TCYATO LED T10 Strobe Lights Car Lamp User Manual

1. Introduction

Thank you for choosing TCYATO LED T10 Strobe Lights. These bulbs are designed to enhance your vehicle's visibility and aesthetics with their bright, multi-color, and stroboscopic capabilities. This manual provides detailed instructions for safe installation, operation, and maintenance to ensure optimal performance and longevity of your LED bulbs.

2. Safety Information

Always observe the following safety precautions during installation and operation:

• Power-Off Operation: Ensure the vehicle is completely turned off and the key is removed (for electric vehicles, disconnect the power supply) before beginning any installation.
• Vehicle Stability: Pull the handbrake to ensure the vehicle is stationary.
• Cooling Down: Allow the engine and existing lamp covers to cool down before operating to prevent burns.
• Electrical Compatibility: These bulbs are designed for 12V systems. Do not use with 24V large trucks and buses without verifying compatibility, as this can cause damage.
• Handling: Do not touch the glass part of the bulb directly with bare hands, as grease can cause overheating and burn out. Use a clean cotton cloth or gloves.
• Installation Space: Pay attention to the product's dimensions and the available installation space. Be careful not to press or squeeze the LED chips to avoid damage.

3. Product Overview

The TCYATO LED T10 Strobe Lights are high-quality bulbs featuring advanced design for durability and performance.

Key Features:

• Silicone All-Round Protection: Lamp beads are encased in a silicone shell for enhanced protection and extended service life.
• Energy Saving: Achieves high luminous intensity with fewer lamp beads, optimizing energy efficiency.
• Stable Chip Pins: Ensures more stable contact for longer-lasting light.
• Solid Chip Metal Welding: Provides a robust construction for prolonged use.
• Multi-Color & Strobe Functionality: Available in various colors and features stroboscopic effects for dynamic lighting.

4. Specifications

5. Installation

The core principle for installing width indicator lights (also known as "small lights") involves power-off operation, alignment with the vehicle model, correct reinstallation, and power-on testing. The following are general installation instructions applicable to most household cars.

5.1. Preparation

Tools and Materials:

• Appropriate model width indicator light bulbs (common models: T10/W5W)
• Flat-head / Phillips screwdriver
• Clean cotton cloth or gloves (critical)
• (Optional) Needle-nose pliers, alcohol cotton swabs

Safety Prerequisite:

• Ensure the vehicle is completely turned off and the key is removed (electric vehicles must disconnect power supply).
• Pull the handbrake to ensure the vehicle is stationary.
• Allow the engine and lamp cover to cool down before operating (to prevent burns).

5.2. Standard Installation Steps (Engine Compartment Replacement Example)

1. Open the Hood, Locate the Width Indicator Light:

   The hood switch is usually on the left foot side of the driver's seat. Pull the unlock lever and lift the hood up, then stabilize it from the front of the vehicle. The width indicator light is generally located inside the headlight assembly (the small lights beside the headlights). Find the black rubber dust cover at the rear of the headlight (diameter approximately 6-10cm).

2. Remove the Dust Cover and Old Lamp Holder:

   Turn the rubber dust cover counter-clockwise or gently pry it open. Store it properly to prevent dust and water ingress. Insert your hand inside and follow the wires to reach the plastic lamp holder (it has a flat handle shape). Pinch the lamp holder, turn it counterclockwise by about 90° to unlock, then gently pull out the entire lamp holder.

3. Replace the Bulb (Core):
   • Remove the old bulb: Directly pull it out (plug-in type) or rotate it out (clip type).
   • Install the new bulb: Do not touch the glass part directly (use a clean cloth/glove). Insert the bulb firmly into the lamp holder slot. For LED bulbs, pay attention to the positive and negative poles: if it does not light up, remove it, rotate 180°, and reinsert.
4. Reset and Seal:

   Insert the lamp holder with the installed bulb back into the lamp cover, turn it clockwise 90° to lock. Replace the rubber dust cover and ensure a complete seal (waterproof, dustproof). Replace any removed covers or screws in the opposite order.

5. Power-on Testing:

   Start the vehicle, turn on the first gear (width indicator light gear). Check if the front and rear width indicator lights are properly illuminated, without flickering, and without alarms.

5.3. Special Cases (for some models)

• Wheel Arch Access: For some models, it may be necessary to remove the inner lining of the wheel arch. Turn the steering wheel to the full lock position to expose the inner side cover. Remove plastic clips/screws and take off the cover. Reach in from the side to replace the width indicator light, following the same steps as above.
• LED Decoding: For some models, replacing with LED bulbs requires a decoding function bulb (Canbus compatible) to prevent error messages. If the bulb does not light up after installation, reverse the positive and negative poles first. If it still doesn't light up or an error occurs, it may require a decoding function bulb.

5.4. General Installation Notes

• The diameter of these bulbs is similar to traditional bulbs, allowing for direct replacement without circuit modification.
• These bulbs are not suitable for 24V large trucks and buses. Please verify your vehicle's voltage before installation.

6. Operation

Once installed, the TCYATO LED T10 Strobe Lights operate as your vehicle's width indicator lights. For models equipped with multi-color and strobe features, a remote control is typically included to manage these functions.

Remote Control Functions (if applicable):

If your bulbs come with a remote control, it allows you to:

• Turn the lights ON/OFF.
• Change the color of the LED illumination.
• Activate various strobe or flashing modes.

Refer to the remote control's specific buttons for detailed function mapping (e.g., 'R' for Red, 'G' for Green, 'B' for Blue, 'FLASH' for flash mode, 'STROBE' for strobe mode, 'ON/OFF').

7. Maintenance

TCYATO LED T10 Strobe Lights are designed for long-lasting performance with minimal maintenance. Follow these guidelines to ensure their durability:

• Cleaning: If necessary, gently wipe the exterior of the bulb with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
• Inspection: Periodically check the bulbs for any signs of damage or loose connections.
• Proper Sealing: Ensure that the rubber dust covers and any other seals around the headlight assembly are properly in place after installation to prevent moisture and dust ingress.

8. Troubleshooting

If you encounter issues with your LED T10 Strobe Lights, refer to the following common troubleshooting steps:

• Bulb Not Lighting Up:
  1. Remove the bulb and rotate it 180 degrees, then reinsert. LED bulbs are polarity sensitive.
  2. If still not lighting up, check your vehicle's electrical system for power to the socket.
• Error Message on Dashboard (Canbus Issue):

  Some vehicles, especially newer models, have a Canbus system that detects bulb outages. If an error message appears, your vehicle may require a Canbus-compatible decoding function bulb. Ensure you have purchased the correct type for your vehicle.

• Flickering or Intermittent Operation:

  Check for loose connections at the bulb socket. Ensure the bulb is fully seated. If the issue persists, it might indicate a voltage fluctuation or a need for a Canbus decoder.

9. User Tips

• Fitment Check: These bulbs can be quite long. Before purchasing or installing, verify that the bulb length will fit within your vehicle's lamp housing.
• Strobe Patterns: Some models may have specific strobe patterns, such as flashing 3 times and then stopping. Familiarize yourself with your bulb's specific modes.
• Versatile Use: While primarily designed as clearance lights, these bulbs can also be practical and functional for decorative purposes or other low-power indicator applications.
• Connector Length: Be aware that the connector might be a bit short for some applications, which could require careful handling during installation.

10. Warranty & Support

For warranty information, technical support, or any questions not covered in this manual, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.