1. Introduction
The Autel MaxiIM KM100 is a professional intelligent key tool designed for comprehensive key programming tasks. It integrates universal key generation, transponder reading/cloning, and IMMO learning functions into a compact and user-friendly device. Paired with the MaxiVCI V200 vehicle communication interface, the KM100X provides a complete solution for professional locksmiths and automotive technicians.
This manual provides detailed instructions for the safe and effective use of your Autel MaxiIM KM100 Key Fob Programming Tool. Please read it thoroughly before operation.
2. Safety Information
For your safety and to prevent damage to the device and vehicles, it is crucial to read and understand all safety instructions. Automotive servicing involves various procedures and tools; always ensure you are knowledgeable about the system being tested and use proper methods.
Safety Messages
- DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
- WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Safety Instructions
- Ensure the service area is well-ventilated when an engine is operating to avoid carbon monoxide poisoning.
- Do not turn the volume up too loud when using headphones to prevent hearing loss.
- Always perform automotive testing in a safe environment.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area.
- Put the transmission in PARK (automatic) or NEUTRAL (manual) and engage the parking brake.
- Place blocks in front of drive wheels and never leave the vehicle unattended while testing.
- Be cautious around ignition coils, distributor caps, ignition wires, and spark plugs due to hazardous voltages.
- Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep the test equipment dry, clean, and free from oil, water, and grease.
- Do not drive the vehicle and operate the test equipment simultaneously.
- Refer to the vehicle's service manual for diagnostic procedures.
- Ensure the vehicle battery is fully charged and the DLC connection is clean and secure.
- Do not place the test equipment on the distributor of the vehicle; strong electromagnetic interference can cause damage.
- Avoid strong electromagnetic environments.
3. Package Contents
The Autel MaxiIM KM100X kit typically includes the following components:
- MaxiIM KM100 Main Unit
- MaxiVCI V200 Vehicle Communication Interface
- USB Type-C Cable
- Power Adapter
- Two Universal Keys (Smart Keys)
- Hard Carrying Case

4. Device Overview
4.1 MaxiIM KM100 Main Unit
The KM100 is a handheld tablet with a 5.5-inch touchscreen, designed for intuitive operation.

Front/Back View Components:
- 5.5-inch Touchscreen: Main display for operation.
- Ambient Light Sensor: Detects ambient brightness for display adjustment.
- Status LED: Indicates device status.
- Low Frequency Detection Collector: Collects low frequency data.
- Transponder Slot: Reads and writes transponders.
- Vehicle Key Slot: Reads key information and measures remote frequency.
- Rear Camera: For image capture (8 megapixels).
- Camera Flash: For illumination.
Side/Bottom View Components:
- Power/Lock Button: Press and hold to turn on/off, tap to lock the screen.
- Type-C USB Port: For data transfer and charging (also an OTG port).
- SD Card Slot: For expandable storage.
- Mini USB Port: For specific connections.
- Microphone: For audio input.
4.2 MaxiVCI V200 Vehicle Communication Interface
The MaxiVCI V200 is the device that connects the KM100 to the vehicle's OBD-II port.
Components:
- Flashlight Button: Activates a built-in flashlight.
- Power LED: Indicates power status.
- Vehicle/Connection LED: Indicates vehicle communication status.
- Vehicle Data Connector (16-pin): Connects to the vehicle's OBD-II port.
- USB Port: For wired connection to the KM100.
VCI LED Description:
| LED | Color | Description |
|---|---|---|
| Power LED | Yellow | VCI powered on, performing self-check. |
| Green | VCI ready for use. | |
| Flashing Red | Firmware upgrading. | |
| Vehicle/Connection LED | Green | Solid Green: VCI connected via USB. Flashing Green: VCI communicating via USB. |
| Blue | Solid Blue: VCI connected via Bluetooth. Flashing Blue: VCI communicating via Bluetooth. |
5. Setup
5.1 Initial Power On/Off
To power on the KM100, press and hold the Power/Lock button on the right side of the tool until the screen lights up. The system will boot up and display the Job Menu.
To power off, press and hold the Power/Lock button, then tap 'Power off' on the screen, and confirm with 'OK'. The tool will shut down in a few seconds.
5.2 Battery Installation (Universal Key)
Before using the Autel universal key, ensure its battery is correctly installed:
- Place the key on a flat surface, front side down.
- Locate the small slot on the side of the key. Gently wedge a flathead screwdriver into the slot until the casing pops out.
- Carefully remove the casing.
- Place the correct battery with the positive side facing up.
