IRALAN IRALAN Ceiling Fan With Light 52 Inch

Contents

IRALAN Ceiling Fan With Light User Manual

Models: 42-inch and 52-inch Blade Sizes

1. Introduction

Thank you for choosing the IRALAN Ceiling Fan With Light. This manual provides essential information for the safe installation, operation, and maintenance of your new ceiling fan. Please read all instructions carefully before beginning installation and keep this manual for future reference.

IRALAN Ceiling Fan with Light, showing remote and app control

Figure 1: IRALAN Ceiling Fan with Light, highlighting 85-265V input voltage and 30dB quiet operation.

2. Safety Information

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN.

  • To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
  • All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
  • The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet boxes marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less".
  • The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance from the trailing edge of the blades to the floor.
  • Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
  • Do not place objects in the path of the blades.
  • To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
  • Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
  • After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
  • All setscrews must be checked and re-tightened where necessary before installation.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets during assembly or after installation. Do not insert objects in the path of the blades.

WARNING: To reduce the risk of fire or electric shock, this fan is NOT suitable for use with solid-state speed controls.

WARNING: To avoid possible electrical shock, make sure that the electricity is turned off at the main power box before starting work. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.

WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.

WARNING: To reduce the risk of fire, electrical shock or personal injury, ensure that the fan mounting bracket is supported directly from the building structure or the outlet box marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less". Use only the screws provided with the outlet box.

3. Package Contents

Carefully unpack all components and ensure you have all the parts listed below. If any parts are missing or damaged, contact customer support.

Hardware Included

ItemDescriptionQuantity
AABlade attachment screw and fiber washer6
BBTapping Screws4
CCExpansion Bolts2

Fan Components

ItemDescriptionQuantity
AFan-motor assembly1
BLED light kit1
CLamp panel1
DAcrylic sheet1
EInside canopy5
FBlade3
GCanopy1
H10 CM Ball/downrod assembly1
I20 CM Ball/downrod assembly1
JCoupling cover1
KRemote control (Transmitter)1
LRemote control (receiver)1

4. Tools Required

The following tools are required for installation:

  • Phillips screwdriver
  • Flat blade screwdriver
  • Step ladder
  • Drill
  • Wrench

5. Specifications

Your IRALAN Ceiling Fan With Light is designed for optimal performance and quiet operation.

Ceiling fan dimensions and specifications diagram

Figure 2: Detailed dimensions and specifications of the ceiling fan.

FeatureSpecification
Input Voltage85-265V AC
Motor Power30W (DC Brushless Motor)
LED Power18W
Blade Size Options42 inch (105cm) / 52 inch (132cm)
Application Space10-20 M²
Wind Speed Settings6 Gears
Noise LevelAs low as 30-35dB
Light SourceLED (3 color temperatures: 3000K, 4000K, 6000K)
Control MethodRemote Control, APP Control
Body MaterialABS, Aluminum, Copper
Blade MaterialABS
Downrod Lengths10cm / 20cm (two available)
CertificationCE
Turbosilent DC Brushless Motor

Figure 3: Powered by TurboSilent™ DC Brushless Motor for higher performance and 6 wind speeds.

6. Setup and Installation

Before starting, ensure the power is turned off at the circuit breaker. Follow these steps carefully.

6.1 Mounting the Hanger Bracket

For Wooden Ceiling:

  1. Switch off the electrical mains at the circuit breaker fuse box.
  2. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Self Tapping Screws (B) will be drilled.
  3. Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, install the mounting bracket onto wooden ceiling with the 4 Self Tapping Screws (B).

IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG.

For Concrete Ceiling:

  1. Switch off the electrical mains at the circuit breaker fuse box.
  2. Use the Mounting Bracket (A) as a guide, mark the spots where the 2 Expansion Bolts (B) will be drilled.
  3. Remove the Mounting Bracket (A). Drill 2 holes for 8MM diameter and insert 2 Expansion Bolts (B) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (C), Spring Washers (D) and Nuts (E).

IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG.

6.2 Installing the Downrod Assembly

  1. Insert the canopy and the Bolt & Pin cover onto the downrod. Carefully feed motor wires through the downrod assembly.
  2. Slide the ball down the downrod.
  3. Put the round latch in.
  4. Replace the hanger ball at its normal position.
  5. Secure the two screws on the hanger ball.
  6. Thread the suspender through the suspended clock and coupling cover.
  7. Insert the tail of the suspender from the lifting head of the motor.
  8. Remove the lateral pin out from the suspended head position, secure with R type pin (Clevis pin).
  9. Tighten the lifting head screws. Tighten the 2 Set Screws on the Coupling to serve as a clamping force on the Downrod to prevent fan shaking during operation.
  10. Route the Coupling cover, Canopy Ring, Canopy and Hanger Ball through the Downrod in turn, and then install the Lock pin through the hole on the Downrod. Fix it by Screw, then slip down the Coupling Cover in correct position.

