GGBEE PIR Motion Sensor Switch 1006A

Contents

GGBEE PIR Motion Sensor Switch

User Manual - Model 1006A

1. Introduction

Thank you for choosing the GGBEE PIR Motion Sensor Switch. This intelligent sensing switch is designed to automatically control lighting based on human movement, providing convenience and energy efficiency. It utilizes infrared human perception and offers intelligent adjustment capabilities to suit various environments.

Intelligent Sensing Switch Features
Figure 1: Intelligent Sensing Switch Features. Automatic light on when people come, off when they leave. Features include infrared human perception, microwave radar, and intelligent adjustment.

2. Safety Information

Please read and understand all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

  • Installation should only be performed by a qualified electrician or experienced person.
  • Always switch off the power at the main circuit breaker before performing any installation or maintenance.
  • Avoid installing the sensor on unstable or vibrating objects.
  • Ensure there are no obstructions or moving objects directly in front of the detection window that could interfere with accurate detection.
  • Do not install the sensor near areas with rapid air temperature changes, such as air conditioners or central heating vents, as this may cause false triggers.
  • For your safety, do not open the sensor cover if you encounter any issues after installation. Contact support if needed.

3. Package Contents

Please check the package for the following items:

  • 1 x GGBEE PIR Motion Sensor Switch Unit
  • 2 x Mounting Screws
  • 2 x Wall Plugs
PIR Motion Sensor Switch with Mounting Accessories
Figure 2: PIR Motion Sensor Switch with included mounting accessories.

4. Product Overview

The GGBEE PIR Motion Sensor Switch features a robust design and intuitive controls:

  • Adjustable Rotating Pulley: Allows flexible adjustment of the sensing angle to adapt to different environments.
  • Durable Shell: Constructed from carefully selected ABS material, which is flame retardant, durable, hard, and firm.
  • Intelligent Human Body Sensing Module: Automatically detects presence and controls the connected lighting.
Product Design Details
Figure 3: Product Design Details, highlighting the adjustable rotating pulley, ABS shell, and intelligent sensing module.

Control Knobs

The sensor features three adjustable knobs for fine-tuning its operation:

  • SENS (Sensitivity): Adjusts the detection range.
  • TIME (Time Delay): Sets how long the light stays on after motion is no longer detected.
  • LUX (Illuminance): Determines the ambient light level at which the sensor becomes active.
Control Knobs: SENS, TIME, LUX
Figure 4: Close-up of the SENS, TIME, and LUX control knobs.
Detailed Explanation of Control Knobs
Figure 5: Detailed explanation of the TIME, LUX, and SENS knob functions.

5. Installation and Setup

This manual primarily covers the 110-240V AC model. A 12V DC variant may have different wiring requirements; consult its specific diagram if applicable.

Pre-installation

  1. Ensure the power supply to the installation area is completely switched off at the circuit breaker.
  2. Choose a suitable mounting location, ideally between 1.8m and 2.5m from the ground, where the sensor has an unobstructed view of the detection area.

Mounting Steps

  1. Carefully unscrew the nail on the front cover and open the wire hole.
  2. Feed the power supply wires and load wires through the wire hole at the bottom of the sensor.
  3. Using the provided screws and wall plugs, securely fix the bottom part of the sensor to the chosen mounting position.

Wiring Connection

Connect the power and load wires to the connection-wire column as follows:

  • L (Brown wire): Connect to the Live (Phase) wire of your power supply.
  • N (Blue wire): Connect to the Neutral wire of your power supply.
  • OUT- (Red wire): Connect to the Negative terminal of your load (e.g., light fixture).
  • LOAD: Connect the Positive terminal of your load to the Live (Phase) wire of your power supply (or a separate switched live from the sensor if applicable to your model).
  • IN-: Connect to the Neutral wire of your power supply.

Note: The exact wiring configuration may vary slightly based on the specific model (AC vs. DC) and regional electrical standards. Always refer to the diagram printed on the device or in the specific product documentation if available.

Finalizing Installation

  1. Carefully reattach the front cover of the sensor and secure it with the screw.
  2. Restore power at the main circuit breaker. The sensor is now ready for testing.