- Place the casing back and gently squeeze until it seals.
5.3 Software Update
Regular software updates improve functionality, add new tests, models, and enhancements. The KM100 automatically searches for updates when connected to the internet.
- Ensure the tool is connected to a power source and has stable internet access.
- From the Job Menu, tap 'Update' or tap the update notification message.
- To update all items, tap the 'Update All' icon. To update specific items, tap 'Acquire' next to each item.
- Once downloaded, the software will install automatically.
5.4 Tool Registration
To receive software updates, your tool must be registered. Register directly on the tool or via the Autel website (pro.autel.com).
- Visit pro.autel.com.
- Sign in or create an Autel ID.
- Enter required personal information and verify your email.
- Set a password and accept terms.
- Enter your tool's serial number and password (found in Settings > About) on the Product Registration screen.
- Enter the CAPTCHA code and click 'Submit'.
5.5 VCI Connection (Bluetooth/USB)
The MaxiVCI V200 connects to the vehicle's OBD-II port and communicates with the KM100 via Bluetooth or USB.
To pair via Bluetooth:
- Power on the KM100.
- Insert the VCI into the vehicle's DLC.
- On the KM100, go to 'Settings' > 'VCI Manager'.
- Tap 'Scan' in the upper-right corner.
- Select the VCI device (e.g., 'Maxi' followed by serial number) from the list.
- Once paired, the connection status will show 'Paired', and the VCI's Connection LED will be solid blue.
6. Operating Instructions
The KM100 offers a range of key programming and immobilizer functions accessible via its Job Menu.

6.1 Universal Key Generation
This function programs Autel universal keys for your desired vehicle model.
- From the Job Menu, tap 'Universal Key'.
- Confirm vehicle information (region, make, model, year) manually or via AutoVIN (requires VCI connection).
- Ensure a battery is installed in the universal key.
- Place the universal key into the key slot of the KM100.
- Tap 'Generate Universal Key' and keep the key stable during generation.
6.2 Transponder Reading/Cloning
This function allows you to read, clone, and edit transponder information.
To Read a Transponder:
- From the Job Menu, tap 'Reading/Cloning'.
- Place the transponder into the transponder slot or the key into the key slot.
- Tap 'Read'. The Transponder Information screen will display chip type, IMMO type, transponder ID, locking status, and code mode.
To Clone a Transponder:
- After reading, choose a transponder ID from the cloning options.
- Place the original key into the key slot.
- Tap 'Start' to begin reading and cloning. Follow on-screen instructions and voice prompts.
6.3 Transponder Function
This section covers transponder generation, simulation, and frequency detection.
Transponder Generation:
Generate a transponder for different protocols or models using a blank transponder.
- From the Job Menu, tap 'Transponder Function'.
- Choose 'Vehicle Search' (select vehicle make) or 'Transponder Search' (enter transponder ID).
- Place the blank transponder into the transponder slot.
- Tap 'Generate Transponder'.
Transponder Simulation:
Simulate the KM100 as a transponder for emergency starts or other needs.
- From 'Transponder Function', select 'Transponder Simulation'.
- Choose a transponder ID (ID46, ID47, ID48, ID49, ID4A, ID8A).
- Enter parameters for each register.
- Tap 'Simulate'. Once successful, place the low frequency detection collector (top antenna) 0-5 cm above the inductive area to detect the simulated signal.
Frequency Detection:
Detects smart key frequencies for various vehicle models.
- From 'Transponder Function', select 'Frequency Detection'.
- Place your smart key near the key slot (within 10 cm).
- Press any button on your smart key to start detection. The frequency will be displayed in text and graph forms.
6.4 IMMO Functions
The IMMO application requires an OBDII connection to the vehicle to retrieve immobilizer information and perform functions like Key Learning, Remote Control Learning, and Remote Control Add.
Vehicle Identification:
The KM100 supports AutoVIN, Manual VIN Input, Automatic Selection, and Manual Selection for vehicle identification.
- From the Job Menu, tap 'IMMO'.
- Connect the VCI to the vehicle's DLC and turn on the ignition.
- Tap 'VIN Scan' and select 'AutoVIN' or 'Enter VIN Manually'.
- Confirm the vehicle profile.
Key Learning (Example):
- After vehicle identification, select 'Control Unit' > 'Immobilizer' and choose the IMMO system (e.g., Instrument Cluster).
- Tap 'Key Learning'. The tool will read IMMO data.
- Input the number of keys to be learned and tap 'OK'.
