POKESS 7M2AR21813MC, 7M2AR21812CB

Contents

POKESS Front Door Latch Actuator User Manual

Models: 7M2AR21813MC (Front Left), 7M2AR21812CB (Front Right)

1. Important Safety Information

  • WARNING: Keep out of reach of children.
  • In case of ingestion, seek medical attention immediately.
  • Do not disassemble or repair the actuator yourself.
  • Installation must be performed by a qualified technician.
  • Computer programming is required after installation.

2. Product Overview

This product is a direct replacement door latch actuator designed for specific Ford models. It ensures proper locking and unlocking functionality of your vehicle's doors.

POKESS Front Door Latch Actuator with connector detail

Figure 1: POKESS Front Door Latch Actuator with detailed view of the electrical connector.

3. Setup and Installation

3.1 Compatibility Check

Before installation, verify that the actuator is compatible with your vehicle's make, model, and year. Refer to the part numbers below:

  • For Ford Focus
  • For Ford Mondeo
  • For Ford S-max

Specific Part Numbers:

  • 7M2AR21813MC: Front Left Door Latch Actuator
  • 7M2AR21812CB: Front Right Door Latch Actuator

3.2 Pre-Installation Steps

  1. Before replacing the actuator, identify the cause of any warning light illumination related to the door lock system.
  2. Ensure the vehicle's battery is disconnected to prevent electrical shorts or damage during installation.

3.3 Installation Procedure

This door latch actuator is designed for direct replacement of the original vehicle part. However, due to the complexity of vehicle door mechanisms and electrical systems, installation must be performed by a qualified automotive technician.

  1. Carefully remove the door panel and access the existing door latch actuator.
  2. Disconnect the electrical connector and any mechanical linkages from the old actuator.
  3. Remove the old actuator from its mounting points.
  4. Install the new POKESS actuator, ensuring all mounting points are secure.
  5. Reconnect all mechanical linkages and the electrical connector.
  6. Reassemble the door panel.
Close-up of the electrical connector on the door latch actuator

Figure 2: Detailed view of the electrical connector for proper wiring.

3.4 Post-Installation Programming

After physical installation, computer programming is required to integrate the new actuator with your vehicle's electronic control unit (ECU). This step is crucial for proper functionality and should be performed by a qualified technician using appropriate diagnostic tools.

4. Operating Instructions

Once correctly installed and programmed, the POKESS Door Latch Actuator functions identically to the original part. It will respond to your vehicle's central locking system, allowing you to lock and unlock the door via the key fob, interior door lock switch, or manual key.

  • Direct Replacement: Designed for seamless integration.
  • Stable Quality: Provides reliable performance equivalent to OEM parts.

5. Maintenance

The POKESS Door Latch Actuator is a sealed unit and requires no user-level maintenance. It is designed for long-term, reliable operation. For optimal vehicle health, ensure regular vehicle maintenance checks are performed by a qualified service center.

6. Troubleshooting

6.1 Common Issues and Solutions

  • Model Mismatch: If the actuator does not fit or function correctly, verify its compatibility with your specific vehicle model, year, and door position (front left/right). Double-check the part numbers against your vehicle's requirements.
  • Abnormal Operation (e.g., door not locking/unlocking):
    1. Ensure all electrical connections are secure and free from corrosion.
    2. Confirm that the actuator has been properly programmed to the vehicle's ECU. This is a critical step.
    3. Try restarting the vehicle (turn off ignition, wait a few minutes, then restart).
    4. If issues persist, consult with a qualified automotive technician.

7. Specifications

FeatureDescription
Product NameFront Door Latch Actuator
BrandPOKESS
Condition100% Brand New & High Quality
Surface FinishNew
Part Number (Front Left)7M2AR21813MC
Part Number (Front Right)7M2AR21812CB
OEM NO.7M2AR21812CB (example)
OriginMainland China
Package Length25 cm
Package Width22 cm
Package Height9 cm
Package Weight0.753 kg
Side view of the POKESS Door Latch Actuator

Figure 3: Side view of the actuator.

Another angle of the POKESS Door Latch Actuator

Figure 4: Angled view of the actuator.

Rear view of the POKESS Door Latch Actuator

Figure 5: Rear view of the actuator.

8. Warranty and Support

8.1 Warranty Information

This POKESS Door Latch Actuator comes with a 2-year warranty from the date of purchase. This warranty covers manufacturing defects. Please retain your proof of purchase for warranty claims.

8.2 Customer Support

For any questions, technical assistance, or warranty claims, please contact your seller or the POKESS customer support channel where you purchased the product.

For additional detailed information, you may refer to the official user manual PDF: User Manual (PDF)

9. User Tips

  • Verify Compatibility: Always double-check the part numbers and vehicle compatibility (make, model, year, and door position) before purchasing and installing to avoid issues.
  • Professional Installation is Key: Given the critical role of door latch actuators in vehicle safety and security, and the need for computer programming, professional installation is highly recommended.
  • Address Root Causes: If you are replacing an actuator due to a recurring issue, ensure any underlying problems (e.g., wiring issues, water ingress) are resolved to prevent future failures.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.