6. Operation

Initial Test Procedure

  1. Turn the SENS knob fully clockwise (maximum sensitivity).
  2. Turn the TIME knob fully anti-clockwise (minimum delay).
  3. Turn the LUX knob fully clockwise (to the 'Sun' position, meaning it will operate in both day and night).
  4. Switch on the power. The connected load (light) should not turn on immediately.
  5. Allow approximately 30 seconds for the sensor to preheat.
  6. Walk into the detection area. The load should turn on.
  7. Move out of the detection area. After the minimum time delay, the load should turn off.
  8. Walk into the detection area again (wait 5-15 seconds after the light turns off). The load should turn on again.
  9. If no motion is detected, the load should remain off.

Adjusting Settings

  • Adjusting LUX (Illuminance):
    Turn the LUX knob anti-clockwise towards the 'Moon' symbol. The sensor will then only activate when the ambient light level falls below a certain threshold (e.g., only at night or in dark conditions). If set to the 'Sun' position, it will operate 24 hours a day regardless of ambient light.
  • Adjusting SENS (Sensitivity):
    Turn the SENS knob to adjust the detection distance. Higher sensitivity (clockwise) results in a farther detection range (up to 12m), suitable for larger rooms. Lower sensitivity (anti-clockwise) results in a closer detection range (down to 3m), suitable for smaller areas or to avoid unwanted triggers.
  • Adjusting TIME (Time Delay):
    Turn the TIME knob to set how long the light remains on after motion is no longer detected. The delay can be set from a minimum of 10 seconds (±3 seconds) to a maximum of 7 minutes (±2 minutes). If a second motion signal is received before the current delay period ends, the sensor will re-calculate the time delay from that moment.
Sensing Range and Distance Diagram
Figure 6: Automatic lighting response diagram, showing a sensing range of 120° and a sensing distance of 3-8m (adjustable).

7. Specifications

Model Number 1006A
Power Source 110-240V/AC (Also available in 12V DC variant)
Power Frequency 50Hz
Ambient Light 3-2000LUX (Adjustable)
Time-Delay Min: 10sec±3sec; Max: 7min±2min
Rated Load 800W (Incandescent lamp); 300W (Energy-saving lamp & LED)
Detection Distance 3-12m (<24°C) (Adjustable)
Detection Angle 120°
Working Temperature -20°C ~ +40°C
Working Humidity <93%RH
Installation Height 1.8m ~ 2.5m
Power Consumption 0.45W (work); 0.1W (static)
Detection Motion Speed 0.6-1.5m/s
Certification CE

8. Troubleshooting

If you encounter issues with your GGBEE PIR Motion Sensor Switch, please refer to the following common problems and solutions:

Problem: The connected load (light) does not work.

  • Solution 1: Check if the connection wiring of the power supply and load is correct and secure.
  • Solution 2: Verify that the load (e.g., light bulb) is functional.
  • Solution 3: Ensure the LUX setting corresponds to the ambient light conditions. If it's daytime and LUX is set to 'Moon', the sensor will not activate.

Problem: The sensitivity is poor (detection range is too short or inconsistent).

  • Solution 1: Check for any obstructions in front of the detection window that might block the signal.
  • Solution 2: The ambient temperature might be too high, reducing the sensor's effectiveness.
  • Solution 3: Ensure the motion source is within the specified detection field.
  • Solution 4: Verify that the installation height is within the recommended range (1.8m-2.5m).
  • Solution 5: Ensure the moving orientation is correct (movement across the sensor's field is generally more effective than directly towards it).

Problem: The sensor cannot shut off the load automatically (light stays on).

  • Solution 1: Check if there is a continual motion signal within the detection field.
  • Solution 2: Verify that the TIME delay is not set to its longest duration.
  • Solution 3: Ensure the power supply to the load corresponds to the instruction (e.g., not exceeding maximum wattage).
  • Solution 4: Check if the temperature near the sensor is changing significantly (e.g., from an air conditioner or central heating vent), which can cause false triggers.

9. Warranty and Support

GGBEE products are manufactured to high-quality standards. For any warranty claims or technical support, please refer to your purchase documentation or contact the seller directly. Please have your model number (1006A) and purchase date available when seeking support.

© 2024 GGBEE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.