- Follow on-screen instructions to place the key in the inductive area and tap 'OK'.
- Once key learning is complete, tap 'OK' to exit.
6.5 Special Functions
The KM100 provides several practical special functions.
IMMO Data Processing:
Load IMMO-related ECU information to calculate passwords and other IMMO data, which can then be written to a transponder to create an extra key.
- From the Job Menu, tap 'Special Function' > 'IMMO Data Processing'.
- Choose region, vehicle make, and immobilization system.
- Browse and load the required IMMO data.
Key Unlocking:
Renew a used smart key to unlock a new car by renewing its firmware via cable connection.
- From 'Special Function', select 'Key Unlocking'.
- Choose vehicle make and correct key information.
- Follow on-screen instructions: remove battery, connect cables per diagram.
- Tap 'Unlock'.
Button Customization:
Assign button functions on the Autel universal key.
- From 'Special Function', select 'Button Customization'.
- Adjust the button values as needed.
- Tap 'Confirm Writing' to save changes to the key.
Ignition Coil Detection:
Gather data on IMMO protocol and transponder type of the vehicle.
- From 'Special Function', select 'Ignition Coil Detection'.
- Place the low frequency detection collector close (within 10 cm) to the ignition coil or emergency start coil.
- If a signal is detected, the detection result and transponder type will appear.
7. Maintenance
Proper maintenance ensures the longevity and optimal performance of your KM100.
- Cleaning: Use a soft cloth with alcohol or a mild window cleaner for the touchscreen. Do not use abrasive cleansers or automotive chemicals.
- Storage: Store the device in dry conditions within normal operating temperatures. Avoid humid, dusty, or dirty areas.
- Handling: Keep hands dry when using the touchscreen. Check housing, wiring, and connectors for dirt and damage before and after use. Do not attempt to disassemble the tool or VCI. Avoid dropping the device or placing heavy objects on it.
- Battery Care: Use only authorized battery chargers and accessories. Ensure the charger does not contact conductive objects. Avoid operating the tool near devices that might cause signal interference (e.g., microwaves, cordless phones).
8. Troubleshooting
If you encounter issues with your KM100, refer to the following common problems and solutions:
8.1 Tool Not Working Properly
- Ensure the tool is registered online.
- Verify system software and diagnostic applications are updated.
- Check internet connection.
- Inspect all cables, connections, and indicators for proper signal reception.
8.2 Short Battery Life
- This may occur in areas with low signal strength.
- Turn off the device when not in use.
8.3 Unable to Power On
- Ensure the tool is connected to a power source or has sufficient battery charge.
8.4 Unable to Charge
- Check if the charger is faulty (try another charger).
- Ensure the device is within normal operating temperatures (not too hot/cold).
- Verify the charger is properly connected to the device.
If problems persist, contact Autel's technical support.
9. Specifications
9.1 MaxiIM KM100 Main Unit
| Item | Description |
|---|---|
| Display | 5.5-inch touchscreen with 1280 x 720P resolution |
| Operating System | Android™ 9.0 |
| Processor | Rockchip PX30 4 x ARM Cortex-A35 (1.5 GHz) |
| Memory | 2 GB RAM + 64 GB Flash |
| Connectivity | Wi-Fi, Bluetooth, USB 2.0 Type-C |
| Sensor | Ambient light sensor |
| Audio Output | Beep |
| Internal Battery | 3.85 V/4950 mAh lithium-polymer battery |
| Power Input | 5 V/2 A |
| Operating Temp. | 0 to 50 °C (32 to 122 °F) |
| Storage Temp. | -10 to 60 °C (14 to 140 °F) |
| Dimensions (L x W x H) | 200mm x 89mm x 22mm |
| Weight | 352.7 g (0.78 lb.) |
9.2 MaxiVCI V200
| Item | Description |
|---|---|
| Communications | BLE + EDR, Type-C USB |
| Wireless Frequency | 2.4 GHz |
| Input Voltage Range | 8 V to 30 V DC |
| Supply Current | 150 mA @ 12 V DC |
| Operating Temp. | 0 to 50 °C (32 to 122 °F) |
| Storage Temp. | -20 to 60 °C (14 to 140 °F) |
| Dimensions (L x W x H) | 89.89mm x 46.78mm x 21mm |
| Weight | 70.7 g (0.156 lb.) |
| Built-in Battery | 3.7 V Lithium Battery |
| Light | White LED |
10. User Tips
- Ease of Use: Many users find the KM100 very easy to use, especially with its on-screen instructions and video tutorials. It's often described as a