HM Digital DM-1 DM-2

Contents

HM Digital Dual Water Quality Tester User Manual

Models: DM-1 Dual TDS Meter & DM-2 Dual EC Meter

Brand: JUANJUAN / HM Digital

1. Introduction

This manual provides instructions for the HM Digital DM-1 Dual TDS Meter and DM-2 Dual EC Meter. These devices are designed to measure the Total Dissolved Solids (TDS) or Electrical Conductivity (EC) levels in water, respectively. They are ideal for monitoring the effectiveness of water purification systems, such as Reverse Osmosis (RO) systems, and for general water quality assessment in various applications including aquariums and pools.

The DM-1 (TDS Meter) measures the total amount of inorganic elements (minerals, salts, metals) dissolved in water, expressed in parts per million (ppm). The DM-2 (EC Meter) measures the electrical conductivity of water in microsiemens (µS).

A lower TDS level is generally preferred for drinking water. The U.S. EPA's Secondary Regulations for drinking water advise a maximum contamination level of 500 ppm for TDS.

For additional information, you may refer to the official user manual PDF: HM Digital DM-1 User Manual (PDF).

2. Specifications

Below are the key specifications for the DM-1 Dual TDS Meter and DM-2 Dual EC Meter:

Feature DM-1 (TDS Meter) DM-2 (EC Meter)
Measuring Range 0.00-9990PPM (automatic *10 above 999PPM) 0-9990 µS
Resolution 1PPM (0-999PPM); 10PPM (1000-9990PPM) 0-999: 1 µS
Accuracy ±2% ±2%
Conversion Factor NaCl (avg. of 0.5) N/A
Factory Calibration 342 ppm NaCl (digital calibration) N/A
Sensor Cable Length Approx. 63 cm (24.5") Approx. 117 cm (1200mm)
Power Supply 2 x 1.5V button batteries (model 357A) 2 x AAA batteries (not included)
Auto Shut-Off After 10 minutes Automatic shut-off
Dimensions (L*W*H) 76mm x 47mm x 20mm (3.0 x 1.9 x 0.8 in) 116mm x 68mm x 18mm
Weight 79.4 g (2.8 oz) 250 g
Rear Installation With Velcro With hanging plate
Tee Joints 2 2
Display Type Digital LCD Digital LCD
Is Smart Device No No
With Backlight No No
Battery Included Yes (button battery) No (requires 2*AAA)
High-concerned chemical None None
Certification CE CE
Origin Mainland China Mainland China

Note: DM-1 is a TDS Meter, DM-2 is an EC Meter. Ensure you select the correct model for your needs.

3. Setup and Installation

The DM-1/DM-2 can be configured for various water purification or filtration systems. Typically, the 'IN' line connects to the source (tap) water, and the 'OUT' line connects to the product (filtered) water.

3.1 Components Overview

DM1 Dual TDS Meter with probes and 3-way connectors
Figure 3.1: DM1 Dual TDS Meter with probes and 3-way connectors.
DM2 Dual EC Meter with probes and 3-way connectors
Figure 3.2: DM2 Dual EC Meter with probes and 3-way connectors.
DM1 Product Introduction diagram with labeled components
Figure 3.3: DM1 Product Introduction diagram showing Tee joint, probe, water inlet/outlet detection port, line length, on-off key, display screen, and inlet/outlet control key.
DM2 Product Introduction diagram with labeled components
Figure 3.4: DM2 Product Introduction diagram showing Power button, Liquid crystal display, Pilot lamp, Inlet/outlet adjustment button, Back hanging wall design, and Line length.

3.2 Installation Steps (DM-1 & DM-2)

  1. Insert the white sensors fully into the bottom of the T-fittings.
  2. Orient the sensor pins so that they are perpendicular to the direction of the water flow. The water should flow over both pins equally. You should be able to see both pins if you look through the fitting.
  3. Disconnect the water source to prevent leaks during installation.
  4. Snip the source (tap) water tube at a point between the source and the filter. Insert both ends of the tube into the top of the IN line sensor's T-fitting.
  5. Snip the product (filtered) water tube at a point between the filter and a dispenser. Insert both ends of the tube into the top of the OUT line sensor's T-fitting.
  6. The monitor can be attached anywhere on or near the water system. DM-1 uses Velcro tape for mounting, while DM-2 features a back hanging wall design for fixed installation.
  7. Reconnect the water source. Your monitor is now ready for use.

NOTE: Consult a professional plumber for specific bracket or connection questions if you are unsure about the installation process.

3.3 Visual Installation Guide

Video: Unboxing, setup, and testing demonstration for the water quality monitor.
DM1 back view with Velcro for installation
Figure 3.5: DM1 back view showing Velcro for easy mounting.
DM2 back view with wall-mounted design
Figure 3.6: DM2 back view showing the wall-mounted design.

4. Operating Instructions

4.1 Taking Readings

  1. Press the "ON/OFF" button to power on the unit.
  2. To display the TDS/EC level of the feed (tap) water, slide the switch to the "IN" button.
  3. To display the TDS/EC level of the product (filtered) water, slide the switch to the "OUT" button.
  4. The displayed reading will be most accurate after approximately 10 seconds.
  5. For DM-1 (TDS Meter): If the "x10" icon appears on the display, the TDS level is above 999 ppm. Multiply the displayed reading by 10 to get the actual TDS level (e.g., 143 with 'x10' means 1430 ppm). If the 'x10' icon does not appear, the reading is the actual TDS level.
  6. To turn off the unit, press the "ON/OFF" button. The unit will automatically shut off after 10 minutes to conserve battery power.

