image showing 31+ hot special services available on the LAUNCH CRP919X, including Oil Reset, SAS, EPB, BMS, DPF, ABS, Injector Coding, Power Balance, Gear Learning, Coolant Bleeding, Windows Calibration, Suspension Reset, EGR Reset, IMMO Key, TPMS, Throttle, Seat, and more.
Figure 7: Overview of 31+ Hot Special Services.

5.1 Oil Reset Service

This function enables you to reset the oil service for the engine oil life system, which calculates an optimal oil life change interval depending on the vehicle driving conditions and weather events.

5.2 Electronic Parking Brake Reset

This function enables you to reset the brake pad after replacing the brake pad.

5.3 Steering Angle Calibration

This function enables you to reset the steering angle, after replacing the steering angle position sensor, replacing steering mechanical parts, performing four-wheel alignment, or recovering car body.

5.4 ABS Bleeding

This function allows you to perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS).

5.5 Gear Learning

This function enables you to perform tooth learning for the car, to turn off the MIL.

5.6 IMMO Service

This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

5.7 Injector Coding

This function enables you to write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder, so as to more accurately control or correct cylinder injection quantity.

5.8 Battery Maintenance System Reset

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

5.9 Diesel Particulate Filter (DPF) Regeneration

This function enables you to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode to stabilize the filter performance.

5.10 Electronic Throttle Position Reset

This function enables you to make initial settings to throttle actuators and returns the learned values stored on ECU to the default state.

5.11 Gearbox Matching

This function enables you to complete the gearbox self-learning to improve gear shifting quality.

5.12 AFS (Adaptive Front-lighting System) Reset

This function enables you to initialize the adaptive headlamp system.

5.13 Sunroof Initialization

This function enables you to set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc.

5.14 Suspension Calibration

This function enables you to adjust the height of the body.

5.15 EGR Adaption

This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.

5.16 Seats Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

5.17 Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

5.18 Coolant Bleed

Use this function to activate the electronic water pump before venting the cooling system.

5.19 AdBlue Reset (Diesel Engine Exhaust Gas Filter)

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

5.20 NOx Sensor Reset

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.

5.21 AC System Initialization

AC system relearn/initialization must be performed when the vehicle AC ECU or actuator is replaced or the ECU memory is lost.

5.22 High Voltage Battery Detection

This function is used for high voltage battery diagnosis and status information detection.

5.23 Windows Calibration

This function is used to perform door window matching to recover the ECU initial memory, and recover the automatic ascending and descending function of power window.

5.24 Language Change

This function is used to change system language of vehicle center console.

5.25 A/F Reset

This function is applied to set or learn air/fuel rate parameters.

5.26 Transport Mode

To lower vehicle power consumption, user may perform the following operations: limit vehicle speed, not wake up the network for door open and disable remote key etc. In this case, deactivating transport mode is needed to recover vehicle being normal.

5.27 Stop/Start Reset

This function is used to open or close the automatic Start/Stop function via setting the hidden function in ECU (The precondition is vehicle equipped with hidden function and hardware support).

5.28 Intelligent Cruise Control System Reset

This function is used to matching the intelligent cruise control module after it is replaced or repaired.

5.29 Engine Power Balance Monitoring

This function is used to monitor crankshaft acceleration in the power stroke of each cylinder, to determine the relative power provided by each cylinder.

5.30 Gas Particulate Filter (GPF) Regeneration

This function is used to perform the GPF replacement or regeneration after the fuel consumption is increased and engine output power is reduced resulting from a long time service of the GPF.

5.31 Motor Angle Calibration

This function is used to perform the motor angle calibration when the rotor position detected by the motor angle position sensor is different from the actual rotor field position.

6. Data Management

6.1 Diagnostic Report

This module stores all diagnostic reports generated in process of vehicle diagnosis. All the diagnostic reports are sorted by Date and Make. If there are too many reports stored, tap (Search) to filter and quickly locate it.

  • To select certain report, just check the box at the right lower corner of the report. To select all reports, tap “Select All". To deselect all, tap "Unselect".
  • Tap it to view its details.
  • Select the desired report and then tap "Delete" to delete it.

6.2 Diagnostic Record

If user records the running parameters or waveform graphs while reading data stream, it will be saved as diagnostic records and appear under this tab. Tap "Diagnostic Record" to enter and select the desired data stream items and tap "OK" to jump to the playback page.

On-screen Buttons:

  • Graph: Displays the parameters in waveform graphs.
  • Combine: This option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors.
  • Value: This is the default mode which displays the parameters in texts and shows in list format.
  • Frame Playback: Plays back the recorded data stream items frame by frame.

6.3 DTC Library

This option helps you to find the location of the vehicle's DLC.

This option helps you to find the location of the vehicle's DLC.

6.5 Feedback

This item allows you to feedback your diagnostic problems to us for analysis and troubleshooting.

Tap "Feedback", the following 3 options will be displayed on the left column of the screen.

