HKIXDISTE JAXS-WCK-L17

Contents

HKIXDISTE Wireless NVR Recorder User Manual

Model: JAXS-WCK-L17

1. Introduction

This manual provides detailed instructions for setting up, operating, and maintaining your HKIXDISTE Wireless NVR Recorder. Please read this guide carefully before use to ensure proper functionality and safety.

Safety Precautions

  • Do not place any fluid containers on the product.
  • Use the product in a ventilated environment and prevent blocking the vents.
  • Use only the included power supply with the product to prevent damage.
  • Operate the product within its standard working temperature and humidity.
  • Clean dust from the PCB regularly to prevent short circuits and ensure proper product operation.
  • Comply with local regulations and policies during the installation of this NVR.

2. Product Overview

2.1 NVR Components

HKIXDISTE Wireless NVR Recorder with two antennas
Figure 1: HKIXDISTE Wireless NVR Recorder (NVR) with 16CH, 5MP AHD DVR, Face Detection, Human Detection capabilities, and EseeCloud APP support.

The NVR unit features:

  • Wireless Antenna Ports: Double antennas for extended wireless range.
  • WAN Port: Connects your NVR to the Internet.
  • VGA Port: For viewing on a VGA monitor.
  • HDMI Port: For viewing on an HDTV.
  • USB Ports: For mouse and backup devices.
  • Power Input: For connecting the power adapter.

2.2 IPC (IP Camera) Components

The NVR can be combined with various cameras. The interface description below uses common cameras as an example. Please refer to your specific camera's actual interface positions.

Diagram showing IP Camera components and connections
Figure 2: IP Camera with IR illuminator, white light, human infrared sensor, speaker, microphone, antenna, USB charging port, and status lights.

IP Camera Status Light Indications:

  • Unbright: IPC system is not ready or abnormal.
  • Flash: IPC is in the code-matching status.
  • Long time bright: IPC and NVR have been coded, the connection status is normal.
  • Slow Flash: IPC is coded with NVR, but the connection is disconnected.
  • Note: In night vision mode, the indicator light turns off after 5 seconds to prevent light interference.

Button Operations (Two-button model):

  • Press and hold the on/off button for 2 seconds to shut down.
  • Press and hold the on/off button for 2 seconds to power on.
  • Press and hold the reset button for 3 seconds to reset.

3. Setup Guide

3.1 Hard Drive (HDD) Installation (Optional)

The NVR supports most 3.5" SATA HDDs or 2.5" SATA HDDs. If your kit includes a hard disk, follow these steps:

  1. Unscrew and remove the top cover of your NVR.
  2. Connect the SATA power and data cables from the NVR to the corresponding ports on your HDD.
  3. Gently turn the NVR and HDD over, aligning the holes.
  4. Use a Phillips screwdriver to secure the HDD with the provided screws.

Note: The HDD must be formatted before recording. For optimal wireless signal, it is recommended to place the NVR in an open, high position.

3.2 System Connection and Installation

This system is standalone with an embedded Linux Operating System. Just like a desktop PC, it needs a screen (TV or monitor with VGA or HDMI input) to access the OS.

  1. Install antennas for cameras and the NVR.
  2. Connect a screen to the NVR via its HDMI or VGA port (HDMI and VGA cables are not included).
  3. Plug the NVR into power using the 12V 2A power adapter.
  4. Plug cameras into power using the 12V 1A power adapters.
  5. Within seconds, camera images should appear on the screen.
  6. Plug the included mouse into a USB port on the back of the NVR to operate the system.
Wiring diagram for NVR and cameras
Figure 3: Easy Connection Diagram showing NVR connected to power, network, VGA/HDMI output to PC/TV, and cameras powered by adapters. P2P remote viewing is available via phone app.

Note: Wireless NVR cannot be connected to a wireless router wirelessly at present; it must be connected by network cable.

3.3 Initial Configuration on TV or Monitor

After powering on, please follow the steps of the setup wizard to complete the settings of language, network, time, view real-time screen, password, hard disk, and download the mobile app. If you see the prompt "Network status is good!" in the network setup wizard interface, it means your recorder has successfully connected to the Internet.

Tip: If there is no Internet near your video recorder device, you can also choose to use it without connecting to the Internet. This method will make it impossible to use the mobile APP to watch the video from a long distance.

