WESA MZ-01-BM

Contents

WESA MZ-01-BM Series Surface Mount Light Switch & Socket User Manual

Model: MZ-01-BM

1. Introduction

Thank you for choosing the WESA MZ-01-BM series surface mount light switch and socket. This product is designed for reliable performance and ease of installation in various indoor environments. Please read this manual carefully before installation and use to ensure safe and correct operation.

WESA MZ-01-BM Surface Mount Light Switch

Figure 1: WESA MZ-01-BM Surface Mount Light Switch (example unit)

2. Safety Information

  • WARNING: Always turn off power at the main circuit breaker or fuse box before installing, servicing, or removing the device. Failure to do so may result in serious injury or death.
  • Installation should be performed by a qualified electrician or a competent person in accordance with all local and national electrical codes.
  • Do not install in wet locations or areas exposed to direct water spray.
  • Ensure all wire connections are secure and properly insulated.
  • Do not exceed the specified electrical ratings of the device.

3. Setup and Installation

Before beginning, ensure you have the necessary tools: screwdriver (flathead and/or Phillips), wire strippers, and electrical tape.

  1. Turn Off Power: Locate the circuit breaker or fuse that controls the power to the installation area and turn it OFF. Verify power is off using a voltage tester.
  2. Prepare Wires: Strip approximately 10-12mm (0.4-0.5 inches) of insulation from the ends of the electrical wires (Live, Neutral, and Earth if applicable).
  3. Mounting: Position the switch/socket unit on the desired surface. Mark the screw holes. Drill pilot holes if necessary.
  4. Wiring: Connect the wires according to the specific wiring diagram for your unit type (switch or socket). Ensure wires are inserted fully into the terminals and screws are tightened securely.
  5. Secure Unit: Fasten the switch/socket unit to the wall using appropriate screws.
  6. Restore Power: Once installation is complete and all connections are secure, turn the power back ON at the circuit breaker.
  7. Test: Test the functionality of the switch or socket.

For detailed wiring instructions, please refer to the diagrams below and consult the official user manual PDF: View User Manual (PDF)

Wiring Diagrams:

Wiring Diagram for 2 Gang 1 Way Switch

Figure 2: Wiring for 2 Gang 1 Way Switch. Connect Live (L) to the switch input. Connect individual light Live wires (L1, L2, L3) to the respective switch outputs. Neutral (N) connects directly to the lights.

Wiring Diagram for 1 Socket Not Ground

Figure 3: Wiring for 1 Socket (Not Grounded). Connect Live (L) and Neutral (N) wires to the corresponding terminals.

Wiring Diagram for 2 Socket Not Ground

Figure 4: Wiring for 2 Socket (Not Grounded). Connect Live (L) and Neutral (N) wires to the corresponding terminals for both outlets.

4. Operating Instructions

For Light Switches:

Press the button to toggle the connected light fixture(s) ON or OFF. The switch provides a simple mechanical action.

For Sockets:

Insert the plug of your electrical appliance into the socket. Ensure the appliance's voltage and current requirements do not exceed the socket's rating.

5. Maintenance

  • Cleaning: To clean the surface of the switch or socket, wipe gently with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish.
  • Inspection: Periodically inspect the device for any signs of damage, loose connections, or discoloration. If any issues are found, turn off power immediately and consult a qualified electrician.
  • No User-Serviceable Parts: There are no user-serviceable parts inside the unit. Do not attempt to disassemble the device.

6. Troubleshooting

ProblemPossible CauseSolution
Switch does not turn light ON/OFFNo power to the circuit; Loose wiring; Faulty light bulb/fixture; Damaged switch.Check circuit breaker; Turn off power and check wiring connections; Replace light bulb/fixture; If switch is damaged, replace it.
Socket has no powerNo power to the circuit; Loose wiring; Faulty appliance.Check circuit breaker; Turn off power and check wiring connections; Test appliance in another working socket.
Device feels warmOverload; Loose connection.Reduce load on circuit; Turn off power and check wiring connections. If problem persists, consult an electrician.

If you are unable to resolve an issue, please consult a qualified electrician.

7. Specifications

Product Dimensions of WESA MZ-01-BM

Figure 5: Product Dimensions (Front, Back, Side)

FeatureDetail
Brand NameWESA
Model NumberMZ-01-BM
Item TypeSWITCHES (includes sockets)
Switch TypePush Button Switch
Rated Voltage250V~
Rated Current10A (as marked on units); up to 16A (general rating for some switch types)
MaterialPlastic (Flame Retardant)
FeaturesWater transfer coating (Wood EU Standard Spray Plastic)
Is Smart DeviceNo
OriginMainland China
CertificationsRoHS, LVD, CE
Dimensions (approx.)69mm (W) x 69mm (H) x 34mm (D) / 2.71in x 2.71in x 1.33in
Package Dimensions (approx.)7cm (L) x 7cm (W) x 4cm (H)
Package Weight (approx.)0.121 kg

8. User Tips

  • Always ensure the mounting surface is clean and dry before installation for a secure fit.
  • When connecting wires, twist stranded wires tightly before inserting them into terminals to prevent stray strands.
  • For a neat finish, ensure the unit is level before tightening the mounting screws.

9. Warranty and Support

This WESA product comes with a 10-year warranty from the date of purchase, covering defects in materials and workmanship under normal use. This warranty does not cover damage caused by improper installation, misuse, abuse, or unauthorized modifications.

For warranty claims or technical support, please contact your retailer or the manufacturer directly with your proof of purchase.

© 2024 WESA. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.