HOTO H-D50

Contents

HOTO Smart Laser Measure Pro User Manual

Model: H-D50

01 Product Overview

Please read this manual carefully before using the product and keep it for future reference. Thank you for using HOTO Smart Laser Measure Pro.

Diagram of HOTO Smart Laser Measure Pro with numbered parts
Figure 1: HOTO Smart Laser Measure Pro Components
  • 1. Laser receiver lens: Receives the laser beam for measurement.
  • 2. Laser emission lens: Emits the laser beam.
  • 3. Display: Shows measurement data and device status.
  • 4. Mode switching button: Used to cycle through measurement modes.
  • 5. Power/Measure button: Turns the device on/off and initiates measurements.
  • 6. Metal lanyard hole: For attaching a lanyard.
  • 7. Type-C charging port: For charging the device.

02 Display

Diagram of HOTO Smart Laser Measure Pro display with numbered indicators
Figure 2: Display Indicators
  • 1. Measuring basis/Laser emission alert: Indicates the reference point for measurement and if the laser is active.
  • 2. Battery indicator: Shows the current battery level.
  • 3. Bluetooth connection: Indicates Bluetooth status (flashing when searching, solid when connected).
  • 4. Measuring angles in real time: Displays the current angle measurement.
  • 5. Measurement history - Group 1: First line of measurement history.
  • 6. Measurement history - Group 2: Second line of measurement history.
  • 7. Measurement history - Group 3: Third line of measurement history.
  • 8. Real-time measurement data: Displays the current measurement value.
  • 9. Measurement unit: Shows the active unit of measurement (e.g., m, ft).

03 Setup and Operation

Turning On/Off

  • Power-on: In the power-off state, press the power/measure button for more than 1 second to start the tool. The display will light up and enter test mode.
  • Power-off: In the power-on state, press the power/measure button for more than 3 seconds to turn off the tool.
  • The product will automatically turn off if inactive for 180 seconds.

Vibration Feedback

  • The instrument vibrates once when manually powered on/off.
  • The instrument vibrates once when the switch is flipped to change modes.
  • The instrument vibrates once when a measurement is finished.

Mode Switching

  • Flip the mode switching button (4) down to cycle through modes in this order: Distance Measurement > Angle Measurement > Angles and Height Measurement > Size Measurement > Virtual Scale.
  • Flip the mode switching button (4) upwards to change modes in reverse order.

Measuring Distance

  • After starting the product, short press the power/measure button (5). The tool will emit a laser and measure the distance. The current distance will be displayed in real time.
  • Press the power/measure button (5) again to stop laser emission. The fixed numbers will show the final measurement values.

Measuring Angles

  • Flip the mode switching button (4) up or down to launch the Angle Measuring mode. The angle is displayed in real time.
  • Press the power/measure button (5) again to stop laser emission. Numbers will stop to show measurement values.

Measuring Angles and Height

  • Flip the mode switching button (4) up and down to initiate the Angle and Height Measurement mode.
  • Short press the power/measure button (5) once to emit laser. The measurement will be conducted in real time and seen on the display.
  • Press the power/measure button (5) again to stop laser emission. The number will stop and show the measurement data of a triangle's hypotenuse and inclination. After measuring the hypotenuse and inclination, the instrument will automatically calculate the height and horizontal distance.
  • To continue the measurement, short press the power/measure button (5) again.

Measuring Size (Area)

  • Flip the mode switching button (4) up or down to enter the Size Measurement mode.
  • Short press the power/measure button (5) once to emit laser. The measurement will be conducted in real time and seen on the display. Press the power/measure button (5) again to stop laser emission. The measurement shows the rectangle's length.
  • Use the same method to measure the rectangle's width, and the instrument will automatically calculate the rectangle's size (area).
  • To continue the measurement, short press the power/measure button (5) again.