Default ID: admin

Password: none (leave empty, just click login)

Tip: To protect your privacy, please set your password at the earliest convenience. Right-click the mouse > Go to System Setup > System Admin > User Management to set password.

4. Operating Instructions

4.1 Menu Navigation

Right-click anywhere on the screen to access the main menu. Right-click again to exit the menu or go back.

Menu Item Description
Split screenChange view state (multiple or single cameras).
PlaybackEnter the video playback interface to view recorded video.
CameraView settings related to the added camera.
System SetupManage all system settings.
Channel SortAdjust camera channel sorting order.
DiagnosticsDiagnose camera status, signal, and firmware version.
NetworkView device's network connection.
Log downExit the system, restart, or shutdown functions.

4.2 System Settings

From the System Settings menu, you can modify:

  • General settings: Set language, display resolution, audio volume, and view firmware information.
  • Camera settings: Configure all camera settings, alarm settings, and recording settings.
  • Date/Time: Set device time, date, and time zone information.
  • Network settings: Configure network connection to router, and wireless channel settings.
  • Device Diagnosis: Perform device and added camera status detection and diagnosis.
  • Storage settings: View hard disk information and format.

4.3 Channel Toolbar

Move the mouse button to the corresponding channel, and the toolbar at the bottom of the channel will be activated. Icons include: Full-screen playback button, Color adjustment button, Audio output switch button, Digital zoom button, PTZ control button, and Alarm button.

4.4 Recording Settings

Right-click the mouse > select camera settings > select recording mode on the right side of the interface. The NVR supports different recording modes:

  • Battery cameras: Best power saving, best video recording, and always video recording.
  • Constant power cameras: Constant recording, event recording.

Detailed mode functions are available in the settings interface for detailed viewing.

4.5 Video Playback

To play recorded video:

  1. Right-click on the video preview interface and select Playback. It will automatically retrieve and play the video of the day (default video playback).
  2. Select the video playback type (video playback or smart playback), select the date and channel, and select the recording type (movement, timing, humanoid). The recording will be retrieved in real time.

Function Introduction:

  • Play/Pause: Standard playback controls.
  • Fast forward: 2x, 4x, 8x speed options.
  • Switch between 1 and 4 channels.
  • Full screen: View video in full screen.
  • Timeline: Click 24h, 1h, 30m in the lower left corner to change the time axis unit. Click on the time axis to start playback from that point.
  • Smart playback: Click the video thumbnail, select human shape or mobile recording to view specific clips. (Note: SD card video recording does not support intelligent playback).
  • All recordings: View all recording clips for the current channel.
Image showing face detection and playback features
Figure 4: Face Detection & Face Playback feature, showing timestamps for detected faces.
Image showing motion detection alarm feature
Figure 5: Motion Detection Alarm, illustrating how the system detects movement and sends an alert to a mobile phone.

4.6 Video Backup

To backup videos using a USB flash drive:

  1. In the video playback interface, select the channel window to backup.
  2. Click the backup video button in the lower right corner.
  3. Insert a USB drive and select the export folder.
  4. Click export.

Reminder: USB drives must be FAT32/exFAT format. Video files are packaged hourly.

4.7 Add IP Camera (IPC)

1. Automatically add:

For wireless cameras shipped with the recorder, simply connect the power supply. The recorder will automatically add the camera, and you can view its screen in the preview interface.

2. Manually add:

  1. Click the '+' icon at the bottom of the preview interface.
  2. Reset the camera or connect it to the recorder with a network cable, then click Next.
  3. Once the camera to be added is found in the waiting list, click Next.
  4. After confirming the video screen, click Next to enter the preview interface.

Tip: When adding a camera, please try to place the camera and the recorder as close as possible.

4.8 Mobile App (EseeCloud)

Download and Install:

Search for "EseeCloud" in your app store or scan the QR code. Requires iOS 9.0 or above, or Android 5.1 or above.

Registration and Login:

  1. Click Register, input your mobile phone number or email, the verification code, and complete the registration.
  2. Enter your registered mobile phone number or email and password on the login interface, and click Login.