6.5.1 Feedback

Tap a tested vehicle model to enter the feedback screen.

  1. Tap "Choose File" to open the target folder and choose the desired diagnostic logs.
  2. Choose the failure type and fill in the detailed failure description in the blank text box and telephone or email address. After inputting, tap “Submit Result" to send it to us.

6.5.2 History

Tap it to view all diagnostic feedback records. Different process states are marked with different colors.

6.5.3 Offline list

Tap it to display all diagnostic feedback logs which have not been submitted successfully due to network failure. Once the tool gets a stable network signal, it will be uploaded to the remote server automatically.

6.6 Firmware Fix

Use this item to upgrade and fix diagnostic firmware. During fixing, please do not cut power or switch to other interfaces.

6.7 Image

This option allows you to manage or share the screenshots.

6.8 I/M Readiness

This option allows you to check whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.

7. Upgrade

If some new software or APK can be updated, a numeric indicator will display on the Upgrade module on the Job menu. In this case, you may use this option to keep it synchronized with the latest version.

Notes:

  • To enjoy more functions and better service, you are strongly suggested to update it on regular basis.
  • This function requires a stable network connection.

Tap Upgrade on the Job menu to enter the update center.

By default, all diagnostic software is selected. To deselect certain software, tap Unselect, and then check the box next to vehicle model. Tap Update to start downloading. It may take several minutes to finish it, please be patient to wait. To pause downloading, tap Stop. To resume it, tap Continue. If network connection failure occurs, tap Retry to try again. Once download is finished, the software packages will be installed automatically.

Video 1: Product overview and feature demonstration.

8. Add-on Modules

There are two add-on modules available for extending the functions of the tool. Each module consists of two parts: hardware and app. These modules cannot work properly on the tool, which need to work with the specific compatible hardware (sold separately).

8.1 BST (Battery System Test)

Battery test is specifically designed to help car owner, repair workshop, battery factory determine whether the battery is normal or not. It supports various battery standards and specifications, including CCA, DIN, IEC, EN, JIS, SAE and GB etc.

Two test modes (Out-of-car Inspection & In-car Inspection) are available for battery test.

Out-of-car inspection indicates that the battery is disconnected from all loading devices on vehicles. Only the Battery Health Test is supported for this inspection.

Diagram showing the BST360 battery tester connected to a car battery for in-car inspection.
Figure 8: BST360 Battery Tester for in-car inspection.

In-car inspection indicates that the battery connects to loading devices, such as engine, etc. In this mode, the following tests can be done in a sequence of Battery Health Test, Start System Test and Charging Health Test.

8.1.1 Connection

Clamp the BLACK and RED clips of the battery clamps cable on the Negative (-) and Positive (+) terminals of the vehicle battery respectively.

8.1.2 Battery Health Test

It is used to analyze the health status of the automobile battery, calculate the actual cold starting ability of the battery, judge the aging degree of the battery, and provide reliable analysis basis for the test and maintenance of the battery.

  1. After connection is properly done, go to [BTS] and select [Battery Health Test].
  2. The system will automatically connect the Bluetooth BST360 battery tester (sold separately).
  3. Select the correct battery type: After connection is successful, the system will enter the following screen.

Note: Select the desired battery type referring to the following methods.

  1. For batteries printed with the word AGM or VRLA, please choose “AGM Spiral” or “AGM Start/Stop Battery”.
  2. For batteries printed with the word GEL (seldom used), please choose “GEL Battery”.
  3. For batteries printed with the word EFB, please choose “EFB Battery”.

For other batteries not printed such words, please select the "Common Battery".

  1. Detect floating electricity. The floating electricity indicates the virtual power left by the car when it is started. If the floating electricity is detected, please turn on the headlamp to remove it.
  2. Select the correct battery testing standard and capacity (alternatively user can also directly drag the slide to change the battery capacity).
  3. Output the test result.

There are total 5 battery test conclusions, which are displayed at the end of the test report:

  1. Good battery: Indicates that the battery is normal.
  2. Replace battery: Indicates that the battery is aged or becomes rejected, or battery life cycle is nearly exhausted.
  3. Good-recharge: Stands for low battery. The battery is good itself.
  4. Charge-retest: It is better for a few batteries to be fully charged before testing in order to avoid judging in error under special conditions.
  5. Bad cell: Indicates one of the battery cells is bad and cannot work normally, but for which one is bad, it can't be verified.

8.1.3 Start System Test

It is mainly to detect and analyze the starting motor, detect the actual starting current and starting voltage required by the starting motor, so as to judge whether the starting motor is normal or not.

  1. After connection is properly done, go to [BTS] and select [Start System Test].
  2. Turn off all electrical components, including lights, radio and A/C etc. and stop the engine before test, tap [Confirm] to confirm.
  3. Start the engine according to the prompts on the screen. After the start, the system will display the start voltage test result.