Virtual Scale

  • Flip the mode switching button (4) up or down to launch the Virtual Scale mode.
  • Short press the power/measure button (5) once to emit laser. The measurement will be conducted in real time. The default unit is cm.
  • Press the power/measure button (5) again to stop laser emission, and the number will stop and show the measurement data.
  • The minimum adjustable length is 0.2 m and the maximum length is 50 m.
Examples of different measurement modes displayed on the HOTO Smart Laser Measure Pro screen
Figure 3: Various Measurement Displays (Distance, Angle, Size, Virtual Scale)

Connecting to the HOTO App

Scan the product's QR code or search for "HOTO app" in your app store. Download and install the HOTO app. If the app was previously installed, you will be directed to the device connection page.

QR code for downloading the HOTO app
Figure 4: HOTO App QR Code

Bluetooth Connection

  • Bluetooth is on by default and cannot be turned off manually. The screen will show a Bluetooth icon.
  • Bluetooth will automatically turn on when the product is started, displaying a flashing Bluetooth icon. The HOTO app will automatically search for devices to pair with.
  • When the product is started, open the HOTO app and click the upper right corner to add a device. Follow the steps, and the Bluetooth icon will be permanently lit on when the connection is successful.
  • If the connection fails within 180 seconds, Bluetooth will automatically turn off to save energy.
  • Note: HOTO Smart Laser Measure Pro has a non-independent and complete Bluetooth module with CMIIT ID: 2020DP2859.

Switching Reference Plane

By default, the reference plane of the product is the end reference. Please use the product end as the reference plane. To use the front reference, switch the reference plane in Product Settings - Rangefinder Settings in the app.

Changing Measurement Units

The product supports three measurement units, with "m" (meters) by default.

  • Length units: 0.000m, 0.000ft, 0' 00" 1/16
  • Size units: 0.000m^2, 0.000ft^2, 0.000ft^2

To use ft (foot) or 0' 00" 1/16 (foot, inch, 1/16), please switch the measurement units in Product Settings found in the app.

Bluetooth Reset

When the laser measure is on/off, press and hold the power/measure button for 7 seconds, and the screen displays "RESET" and a checkmark icon to reset the product's Bluetooth network configuration information.

Charging

  • This rangefinder is equipped with a universal Type-C charging port and comes with a USB charging cable.
  • If it has not been used for a long time, fully charge the product before use.
  • The tool does not measure during the charging process.

User Tips

  • The HOTO app enhances functionality, allowing for easy connection, instant updates, and the ability to retitle measurements for future reference.
  • The device offers various measurement options including length, angles, and area, and supports different metric systems, making it versatile for diverse tasks.
  • The vibration feedback upon measurement completion is a useful feature, confirming the action without needing to constantly look at the screen.
  • For optimal accuracy, this laser measure is best suited for indoor use.
  • The device is noted for its sturdy build quality, providing a premium feel.

04 Warnings

Important: Read the safety and operating instructions carefully before using the laser measure for the first time.

  • Failure to use the laser measure in accordance with the instructions in this manual may lead to damage to the device, decreased measurement accuracy, or injuries.
  • Do not attempt to disassemble or repair the laser measure yourself. Do not illegally modify or change the laser emitting performance. Store the laser measure properly and keep it out of reach of children and unauthorized persons.
  • Do not point the laser light at your eyes or other body parts, or those of other people. Never aim the laser light at highly reflective surfaces.
  • Do not use the laser measure near aircraft or medical equipment, or in flammable or explosive environments, as its electromagnetic radiation may interfere with other devices.
  • Do not dispose of used batteries and unusable laser measures with household waste. Dispose of them according to national or local laws and regulations.
Laser radiation warning symbol: Class 2 Laser Product, Do Not Stare Into Beam
Figure 5: Laser Radiation Warning

LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Maximum output of laser radiation <1 mW
Wavelength 630-680 nm
IEC 60825-1:2014; EN 60825-1:2014

05 Troubleshooting

When the product is in use, the following indicators or issues may appear in the main display area:

ErrorCauseSolution
Quick flashing of the lightning bolt signThe battery level is low.Charge the laser measure.
Unable to chargeCharging temperature protectionIt is recommended to charge at a normal temperature of about 25°C.
Couldn't measure and the display shows "-.---"The laser reflective signal is too weak (e.g., when measuring black surfaces).Measure a target with high reflectivity or use the laser measure with a reflective board.
The laser reflective signal is too strong (e.g., when measuring highly reflective surfaces).Measure a target with low reflectivity or use the laser measure with a reflective board.
Out of the operating temperature range.Use the laser measure within the specified temperature range.
Out of measurement range.Use the laser measure within the measurement range.

