CETANT PL230

Contents

LED Pendant Light User Manual

Model: PL230

Introduction

Thank you for purchasing the CETANT LED Pendant Light. This manual provides detailed instructions for the safe installation, operation, and maintenance of your new lighting fixture. Please read this manual thoroughly before installation and keep it for future reference.

Important Safety Information

  • Always disconnect the power supply at the main circuit breaker before installation, maintenance, or cleaning.
  • Installation should be performed by a qualified electrician or in accordance with local electrical codes.
  • Do not install the lamp in flammable or humid places.
  • Ensure all connections are secure and properly insulated.
  • Do not modify the lamp in any way.
  • This product is designed for indoor use only.

Package Contents

Please check that all parts and accessories are present and undamaged before proceeding with installation.

  • Pendant Light Fixture (Model PL230, also referred to as PLX005/PLX006)
  • Mounting Hardware (screws, rubber plugs, connector)
  • Instruction Manual (this document)

Installation Instructions

Models PLX005 and PLX006 are installed using the same method.

Installation Requirements:

  • Check the parts and accessories of the lamps.
  • Cut off the power supply or close the main breaker before installation.
  • Do not place lamps in flammable and humid places.

Installation Procedure:

  1. Confirm the position of the pendant and determine the location where holes need to be drilled.
  2. Drill holes in the marked area.
  3. After drilling is completed, push the rubber plug into the hole and tap it with a hammer if necessary.
  4. Use a screwdriver to fix the pendant on the wall.
  5. Connect the live wire, ground wire, and neutral wire to the connector.
  6. Cut off the power and connect the cables.
  7. Tighten the screws and fix the lamp on the wall.
Detailed diagram showing 7 steps for installing the pendant light, including drilling, wiring, and mounting.
Figure 1: Installation Diagram for Pendant Light

Operating Instructions

The CETANT LED Pendant Light features a simple operation.

  • Power On/Off: The light is controlled by a Touch On/Off Switch. Simply touch the designated area on the fixture or use your wall switch to turn the light on or off.
  • Light Color (if applicable): If your model is the "Tricolor light" variant, the touch switch may cycle through different color temperatures (e.g., warm white, neutral white, cool white) with successive touches. If it's a "Warm white" variant, it will provide a single warm white light. This fixture is not dimmable.

Care and Maintenance

To ensure the longevity and appearance of your pendant light, follow these simple maintenance guidelines:

  • Cleaning: Disconnect power before cleaning. Use a soft, dry cloth to wipe the fixture. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
  • Bulb Replacement: This fixture uses integrated LED bulbs and does not require bulb replacement. If the LED light source fails, please contact customer support.
  • Inspection: Periodically check for any loose connections or damaged wiring. If any issues are found, disconnect power immediately and consult a qualified electrician.

Troubleshooting

If you encounter any issues with your pendant light, please refer to the following common problems and solutions:

Problem Possible Cause Solution
Light does not turn on. No power supply; Loose wiring; Faulty switch. Check circuit breaker. Ensure all wires are securely connected. Test the switch.
Light flickers. Loose connection; Incompatible switch (though this model is not dimmable, ensure it's not connected to a dimmer). Verify all electrical connections are tight. Ensure the light is connected to a standard on/off switch.
Light color is not as expected. Incorrect model variant purchased; Tricolor light not cycled. Confirm the purchased model's emitting color. If "Tricolor light", try cycling the power switch to change modes.

If the problem persists after trying these solutions, please contact customer support.

Specifications

Feature Detail
Brand Name CETANT
Model Number PL230 (also referred to as PLX005/PLX006)
Item Type Pendant Lights
Installation Method Cord Pendant, self-contained
Material IRON (Finish), Acryl (Material), Aluminum/Silica Gel (Specific models)
Finish Painted
Light Source LED bulbs (integrated)
Is Bulbs Included Yes
Working Power 16W-18W (depending on model)
Luminous Flux 249-2000 lumens
Operating Voltage 85V-265V (AC) / 90-260V
Is Dimmable No
Switch Type Touch On/Off Switch
Lighting Area 5-10 square meters (3-8m² for specific models)
Number of Light Sources > 20
Certification CCC, CE, PSE, ROHS
Dimensions (approx.) Length: 40cm, Width: 9cm. Messenger wire: 2m (adjustable).
Diagram showing dimensions of two pendant lights, one gold and one black. Each is 40cm long, 9cm wide, with a 2m adjustable messenger wire.
Figure 2: Product Dimensions (Gold and Black variants)
Diagram for 'A-Black-1 Head' model, showing dimensions L9cm*H40cm, material Aluminum/Silica Gel, LED 16W, 90-260V, lighting area 3-8m², and 2m adjustable suspension line.
Figure 3: Specific Model Dimensions and Specifications (A-Black-1 Head)

User Tips

  • The lamp requires a direct electrical connection and does not operate on battery power or charging.
  • Users have noted satisfaction with the material quality and aesthetic appearance, stating the lamp looks beautiful and matches product images.
  • When selecting a color, be aware that "gold" finishes may sometimes appear more yellow depending on lighting conditions.

Warranty and Support

This product comes with a 2-year warranty from the date of purchase, covering manufacturing defects and material flaws under normal use.

For technical support, warranty claims, or any questions regarding your CETANT LED Pendant Light, please contact the seller or refer to the official product documentation.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.