4.2 Calibration (DM-1 TDS Meter)

Your DM-1 monitor is factory calibrated to 342 ppm (NaCl) and is ready for use. However, re-calibration may be necessary over time or for specific needs. The DM-2 (EC Meter) typically does not require user calibration.

  1. Connect the water tubes to the T-fitting. Ensure the water tubes connected to the fitting are 'IN' water (before the RO filter) and not 'OUT' water (product water).
  2. When calibrating, the TDS of the water you are using for calibration must be over 10 ppm. Insert the sensor you wish to calibrate into the T-fitting, ensuring correct orientation.
  3. Allow water to flow through the tubes to enable the sensor to measure.
  4. Measure the TDS of the flowing water using a separate, handheld TDS meter. Note this value as your target TDS for calibration.
  5. Turn on the monitor.
  6. Slide the switch to either "IN" or "OUT" depending on which sensor is in the calibration solution. The sensor must be inserted in the T-fitting for accurate results.
  7. Adjust the reading up or down by gently turning the calibration screw on the rear of the unit clockwise or counterclockwise until it matches your target TDS value.
  8. Separate calibration is not required for IN and OUT sensors.
DM1 Product display with packaging and instructions
Figure 4.1: DM1 Product display showing the device, probes, tee joints, and user guide.
DM2 Product display with packaging and instructions
Figure 4.2: DM2 Product display showing the device, probes, tee joints, and user guide.

5. Care and Maintenance

  • Avoid touching the sensor pins directly, as skin oils can adversely affect TDS/EC measurements.
  • To clean the sensor pins, use rubbing alcohol and allow them to air dry completely.
  • Do not remove the fittings from the sensors frequently, as this can strip the plastic and potentially cause leaks.
  • If you observe inaccurate readings or a faded display, replace the batteries or re-calibrate the monitor.

5.1 Changing the Batteries

If the display fades, the monitor does not power on, or the readings are incorrect, you may need to change the batteries:

  1. To replace the batteries, unscrew the three metal screws (not the orange plastic screw) on the rear of the unit and carefully remove the back panel.
  2. Remove the old batteries.
  3. Replace with fresh batteries, ensuring correct polarity. DM-1 uses two 1.5V button batteries (model 357A). DM-2 uses two AAA batteries.
  4. Close the back panel and replace the screws. Recalibration is generally not needed after battery replacement.

6. Troubleshooting

Issue Potential Solution(s)
Err display (error)
  • The water is out of the monitor's TDS/EC range.
  • The sensor cable is unplugged. Open the back panel and connect the cable securely.
Incorrect readings
  • Re-calibrate the monitor (DM-1 only).
  • Change the batteries.
Faded display
  • Change the batteries.
The "OUT" reading is higher than the "IN" reading
  • Check your connections. The sensors may have been reversed.

7. User Tips

  • Understanding Readings: For drinking water and filter performance, a lower TDS/EC level is generally better. There isn't a single "right" or "wrong" number; optimal levels depend on your specific system and application.
  • Fluctuating Readings: Slight fluctuations in TDS/EC levels from day-to-day are normal due to various environmental factors.
  • No Alarms: The DM-1 and DM-2 models do not feature alarms or programmable set points. You must manually check the readings.
  • Water Softeners: These meters are not suitable for monitoring water softeners, as softeners do not remove TDS.
  • Professional Advice: For complex installations or specific water quality concerns, consult a professional plumber or water treatment specialist.

8. Warranty and Support

8.1 Product Warranty

This product is warranted to the purchaser against material and workmanship for one (1) year from the date of purchase.

What is covered: Repair, parts, and labor, or replacement at the Company's option. Transportation charges for repaired or new product to be returned to the purchaser.

What is not covered: Transportation charges for the defective product to be sent to the Company. Any consequential damages, incidental damages, or incidental expenses, including damages to property. This includes damages from abuse or improper maintenance such as tampering, wear and tear, water damage, or any other physical damage. This product is not waterproof and should not be fully submerged in water. Products with any evidence of such damage will not be repaired nor replaced.

Implied Warranties: Any implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to five years from the date of purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. To the extent any provision of this warranty is prohibited by federal and state law and cannot be preempted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

NOTE: Warranties are product-specific. Third-party products and products deemed by HM Digital as "accessories" are not covered under warranty. Third-party products include, but are not limited to, batteries, fittings, and adhesives.

8.2 Obtaining Warranty Service

To obtain warranty service, please contact 800.383.2777 or email Warranty@HMDigital.com to receive further instructions. Before sending the product back, please include the following information:

  • Your name
  • Description of problem
  • Phone number/Address
  • Proof of purchase, including the date

If a returned product does not include the above-mentioned items, the Company reserves the right to refuse warranty service.

8.3 General Support

For more information on TDS, visit HMDigital.com/what-is-tds.

For product-specific information on the DM-1, visit HMDigital.com/product/dm-1.

You can also contact HM Digital at info@HMDigital.com.

Designed in USA and Korea. Made in China. An ISO-9001 Certified Company.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.