06 Specifications

Model:H-D50
Measurement Range:0.05-50 m
Measurement Accuracy:±(2 mm+D*1/10000)
Analog Ruler Scale Accuracy:±(4 mm+D*1/10000)
Minimum Displaying Unit:0.001 m
Measurement Unit:m/ft
Laser Type:630-680 nm wavelength
Lithium-ion Battery:3.7 V⎯ 850 mAh
Display Screen:1.77-inch LCD screen
Charging Input:5 V⎯ 1 A
Operating Power:1 W (MAX.)
Charging Time:Approx. 100 min
Automatic Turn-off Time:180 s
Automatic Laser Off Time:180 s
Operating Temperature:-10°C to 50°C
Storage Temperature:-20°C to 60°C
Storage Humidity:20%-80% RH
Item Dimensions:99.5×44.1×23.3 mm
Net Weight:Approx. 90 g
Bluetooth Transmission Distance:Approx. 8 m

Note: In the analog ruler mode, the test accuracy is ±4mm.
"D" refers to the actual distance in an indoor environment with standard reflective surfaces.
All data produced by this product may vary slightly due to different actual measurement environments and should depend on users' actual measurements. The rangefinder is appropriate for indoor measurements. The measurement results may have relatively wide discrepancies in harsh environments such as extremely strong sunlight, excessively fluctuated temperature, weak reflective surfaces, and low battery power. The measuring range of 0.05m is the minimum measurable distance using head-based reference mode.

Compliance Information

WEEE Directive (2012/19/EU)

WEEE symbol and CE mark
Figure 6: WEEE Symbol and CE Mark

All products bearing the WEEE symbol (Waste Electrical and Electronic Equipment) should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

CE Declaration of Conformity

Shanghai HOTO Technology Co., Ltd. hereby declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments, including:

  • 2014/53/EU The Machinery Directive
  • EN 62479:2010
  • EN 61010-1:2010
  • ETSI EN 301 489-1 V2.2.3:2019
  • ETSI EN 301 489-17 V3.2.2:2019
  • EN 61326-1:2013
  • EN 61000-3-2:2019
  • EN 61000-3-3:2013+A1:2019
  • ETSI EN 300 328 V2.2.2:2018
  • 20011/65/EU+ (EU) 2015/863 Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Federal Communications Commission (FCC) Supplier's Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Warranty and Support

For product support, technical assistance, or warranty inquiries, please contact the manufacturer or your local distributor.

Manufacturer: Shanghai HOTO Technology Co., Ltd.

Address: Building 45, No. 50 Moganshan Rd, Putuo District, Shanghai, PRC, 200060.

A user manual in PDF format is available for download. Please refer to the official product page or contact support for the link: User manual (PDF)

Frequently Asked Questions (FAQ)

Q: Does it have distance measurement? Can it also be used as a protractor to know the angles of inclination?
A: Yes, the HOTO Smart Laser Measure Pro supports distance measurement. It also features an Angle Measurement mode and an Angles and Height Measurement mode, allowing it to function as a digital protractor for inclination angles.
Q: Does the 50-meter model have continuous measurement (so that in one measurement it can determine the maximum and minimum value)?
A: The device provides real-time measurement data, which can be used to observe continuous changes. While it displays real-time values, specific max/min value tracking in a single continuous measurement might be a feature of the companion app.
Q: Is it Bluetooth enabled?
A: Yes, the HOTO Smart Laser Measure Pro has Bluetooth connectivity to connect with the HOTO app for extended functionalities.
Q: Does it have level measurement? Does it have an iOS app?
A: The device measures angles, which can be used for leveling purposes. Yes, there is an official HOTO app available for iOS devices.
Q: Does it measure in feet and inches?
A: Yes, the device supports measurement in feet (ft) and feet-inches (0' 00" 1/16). You can switch the measurement units in the Product Settings within the HOTO app.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.