Add Device:

  1. On the device list interface, click to add a camera.
  2. Scan the ID QR code on the recorder (click the QR code icon in the lower right corner of the preview interface).
  3. Set the device name and add successfully.

Tip: Ensure your video recorder is connected to the Internet when using the EseeCloud APP to add and view the video recorder screen.

5. Expanding Wireless Coverage

Wireless connections are convenient, but wireless signal attenuation can occur due to obstacles. The following methods can bypass obstacles and extend the signal transmission distance:

  • Reasonably adjust antenna placement.
  • Use antenna extension cables.
  • Utilize auto repeater functionality.
  • Implement camera cascade.

Note: Repeaters and camera cascade extend signal distance, not strength. Proper placement is key. It's recommended to set up repeaters near the NVR before installing cameras.

5.1 Antenna Adjustment

Antenna gain is strongest around the antenna and weaker at the ends. For optimal image transmission:

  1. Place NVR and IPC antennas in high, open areas, and not near walls, metal, glass, and other obstacles, which will affect the signal's outward divergence.
  2. Position IPC antennas parallel to NVR antennas as much as possible so that the respective maximum radiation direction angles are opposite to form the maximum signal coverage.
Diagram showing wireless cascade technology
Figure 6: Latest Cascade Technology, illustrating how multiple cameras can extend the wireless range by relaying signals.

5.2 Using Antenna Extension Cord

If a camera shows a weak signal due to a wall, remove the original antenna, replace it with an extension cord, and drill a hole through the wall or bypass it to a stronger signal area.

5.3 Camera Repeater or Repeater Functionality

Auto repeater is the cascading between cameras and cameras, and wireless repeater is the cascading between cameras and repeaters. If the position between the camera and the camera cannot be cascaded in an actual scene, it is a good choice to place a sensor-less repeater between the video recorder and the camera. (The packaged product does not include a wireless repeater).

Repeater Setting Interface:

Right-click the mouse > Video management > Repeater settings. Enter the repeater settings interface. On this page, you can view the repeater and repeater topology diagrams, and set the repeater in the interface. NVR indicates the wireless NVR, CHK-Auto indicates cameras that support auto repeater, CHx indicates cameras that support manual repeater only, RPx-Auto indicates repeater that supports wireless repeater, and router indicates a repeater that only supports network relay. There is an "Auto repeater" switch in the upper right corner of the repeater setting interface; it is off by default and can be turned on by the user according to actual needs.

Wireless Repeater Use:

When the repeater and camera on the repeater setting interface display "CHx-Auto", the wireless repeater does not need to be set. If the camera CH is too far away to connect to the NVR, you only need to place a wireless repeater at a reasonable position between the camera and the recorder.

Note: To use a wireless repeater, the repeater must first be paired to the wireless NVR. Press and hold the wireless repeater for 10 seconds. When the NVR status light flashes quickly, it will automatically pair with the NVR without any sense when approaching the wireless NVR. After successful pairing, the NVR status light is always on.

Auto Repeater Use:

If "CHx-Auto" is displayed on all cameras in the repeater setting interface, enable the "Auto Repeater" switch and click "Apply". The system will automatically find cameras with nearby signals and select the optimal channel.

Manual Repeater Use:

If the auto repeater performance is not perfect, you can set the manual repeater yourself. All cameras and repeaters support manual repeater. Example: cascade IPCAM4 to IPCAM3.

  1. First, uncheck the "Auto Repeater" switch in the upper right corner of the repeater setting interface, and click the "Apply" button below to turn off the auto repeater.
  2. Click the signal icon behind channel CH4, select camera channel CH1, click Apply to make the settings effective, and then click the Refresh button to update the repeater relationship diagram.
  3. To delete a repeater, move the mouse over the CHx (where x is the channel number) to be deleted, left-click the mouse to delete, and then click the "Apply" button to confirm the deletion.