8.1.4 Charging Health Test

This function mainly detects and analyzes the vehicle charging system, including generator, rectifier, rectifier diode, etc. Through this test, we can know that the output voltage of the generator, the rectifier diode, and the charging current is normal or not respectively.

  1. After connection is properly done, go to [BTS] and select [Charging Health Test].
  2. Start the engine and start charging until the charging voltage and ripple are normal.
  3. According to the on-screen prompts, press the accelerator and increase the engine speed to 2500rpm for 5 seconds.
  4. Output the test result.

8.1.5 Precautions on battery test

  • The accuracy of battery voltage, charging voltage, start voltage is 0.01V in test results; CCA (Cold Cranking Amps) precision is 5CCA. Generally, charging voltage value is greater than starting voltage.
  • Starting voltage range: The value higher than 9.6V is normal, otherwise it is too low.
  • Generally, the voltage is lower than 11V for the bad cell battery, but it is possible that the battery is completely exhausted or has a serious low capacity.
  • It has no influence on test result in the event that engine's output voltage or engine revolution is not very stable.
  • Pay more attention to connect the clip. The battery poles connect with conductor, which makes the clip has a poor connection when testing battery.

8.2 TPMS (Tire Pressure Monitoring System)

This module allows you to configure the tablet as TPMS activation & diagnostic tool, which provides the ability to trigger TPMS sensor, program TPMS sensor, perform the relearning procedure. It needs to work with the X-431 TSGUN device (sold separately).

For more details, please refer to the User Manual included with the module.

9. User Tips

  • Verify Authenticity: Ensure you purchase the original LAUNCH CRP919X to guarantee full functionality and support.
  • Update Frequency & Cost: The device comes with 2 years of free updates. After this period, updates may require a subscription. Check with your vendor for current pricing and update schedules.
  • Vehicle Compatibility: Always confirm compatibility with your specific vehicle make, model, and year, especially for advanced functions like ECU coding. The global version is designed for wide compatibility, but specific regional models (e.g., Nissan Rogue, Mercedes GLB 2024) should be verified.
  • Regional Use: The global version is designed for worldwide use, including regions like Africa (e.g., Namibia). However, specific vehicle models and their regional variations might have unique requirements.
  • Network Connection: A stable internet connection is crucial for updates, VIN auto-detection, and certain diagnostic functions.

10. Troubleshooting (FAQ)

10.1 System halts when reading data stream. What is the reason?

It may be caused by a slackened connector. Please turn this tool off, firmly connect the connector, and switch it on again.

10.2 Screen of main unit flashes at engine ignition start.

Caused by electromagnetic disturbing, and this is normal phenomenon.

10.3 There is no response when communicating with on-board computer.

Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.

10.4 What to do if the system fails to start auto VIN detection?

Please check the following possible reasons:

  • Whether the tool is properly connected to the vehicle's DLC.
  • Whether the "Automatic detection on Connect" switch is OFF. If yes, slide it to ON.

10.5 Why are there so many fault codes?

Usually, it's caused by poor connection or fault circuit grounding.

10.6 How to upgrade the system software?

  1. Switch the tool on and ensure a stable internet connection.
  2. Tap "Setting" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version" to enter the system upgrading page.
  3. Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed, please be patient. After upgrade is successfully finished, the tool will automatically restart and enters the Job menu.

10.7 What if the tool cannot be switched on even after a period of recharging?

Please recharge it for at least 3 hours until the power LED lights up, then it can be switched on.

11. Specifications

AttributeValue
Operating SystemAndroid 10.0
ProcessorPowerful Quad-Core Processor
RAM3GB
ROM32GB
Display7 inch IPS touch screen (1024x600 resolution)
ConnectivityMini USB 2.0, Wi-Fi
Battery6100mAh lithium-polymer battery
Battery LifeMore than 8 hours
Product Dimensions251.4mm x 150.6mm x 40.4mm (9.8 x 5.5 x 1.5 inches)
Product Net Weight<600g (1.54 lbs)
Item Weight6.45 pounds (including packaging)
OBDII Input Voltage Range9~18V
Input MethodTouch & Keypad
Working Temperature-10 to 50°C (14 to 122°F)
Storage Temperature-20 to 70°C (-4 to 158°F)
Wireless FunctionYes
Wireless SupportWifi
Battery IncludedYes
Free Update2 Years Free Update
Warranty5 Years

12. Warranty and Support

12.1 Warranty

THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER'S BUSINESS.

LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.

This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.

12.2 Order Information

Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Your order should include the following information:

  1. Quantity
  2. Part number
  3. Item description

12.3 Customer Service

If you have any questions on the operation of the unit, please contact local dealer, or contact LAUNCH TECH CO., LTD:

Tel: 86-755-25938674

E-mail: DOD@cnlaunch.com

Statement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable, if you have any question, please contact local dealer or LAUNCH TECH CO., LTD., LAUNCH does not bear any responsibility arising from misunderstandings.

For a complete digital version of the user manual, please refer to the official PDF document: User Manual (PDF)


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.