FD FD203

Contents

Universal Garage Remote Control FD203 User Manual

Model: FD203

1. Introduction

This manual provides instructions for the setup, operation, and maintenance of your FD203 Universal Garage Remote Control. This remote is designed to duplicate fixed code signals, specifically compatible with DITEC GOL4C systems operating at 433.92MHz. Please read this manual carefully before use to ensure proper functionality and safety.

FD203 Universal Garage Remote Control
Figure 1: FD203 Universal Garage Remote Control, showing four white buttons and a red indicator light. Compatible with Ditec GOL4C fixed code at 433.92MHz.

2. Safety Information

  • Keep the remote control out of reach of children to prevent accidental operation.
  • Do not expose the remote to water or extreme temperatures.
  • Ensure the garage door or gate area is clear before operating to avoid injury or damage.
  • Only use the remote for its intended purpose.

3. Specifications

Attribute Value
Brand Name FD
Model Number FD203
Encoding Method Fixed code
Frequency 433mhz (433.92mhz)
Certification CE
Origin Mainland China
Package Length 10 cm
Package Width 8 cm
Package Height 4 cm
Package Weight 0.046 kg
DITEC GOL4 vs GOL4C compatibility
Figure 2: Compatibility comparison, showing that the FD203 remote is compatible with DITEC GOL4C, but not DITEC GOL4.

4. Setup and Programming

To program your new FD203 remote control, follow these steps carefully. This process involves interacting with your existing garage door or gate receiver unit.

  1. Locate the Receiver: Open the control box of your garage door or gate system and locate the receiver board.
  2. Verify Jumper JR6: Ensure that the jumper labeled 'JR6' on the receiver board is in the 'ON' position.
  3. Activate Programming Mode: Press and hold the black 'PRG' button on the receiver board for approximately 5 seconds.
  4. Program New Remote: While the receiver is in programming mode, press and hold the desired button on your new FD203 remote control for 5 seconds.
  5. Finalize and Test: Wait for 10 seconds for the receiver to reset. After the reset, test the new remote control to ensure it operates the device correctly.

For a visual guide on the programming process, please watch the demonstration video below:

Video 1: Demonstration of the remote control programming process, showing interaction with the receiver unit and the new remote.

5. Operation

Once programmed, operating your FD203 remote control is straightforward:

  • Open/Close: Press the programmed button on the remote control to open or close your garage door or gate.
  • Range: Ensure you are within effective range of the receiver for reliable operation.
  • Indicator Light: The red indicator light on the remote will illuminate when a button is pressed, confirming signal transmission.

6. Maintenance

  • Battery Replacement: If the remote's range decreases or the indicator light dims, it may be time to replace the battery. The remote typically uses a standard coin cell battery (e.g., CR2032). Open the remote casing carefully to access and replace the battery, ensuring correct polarity.
  • Cleaning: Clean the remote with a soft, dry cloth. Do not use abrasive cleaners or immerse it in liquids.
  • Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • Remote not working after programming:
    • Re-check all programming steps carefully.
    • Ensure Jumper JR6 on the receiver board is correctly set to 'ON'.
    • Verify the battery in the remote is fresh and correctly inserted.
    • Confirm your original remote is a DITEC GOL4C fixed code at 433.92MHz. This remote is not compatible with DITEC GOL4 or rolling code systems.
  • Reduced range:
    • Replace the remote's battery.
    • Check for obstructions between the remote and the receiver.
    • Ensure the receiver antenna is not obstructed or damaged.
  • Indicator light not illuminating:
    • Replace the remote's battery.
    • Check for physical damage to the remote.

8. User Tips

  • For best results, perform programming close to the receiver unit.
  • Keep a spare battery on hand for quick replacement.
  • If you have multiple remotes, program them one at a time, following the steps for each.

9. Warranty and Support

For any issues or support, please refer to your purchase documentation or contact the seller. This product is manufactured by Shenzhen Scimagic Development Technology Co.Ltd, located at Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.

A PDF version of this user manual is available for download. Please refer to the product page for the link to the User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.