FMS FCX24M

Contents

FMS FCX24M 1/24 RC Land Rover Series Instruction Manual

Model: FCX24M | Brand: FMS

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your FMS FCX24M 1/24 RC Land Rover Series vehicle.

1. Safety Precautions

1.1. Disclaimer and Warning

Thank you for purchasing our product. This product is composed of precision components and is not a toy. It is not suitable for use by individuals under the age of 14. Please do not allow children to come into contact with this product. Exercise extra caution when operating this product in the presence of children.

This product is a remote-controlled model and will provide a smooth and easy operating experience when the power is functioning correctly, and all components are undamaged. We reserve the right to update this manual without separate notification.

Before using the product, please carefully read this product manual to understand your legal rights, responsibilities, and safety instructions. Failure to do so may result in property damage, safety incidents, and personal safety risks. Once you use this product, it is considered that you have understood, accepted, and agreed to all the terms and content of this manual. Users are responsible for their actions and all consequences arising from them.

1.2. General Safety Guidelines

  • Always turn on the transmitter before connecting the battery on the model. When turning off the model, always disconnect the battery first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable and cause serious damage.
  • Never allow transmitter batteries to run low as it may cause loss of vehicle control.
  • Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold climate. Do not store the model near any source of heat such as oven or heater. Store the model indoors, in a climate-controlled, room temperature environment.
  • Replace damaged components with original factory-parts. Pay special attention to the polarity of all vehicle wiring.
  • Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible for their actions.
  • The product is composed of precision electrical components. It is critical to keep the product away from moisture and other contaminants.
  • Always check the radio range of the vehicle prior to operation in order to prevent radio loss or interference.
  • Operate this product within your ability. If the vehicle is dangerous to retrieve, it is never worth the risk.
  • Do not use the product at night or in bad weather like rain or thunderstorm. It can cause erratic operation or loss of control.
  • Do not use the product when visibility is limited.
  • Do not use the product on rain or snow days. Any exposure to moisture (water or snow) may cause erratic operation or loss of control.
  • Do not touch any part of the model that may generate heat during operation, or immediately after use. The engine, motor or speed control, may be very hot and can cause serious burns.
  • Do not operate this product when you are tired, uncomfortable, or under the influence of alcohol or drugs. Doing so may cause serious injury to yourself or others.
  • The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large object can block the RF signal and lead to loss of control.

2. Product Overview

The FMS FCX24M 1/24 RC Land Rover Series models are designed to faithfully reproduce the details of the iconic Land Rover vehicles in 1/24 scale. These models feature hard plastic car shells, detachable components for customization, and come with their own roof racks, which can be optionally equipped with scale parts like fuel drums, spare tires, equipment boxes, and recovery boards.

Both the front and rear lights as well as the roof-mounted searchlights have designated lamp positions, making it easy to install lighting systems (headlights are pre-installed).

The FCX24M chassis features a non-bearing trapezoidal metal beam with solid front and rear axles. It utilizes a two-speed transmission, delivering impressive power under the drive of the 050 motor, with ample torque and speed. The 380mAh 2S LiPo battery supports a 30-minute high-speed driving experience.

These 1/24 scale cars are versatile, suitable for both indoor and outdoor play. They can navigate various terrains, from household obstacles to natural outdoor environments.

Video: FMS FCX24M Land Rover Series in action, showcasing its off-road capabilities and various models.

FMS FCX24M Land Rover series RC vehicles on a rocky terrain

Image: FMS FCX24M Land Rover series RC vehicles on a rocky terrain, highlighting the Range Rover and Defender models.

Underside view of the FCX24M chassis showing the backpropagation structure

Image: Underside view of the FCX24M chassis, illustrating the backpropagation structure which reduces shaft effects for a more simulated climbing posture.

3. Setup

3.1. Transmitter Battery Installation

The transmitter has a built-in antenna. It requires 4 AAA batteries for operation. Follow these steps:

  1. Open the battery compartment cover.
  2. Insert 4 AAA batteries with the correct polarity. Ensure the metal terminals connect properly.
  3. Replace the battery compartment cover.

Low Battery Alarm:

When the battery voltage is lower than 4.2V, the transmitter will emit an alarm, and the LED will flash slowly.

3.2. Receiver and Servo Installation

Ensure the receiver is mounted in an appropriate location within the model to ensure a stable signal. Pay attention to the following:

  • Make sure the receiver is not installed near ESCs or other sources of electrical noise.
  • Keep the receiver's antenna away from conductive materials such as carbon or metal. To ensure normal function, maintain a gap of at least 1cm between the antenna and conductive material.
  • Do not pull the antenna of the receiver. Do not tie the antenna and the servo cable together.
  • Do not power on the receiver during the setup process to prevent damage.

3.3. Connecting the Vehicle Battery

The vehicle uses a 2S LiPo battery. Follow these steps to connect it:

  1. Release the hook and loop fastener to separate the shell body from the chassis from the front end.
  2. Load the battery into the battery compartment.
  3. Connect the battery plug (51005 2P Male) to the female connector of the receiver/ESC combo unit.
  4. Close the engine hood.

Note:

  • If not in use for a long time, unplug and remove the battery to prevent leakage.
  • Do not open, disassemble, or attempt to repair the battery.
  • The battery needs to be disconnected from the vehicle before it can be charged.
  • Do not charge the battery while it is in the vehicle.

3.4. Spare Tire Installation

Install the spare tire using the included hex screw and spacer as shown in the diagram.

Diagram for spare tire installation

Image: Diagram illustrating the correct method for installing the spare tire using a hex screw and spacer.

4. Operating Instructions

4.1. Power-on and Power-off

Power-on Sequence:

  1. Check that the transmitter batteries are fully charged and correctly installed.
  2. Toggle the transmitter's Power Switch to the [ON] position. The LED will be solid on.
  3. Connect the receiver to power (vehicle battery).

Power-off Sequence:

  1. Disconnect the receiver power (vehicle battery).
  2. Toggle the transmitter's Power Switch to the [OFF] position.

Important: For safety, always power on the transmitter before the receiver and power off the receiver before the transmitter.

4.2. Binding the Transmitter and Receiver

The transmitter and receiver are factory-bound. If re-binding is necessary (e.g., replacing receiver), follow these steps:

  1. Turn on the transmitter while holding the BIND button to put it into bind mode. The LED will flash quickly. Release the BIND button.
  2. Power on the receiver. It will automatically enter binding state if no connection is found within 1 second.
  3. The receiver's LED will turn solid on, indicating successful binding.
  4. Check that the transmitter and receiver functions are working correctly. Repeat steps 1-3 if any problems arise.

Note:

  • If binding is not completed within ten seconds, the receiver's LED will enter its slow flashing state.
  • The transmitter's LED status indicates its power supply and working state: Off (not powered), Slow flashing (low voltage), Fast flashing (bind mode), Gradual (sleep/idle alarm), Three-flash-one-off (standby).

4.3. Transmitter Controls (FMS-G3)

Transmitter diagram with labeled components

Image: Diagram of the FMS-G3 transmitter with labeled components for steering, throttle, switches, and buttons.

Transmitter Control Functions
Channel Assigned Control Function
CH1 Steering Wheel Controls car direction (right/left).
CH2 Throttle Trigger Controls car movement (forward/backward).
CH3 Three-position Switch Switches between fast, median, and slow speed positions.

Other Buttons:

  • ST- Button: Decreases trim and travel value of CH1.
  • TH- Button: Decreases trim and travel value of CH2.
  • Power Switch: Turns the transmitter on/off.
  • REV Button: Reverses CH1 or CH2 direction.
  • ST+ Button: Increases trim and travel value of CH1.
  • TH+ Button: Increases trim and travel value of CH2.
  • BIND Button: Used for binding, turning car lights on/off, or resetting data.

4.4. Stick Calibration

This function sets the neutral position for the throttle trigger and steering wheel. While factory-calibrated, recalibration can be done:

  1. Turn and hold the wheel clockwise to its max travel point and push the throttle forwards as far as possible. Then, turn on the transmitter to enter calibration mode (buzzer sounds in cycle).
  2. Turn the steering wheel to max and min travel points (clockwise and counterclockwise). Then push/pull the trigger to forward/backward as far as it will go.
  3. Return the wheel and trigger to the neutral position. Press the BIND button to save and exit.

4.5. Channel Reverse

To reverse the output direction of a channel:

  • For CH1 (Steering): With the steering wheel at maximum or minimum travel, press the REV button. Each press switches the direction.
  • For CH2 (Throttle): With the throttle trigger at maximum or minimum travel and the steering wheel in the neutral position, press the REV button. Each press switches the direction.

A short buzzer sound confirms the reverse action. Be cautious when reversing the throttle channel, as the model car will move at full speed if the trigger is at full throttle position.

4.6. Trim Setting

To adjust the trim value of a channel:

  • For CH1 (Steering): With the steering wheel in the neutral position, press the ST+/- button.
  • For CH2 (Throttle): With the throttle trigger in the neutral position, press the TH+/- button.

ST+/TH+ increases trim, ST-/TH- decreases trim. Trim range: -150 us to 150 us, step 5us, default 0. A short buzzer sound confirms the setting. Continuous adjustment occurs by holding the button. Two beeps indicate passing the neutral position, and a long beep indicates reaching an endpoint.

4.7. D/R Setting (Dual Rate)

To adjust the travel range value of a channel:

  • For CH1 (Steering): With the steering wheel at maximum or minimum travel, press the ST+/- button.
  • For CH2 (Throttle): With the throttle trigger at maximum or minimum travel, press the TH+/- button.

ST+/TH+ increases travel, ST-/TH- decreases travel. Travel range: 0-120%, default 100%, step 5%. A short buzzer sound confirms the setting. Continuous adjustment occurs by holding the button, and a long beep indicates reaching an endpoint.

4.8. Car Light Control

When the receiver and transmitter are normally connected, press the BIND button on the transmitter to turn the car lights on or off. By default, the car light is off.

4.9. Drag Brake Function

To activate and adjust the drag brake function (default 0%):

  1. Under normal power-on, quickly press the REV button twice within 1 second to enter the mode. The green light will flash.
  2. Select the appropriate drag brake setting value (0%, 50%, 75%, 100%) by pressing the corresponding button (ST-/+, TH-/+).
  3. Quickly press the REV button twice within 1 second to exit.

Press the BIND button to cycle between with and without brake.

4.10. Trims and Travel of Gear Shift Servo

To adjust the trims and travel for the gear shift servo:

  1. Under normal power-on, quickly press the BIND button twice within 1 second to enter the mode. The green light will flash.
  2. Press the corresponding buttons (ST-/+, TH-/+) to adjust to the appropriate state.
  3. Quickly press the BIND button twice within 1 second to exit.

ST+/- adjusts the adjustment step, and TH+/- adjusts the servo travel.

5. Maintenance

  • Regularly inspect all components for damage. Replace any damaged parts with original factory-supplied components.
  • Keep the vehicle clean and free from dirt, dust, and debris. Use a soft brush or cloth to clean the exterior.
  • Avoid exposing the vehicle to extreme temperatures or moisture. Store it in a dry, climate-controlled environment.
  • Check all wiring and connections periodically to ensure they are secure and free from corrosion.
  • For battery care, always unplug and remove the battery if the vehicle will not be used for an extended period. Do not attempt to open, disassemble, or repair the battery. Always disconnect the battery from the vehicle before charging, and never charge the battery inside the vehicle.
  • After use, allow the battery pack to cool down to room temperature before recharging.
  • If the vehicle is involved in a crash, carefully inspect the battery and connectors for even the smallest damage.

6. Troubleshooting

6.1. Failsafe Setting

The failsafe function protects the model and personnel if the receiver loses signal. By default, CH2 enters brake mode, and the receiver outputs the last channel value. To set failsafe:

  • With the transmitter in normal working state, press and hold the BIND button for 3 seconds. The current channel value will be set as the failsafe value. A long buzzer sound confirms successful setting.

Note: Re-binding the transmitter and receiver will restore the failsafe setting to default.

6.2. Low Voltage Alarm

If the transmitter voltage drops below 4.2V, it enters a low voltage alarm state. The transmitter LED will flash slowly, and the buzzer will sound. For the safety of the system and model, the RF signal will turn off if the battery voltage drops below 3.5V.

6.3. Overheating Protection (Receiver)

The receiver has an overheating protection function. If the receiver temperature becomes too high, the CH2 motor channel will stop output, while the CH1 channel will continue normal output. Once the temperature returns to normal, the CH2 output will resume.

6.4. Offline Prompt

If the transmitter detects that the bound receiver has been turned off or disconnected for more than 2 seconds, the transmitter LED will show a three-flash-one-off state. The transmitter will exit this state once it receives information from the bound receiver again.

6.5. Reset Data

To reset the transmitter's function data to default values:

  • Press and hold both the BIND button and REV button while powering on the transmitter. A long buzzer sound will confirm the reset.

Note: Failsafe settings, binding information, and stick calibration data will not be reset by this action.

7. Specifications

7.1. General Product Specifications

  • Material: Metal, Plastic, ABS
  • Scale: 1:24
  • State of Assembly: Ready-to-Go
  • Power: Brushed 050 motor 35T
  • Charging Voltage: 7.4V
  • Is Electric: Lithium Battery
  • Certification: CE
  • Recommend Age: 14+ years
  • Package Includes: Original Box, Batteries, Operating Instructions, Remote Controller, USB Cable

7.2. Model-Specific Dimensions and Performance

Table of specifications for FCX24M series models

Image: Detailed specifications table for the FMS FCX24M Land Rover series, including Range Rover, Defender D110, Discovery, and Defender D90 models, covering dimensions, wheelbase, motor type, and tire size.

FCX24M Series Model Specifications
Product Name Color Shell Material Motor Type Tire Size (D*W) Wheelbase Highest Ground Clearance Product Size (L*W*H)
Range Rover first generation Yellow ABS Brushed 050 motor 35T 48mm*17mm 134mm 28mm 227*103*120mm
Defender D110 Yellow ABS Brushed 050 motor 35T 50mm*20mm 135mm 29mm 240*107*128mm
Discovery first generation Yellow ABS Brushed 050 motor 35T 48mm*17mm 134mm 28mm 232*105*133mm
Defender D90 Yellow ABS Brushed 050 motor 35T 50mm*20mm 111mm 24mm 214*107*128mm

7.3. Transmitter (FMS-G3) Specifications

  • Product Model: FMS-G3
  • Compatible Receivers: FMS-R3A
  • Compatible Models: 1:18, 1:24 simulation cars or climbing cars
  • Number of Channels: 3
  • RF: 2.4GHz ISM
  • Maximum Power: <20dBm (e.i.r.p.) (EU)
  • 2.4G Protocol: AFHDS 2A-BS
  • Distance: >100m (Ground distance without interference)
  • Resolution: 1024
  • Input Power: 6V DC or 1.5AAA*4
  • Working Current: 10mA (Static); 120mA/6V (Dynamic)
  • Charging Port: No
  • Low Voltage Alarm: < 4.2V
  • Antenna: Built-in single antenna
  • Data Port: No
  • Temperature Range: -10°C ~ +60°C
  • Humidity Range: 20%~95%
  • Online Update: No
  • Color: Blue
  • Dimensions: 115.2*75.5*145mm
  • Weight: About 113g
  • Certification: CE, FCC ID: 2A2UNG300

7.4. Receiver (FMS-R3A) Specifications

  • Product Model: FMS-R3A
  • Compatible Transmitters: FMS-G3
  • Compatible Models: 1:18/1:24 simulation cars or climbing cars
  • Applicable Motors: 050 motor set
  • PWM Channels: 2
  • Number of Lights: 1
  • RF: 2.4GHz ISM
  • 2.4GHz Protocol: AFHDS 2A-BS
  • Input Power: 2S LiPo battery
  • Continuous / Peak Current: 10A/40A
  • BEC Output: 5V/1A
  • Maximum Power: <20dBm (e.i.r.p.) (EU)
  • Distance: >100m (Ground distance without interference)
  • Antenna: External antenna
  • Data Output: PWM
  • Resolution: 1024
  • Temperature Range: -10°C ~ +60°C
  • Humidity Range: 20%~95%
  • Online Update: No
  • Dimensions: 32*24.4*12mm
  • Weight: 8g
  • WaterProof: PPX4
  • Certification: CE, FCC ID: 2A2UNR3A00

8. User Tips

  • The vehicle offers excellent value and performance, providing significant enjoyment for users.
  • Users find the vehicle enjoyable and fun to operate, with high-quality components despite its small size.
  • For enhanced crawling performance, adding weight to the wheels is recommended.
  • The two-speed transmission allows for both precise slow control and faster operation, making it versatile for different driving styles.
  • The vehicle is suitable for creating custom courses and is a great platform for upgrades and modifications.
  • Battery connectors can be challenging for younger users; consider leaving the charging cable connected under the chassis for easier access during recharging.
  • The car comes with a battery included in the package.
  • The vehicle features a dual-speed function for varied driving experiences.

9. Certifications and Support

9.1. Certifications

This product complies with relevant international standards:

  • CE Certification: The product is in compliance with RED 2014/53/EU.
  • FCC ID (Transmitter): 2A2UNG300
  • FCC ID (Receiver): 2A2UNR3A00

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

9.2. Item Guides & Documents

A detailed user manual in PDF format is available for download. Please refer to the official product page or contact customer support for the link.

The PDF manual can be found at: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.