Introduction
The 8BitDo Lite 2 Bluetooth Gamepad is a versatile and ultra-portable controller designed for a wide range of gaming platforms. This manual provides detailed instructions on how to set up, operate, and maintain your Lite 2 Gamepad, ensuring an optimal gaming experience.
Figure 1: 8BitDo Lite 2 Bluetooth Gamepads (Pink and Turquoise)
Controller Layout
Familiarize yourself with the buttons and indicators on your 8BitDo Lite 2 Gamepad:
- L / R: Left and Right shoulder buttons.
- L2 / R2: Left and Right trigger buttons.
- L3 / R3: Pressable Left and Right analog stick buttons.
- D-pad: Directional Pad.
- -select / +start: Select and Start buttons.
- Home: System Home button.
- Star button: Special function button (e.g., Turbo).
- Mode Switch: Toggles between different connection modes (S for Switch, D for Android).
- Pair Button: For initiating Bluetooth pairing.
- Status LED: Indicates connection status and player number.
- Power LED: Indicates power and charging status.
Figure 2: Multi-platform compatibility overview
Setup
1. Nintendo Switch Connection
Prerequisites: Ensure your Nintendo Switch system and the Lite 2 controller are updated to the latest firmware version. Note that NFC scanning, IR camera, HD rumble, notification LED, and waking up the system wirelessly are not supported. The Status LED can indicate up to 8 players.
Bluetooth Connection (Wireless)
- Turn the mode switch on the controller to the 'S' position.
- Press the Home button to turn on the controller. The LEDs will start to rotate from left to right.
- Press and hold the Pair button for 3 seconds to enter pairing mode. The LEDs will stop blinking for a short moment, then start to rotate again. (This step is only required for the very first time you pair the controller).
- On your Nintendo Switch, go to the Home page, select "Controllers", then click on "Change Grip/Order".
- Wait for the connection. Once successful, the LEDs will become solid, and the controller will vibrate.
Wired Connection
Prerequisites: Ensure that "Pro Controller Wired Communication" is enabled in your Switch's System Settings (System Settings > Controllers and Sensors > Pro Controller Wired Communication).
- Turn the mode switch on the controller to the 'S' position.
- Connect the controller to your Nintendo Switch dock via a USB cable.
- Wait until the controller is successfully recognized by your Switch.
2. Android Device Connection
Prerequisites: Ensure your Android device and the Lite 2 controller are updated to the latest firmware version.
Bluetooth Connection (Wireless)
- Turn the mode switch on the controller to the 'D' position.
- Press the Home button to turn on the controller. LED 1 will start to blink.
- Press and hold the Pair button for 3 seconds to enter pairing mode. The LEDs will stop blinking for a short moment, then start to rotate again. (This step is only required for the very first time you pair the controller).
- On your Android device, go to Bluetooth settings and pair with "8BitDo Lite 2".
- Once connected, the LEDs will become solid, and the controller will vibrate.
Wired Connection
Prerequisites: Your Android device must support OTG (On-The-Go) functionality for wired connection. Please consult your device manufacturer for details.
- Turn the mode switch on the controller to the 'D' position.
- Connect the controller to your Android device via a USB cable.
- Wait until the controller is successfully recognized by your Android device.
Operating Instructions
Turbo Function
- To activate/deactivate Turbo for a button: Hold the desired button, then press the Star button.
- The D-Pad, Left stick, Right stick, Home, Select, and Start buttons cannot be set to Turbo.
- The Turbo function is not available when the controller is in Switch mode.
Motion Control
The 8BitDo Lite 2 features 6-axis motion control, providing an immersive gaming experience. This feature is available when connected to a Nintendo Switch.
Figure 3: 6-axis motion control in use (Switch only)
Vibration
The controller supports vibration feedback for enhanced gameplay, where supported by the game and platform.
Video 1: 8BitDo Lite 2 Gamepad product demonstration, showcasing features like portability, motion control, and vibration.
Maintenance
Battery Information
- The controller has a built-in 480mAh rechargeable battery.
- A full charge takes approximately 1 hour and provides about 20 hours of play time.
- Power LED Indicators:
- Red LED blinks: Low battery.
- Red LED stays solid: Charging.
- Red LED turns off: Fully charged.
- The controller will automatically turn off if there is no connection within 1 minute of being powered on.
- If connected via Bluetooth but inactive, the controller will turn off after 15 minutes.
- The controller remains powered on during a wired connection.
Figure 4: Battery specifications and charging details
Troubleshooting
- Controller not pairing: Ensure the mode switch is set correctly for your device (S for Switch, D for Android). Make sure you are pressing the pair button for 3 seconds. For first-time pairing, this step is crucial.
- Controller not recognized in wired mode: For Switch, verify "Pro Controller Wired Communication" is enabled in system settings. For Android, confirm your device supports OTG. Try a different USB cable or port.
- Input lag or disconnection: Ensure the controller is fully charged. Move closer to your device to avoid interference. Check for firmware updates for both your controller and gaming device.
- Turbo function not working: Remember that the D-Pad, sticks, Home, Select, and Start buttons do not support Turbo. Also, Turbo is not available in Switch mode.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | 8Bitdo |
| Model Number | Lite 2 Bluetooth |
| Interface Type | Bluetooth |
| Type | Gamepads |
| Certification | CE |
| Compatible Platforms | Nintendo Switch, Nintendo Switch 2, Nintendo Switch OLED, Nintendo Switch Lite, Android, iOS, iPadOS, tvOS, macOS, Raspberry Pi |
| Battery Included | Yes |
| Battery Capacity | 480mAh |
| Charging Time | Approx. 1 hour |
| Play Time | Approx. 20 hours |
| D-pad Switch Type | Membrane |
| ABXY Switch Type | Membrane |
| Bumpers Switch Type | Membrane |
| Joystick Sensor Module | K-SLIVER |
| Trigger Button Type | Non-Linear |
| Product Weight | Approx. 82.7g |
| Package Dimensions (L x W x H) | 15cm x 10cm x 5cm |
Figure 5: Lite 2 Gamepad dimensions and weight
User Tips
- The Lite 2 is incredibly lightweight (approx. 82.7g) and thin, making it highly portable. It's designed to be as thin as a card for easy carrying.
- Always ensure your controller and gaming device firmware are up-to-date for the best performance and compatibility.
- When using wired connection with an Android device, confirm that your device supports OTG functionality.
- Take advantage of the 6-axis motion control for a more immersive experience on compatible Nintendo Switch games.
Warranty and Support
For further information, additional support, or to check for firmware updates, please visit the official 8BitDo support website: