User Manual: 18W Amber LED Work Light Spotlights

1. Product Information

This manual provides instructions for the installation, operation, and maintenance of your 18W Amber LED Work Light Spotlights. Designed for durability and performance, these lights are suitable for a variety of vehicles and applications.

Figure 1: Front view of the 18W Amber LED Work Light

2. Safety & Warnings

• Power Disconnection: Always ensure the power supply is disconnected before performing any operation, installation, or maintenance on the light fixture.
• Secure Fixing: When fixing the light fixture, it is strictly forbidden to use temporary or unreliable methods such as wooden wedges, nylon plugs, or plastic plugs. Reliable methods, such as expansion bolts, must be used to ensure stability and safety.
• Professional Installation: Do not attempt to install this product yourself unless you are qualified. Professional installation is highly recommended to ensure correct wiring and secure mounting.
• Avoid Hazards: When drilling, be extremely careful to avoid pre-buried electrical wires and water pipes in walls or ceilings.

3. Installation Instructions

Professional installation is recommended. The following instructions are for reference only.

General Installation Considerations:

• Installation Position: These amber LED fog lights can be installed in various positions:
• Roof Position: Can be used as a high beam (spotlight) or low beam (floodlight).
• Front Bar Position: Ideal for illuminating the road in foggy and rainy conditions.
• Middle Grid Position: Suitable for common vehicle models.
• Wiring: The lights feature a simple two-wire connection (red for positive, black for negative). Ensure proper polarity during connection.

Figure 2: Detail of light housing, internal structure, and wiring

Installation Methods:

There are four main types of installation for these work lights:

1. Magnetic Installation:

   This method offers flexibility and is commonly used in machine tool and vehicle repair applications.

   Operation: Simply attach the light with its strong magnetic base to a clean, flat metal surface.

   Key Points:

   • Surface Cleaning: Before attachment, ensure the metal surface is clean of oil and debris to avoid affecting magnetism and preventing scratches.
   • Confirm Secureness: After attachment, gently pull to confirm it is firmly attached. This is especially important when installed vertically or upside down; ensure the magnetism is strong enough to support the weight of the light fixture.
   • Wiring: Organize the power cord along the edge of the machine or vehicle to prevent it from getting tangled or crushed by moving parts.
2. Clamp Installation:

   Suitable for temporary mounting on desktops, shelves, or railings, saving space. This method typically involves using a separate clamping accessory (not included with the light itself).

   Operation: Rotate the knob at the back of the clamp to open it to the appropriate width, secure it to the edge of the object, and then tighten the knob.

   Key Points:

   • Check Clamping Force: After fixing, gently pull the light fixture to confirm it does not wobble or slip.
   • Protect Surfaces: If fixing to wooden or painted furniture, place a soft cloth under the clamp to prevent scratching the surface.
   • Note Thickness: Before purchasing a clamp, confirm that its maximum opening size is suitable for your intended installation location.
3. Screw Fixing (Wall-mounted/Ceiling-mounted):

   Suitable for scenarios requiring permanent fixing, such as walls or ceilings in workshops or warehouses. This method uses the included mounting bracket and hardware.

   

   Figure 3: Work light with mounting bracket and hardware

   Operation:

   • Drilling Holes: Place the bracket in the predetermined position and mark the screw hole positions with a pencil.
   • Installing the Bracket: Drill holes with an electric drill, insert expansion screws (if needed for your surface), and then securely fix the bracket to the wall or ceiling with screws.
   • Installing the Light Body: Install the light body of the work light onto the bracket, or connect and fix the light body to the base according to the specific instructions for your bracket type.

   Key Points:

   • Ensure Weight-bearing Capacity: Make sure the ceiling or wall structure can adequately support the weight of the light fixture.
   • Avoid Hazards: Avoid drilling into pre-buried electrical wires and water pipes.
4. Platform Placement:

   The simplest method, suitable for desktop work lights with a flat base.

   Operation: Simply place the work light stably on a flat surface such as a desktop or workbench.

   Key Points:

   • Stable Placement: Ensure the anti-slip pad on the base (if present) is in full contact with the desktop to prevent it from tipping over.
   • Cable Management: Organize the power cord to prevent it from being pressed by a chair or becoming a tripping hazard.

4. Operating Instructions

Once properly installed and wired to a 10-30V DC power source, operating the work light is straightforward:

• Power On/Off: Use the connected switch (not included) to turn the light on or off.
• Beam Type: The light provides an amber flood beam, designed for wide illumination.

5. Maintenance

To ensure optimal performance and longevity of your LED work lights, follow these simple maintenance guidelines:

• Cleaning: Periodically clean the lens and housing with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the materials.
• Inspection: Regularly check the wiring for any signs of wear, fraying, or damage. Ensure all mounting hardware remains tight and secure.
• Waterproof Seal: While rated IP67, avoid directing high-pressure water jets directly at the light for extended periods, especially around cable entry points.

6. Troubleshooting

If you encounter issues with your work light, refer to the following common problems and solutions:

• Light Does Not Turn On:
  • Check the power connection to ensure it is secure and correctly wired (red to positive, black to negative).
  • Verify that the power source (10-30V DC) is active and providing the correct voltage.
  • Inspect the fuse or circuit breaker in your vehicle's electrical system.
  • Ensure the switch controlling the light is functioning correctly.
• Light Flickers or is Dim:
  • Check for loose connections in the wiring.
  • Ensure the voltage supplied is within the 10-30V DC range and stable.
  • Inspect for any corrosion on terminals.
• Water Inside the Lens:
  • While IP67 rated, extreme conditions or improper installation can sometimes compromise the seal. Check for any visible cracks or damage to the housing or lens.
  • Ensure the cable entry point is properly sealed.

If problems persist after attempting these troubleshooting steps, please contact customer support.

7. Specifications

Figure 4: Back view with heat sink and cable

8. User Tips

• Check Dimensions: Before purchasing or installing, it is advisable to confirm the exact dimensions of the light to ensure it fits your intended mounting location.
• Consider Application: For off-road use, consider the mounting location carefully to maximize visibility and minimize obstruction.
• Wiring Harness: For easier installation and protection, consider using a dedicated wiring harness with a switch and fuse (not included).

9. Warranty & Support

This product comes with a 12-month warranty from the date of purchase, covering manufacturing defects. For any quality problems within 7 days of receipt, returns may be accepted.

Manufacturer Information:

Guangzhou Kuxiong Shi Trading Co., Ltd
No. 503, Building 3, Courtyard 2, Zhongquantang Road, Industrial Avenue, Haizhu District, Guangzhou City
Phone: 86-18814180059
Email: tingting26181@outlook.com

EU Authorized Representative:

Sea&Mew Consulting GmbH
Mittenhuber Straße 4, 92318 Neumarkt
Phone: +4915224685061
Email: Compliance.EU@outlook.com

For further assistance, please refer to the official user manual PDF available at: User Manual (PDF)