6. Specifications

Feature Specification
Brand NameHKIXDISTE
Model NumberJAXS-WCK-L17
Video Compression FormatH.265
Video Resolution5 MP
Video StandardNTSC, PAL
Video Output1VGA + 1HDMI-Compatible
Video Port10CH input/ 1CH VGA, 1CH HDMI output (for 10CH model) or 16CH input/ 1CH VGA, 1CH HDMI output (for 16CH model)
Audio Compression FormatG711A
Audio Input1 RCA
Audio Output1CH RCA
Audio Port1CH audio input, 1CH audio output
Technologyanalog, HDCVI, HDTVI, Network
e-Cloud(P2P)Yes
Network InterfaceRJ45 10/100M
Communication InterfaceRS485
Network ProtocolTCP/IP
Wireless SecurityWEP
IP ModeDynamic IP address
Hard Drive Size3.5''
Hard Drive Interface TypeSATA
Hard Drive Port1*SATA Port (support up to 8TB HDD)
Alarm ActionEmail Photo
Alarm SystemFace/Motion Detection + Email Alert
Face DetectionSupport
Face RecordSupport
Face PlaybackSupport
Supported Operating SystemsMicrosoft Windows ME, XP, Vista, 7, Mac OS
Supported Mobile SystemsiPhone OS, Android
Mobile Phone Viewing AppEseeCloud App
Remote ViewAndroid, iPhone, iPad, PC, VMS etc
ApplicationHome, store, shop, office, supermarket etc.
Power OptionalEU, US, UK, AU (Optional)
LanguageSupport multi-language (English, Russian, Spanish, etc.)
CertificationCE, FCC, RoHS
Country of OriginShenzhen, China
Comparison of H.264 and H.265 compression formats
Figure 7: Compression Format Comparison. H.265 offers 50% less storage and bandwidth usage compared to H.264, resulting in HD image quality and faster transmission speed.

7. Maintenance

7.1 General Maintenance

  • Regularly clean dust from the PCB to prevent short circuits and ensure proper product operation.
  • Ensure the product is used in a ventilated environment and that vents are not blocked.
  • Use only the power supply provided with the product.

7.2 Smart Detection Settings

Right-click the mouse > Camera settings > Smart detection settings. Here you can configure:

  • Detection area
  • Sensitivity level
  • Detection type (humanoid)
  • Humanoid frame switch

7.3 Smart Detection Period Setting

Right-click the mouse > Camera settings > Time period settings. Within the designated time frame, the device will perform detection recording. You can customize the recording schedule, including 24-hour smart detection and alarm, or specific time periods. When the recorder detects a hard drive, the default setting is to record 24/7 continuously.

8. Troubleshooting

8.1 Common Issues and Solutions

  • No image on screen: Check power connections for NVR and cameras. Ensure HDMI/VGA cables are securely connected to a monitor/TV.
  • Weak wireless signal:
    • Place NVR in an open, high area.
    • Adjust antenna direction (parallel for NVR and IPC).
    • Use antenna extension cords if walls are blocking signals.
    • Utilize repeater functionality (auto or manual) to extend range.
  • Cannot connect to EseeCloud App: Ensure NVR is connected to the internet via WAN port. Verify correct mobile number/email and password for login.
  • Hard drive not recording: Ensure HDD is properly installed and formatted. Check recording settings (24/7 or event-based).

8.2 FCC Radiation Norm Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Compliance Statement:

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs (e.g., to television reception), try the following:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a different circuit.
  • Consult the dealer or an experienced radio/TV technician.

CAUTION! Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

9. User Tips

  • Wireless Camera Scanning: The NVR box is designed to scan and connect to wireless cameras. If you have additional wireless cameras, the NVR should be able to detect and integrate them.
  • Compatibility: The system is designed to work with its own wireless cameras. While some users ask about compatibility with other IP or Onvif cameras, the primary design is for the integrated system. For best performance, use HKIXDISTE compatible cameras.
  • Password Security: Always set a strong password for your NVR immediately after initial setup to protect your privacy and system security.
  • Network Connection: For remote viewing via the EseeCloud app, ensure the NVR is connected to the internet via a network cable. Wireless connection to a router is not supported for the NVR itself.

10. Warranty and Support

This product comes with a 3-year warranty.

For further assistance or technical support, please refer to the official HKIXDISTE support channels or contact your retailer.

A user manual in PDF format is available for download. You can access it via the following link: User Manual (PDF)

11. Video Demonstration

Watch this video for a brief overview of the NVR system and its applications:

Video: NINI VISION CCTV Security Monitoring - Demonstrates various application scenarios for the NVR system, including home, shopping mall, gym, park, office, factory, street, and hotel environments.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.