6.3 Installing the Remote Control Receiver

  1. Once wiring step has been completed, slide the wired remote receiver in between the mounting bracket and the top of the downrod ball for downrod fans.

6.4 Wiring Diagram

WARNING: Turn off the electric power during installation and making wire connection.

  1. Connect the wire from the ceiling fan into the receiver.
  2. Connect the wire from the receiver with the wire from the house.
Wiring diagram for ceiling fan remote control receiver

Figure 4: Wiring connections for the remote control receiver. (Note: Image is a placeholder, actual wiring diagram from PDF page 9 should be used if available as a separate URL)

(Note: The actual wiring diagram from PDF page 9 shows connections: From CEILING FAN to Receiver, and Receiver to From House (Brown to FOR DC IN L, Blue to FOR DC IN N)).

6.5 Installing the Canopy

  1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
  2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.

6.6 Attaching the Fan Blades

  1. Remove 6 screws from the motor.
  2. Attach the blades to the motor using the removed screws.

6.7 Attaching the Light Kit

CAUTION: To reduce the risk of electric shock, disconnect the electrical circuit to the fan before installing the light fixture.

  1. Remove three screws from the plate on the motor.
  2. Use these three screws to assemble the light kit fitter.
  3. Connect the light source and lock it to the lamp tray with three screws.
  4. Install the acrylic sheet (lamp cover).

7. Operating Instructions

7.1 Remote Control Operation

The remote control allows you to manage all fan and light functions. Ensure the remote control is paired with the fan (refer to pairing instructions in APP control section if needed).

ButtonFunction
① NO/OFFTurns the fan and light ON/OFF.
② Wind speed 1-6 gearAdjusts fan speed from 1 (low) to 6 (high).
③ Increased brightnessIncreases light brightness.
④ Reduced brightnessDecreases light brightness.
⑤ Fan forward/reverse switchChanges fan direction (summer/winter mode).
⑥ General (turn off all functions)Turns off all fan and light functions.
⑦ Turn off the fanCodeSpecific function, possibly for pairing or resetting.
⑧ Increased color temperatureAdjusts light to cooler tones (e.g., 6000K).
⑨ Lower color temperatureAdjusts light to warmer tones (e.g., 3000K).
⑩ Natural WindSimulates natural breeze by varying fan speed.
⑪ 2-hour timeSets a 2-hour timer for fan operation.
⑫ Night lightActivates a dim night light mode.

Note: The remote control must match the same code as the receiver.

7.2 APP Control

Control your fan conveniently from your smartphone.

  1. Step 1: Scan the QR Code provided in the manual (or on the product packaging) to download and install the app on your phone.
  2. Step 2: Turn on the light and search for the light in the app, then pair them.

App Functions:

  • Buttons 1-6 control the power of the fan (fan speed).
  • Adjust color temperature.
  • Power switch for light (lamp on/off) and fan (fan on/off).

Pairing: To pair, turn on the light and press the pairing button in the app immediately.

7.3 Reverse Wind Function (Summer/Winter Mode)

Your fan features a reversible DC motor, allowing you to change airflow direction for seasonal comfort.

Ceiling fan showing summer and winter modes

Figure 5: Reverse the wind without touching the fan. Summer mode (downward airflow) and Winter mode (upward airflow).

  • Summer Mode (Downward Airflow): Creates a cooling breeze.
  • Winter Mode (Upward Airflow): Circulates warm air trapped near the ceiling, helping to distribute heat more evenly.

Use the fan forward/reverse switch (button ⑤ on the remote) to change modes.

7.4 Full Lighting Customization

The integrated LED light offers flexibility to match your environment.

Ceiling fan showing light customization options

Figure 6: Full lighting customization with 3 color temperatures: 3000K, 4000K, 6000K.

  • Select from 3 color temperatures: 3000K (Warm White), 4000K (Neutral White), and 6000K (Cool White).
  • Adjust brightness using the remote control.

8. Maintenance and Care

WARNING: Make sure the power is off before cleaning your fan.

  • Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
  • Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
  • You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
  • You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

9. Troubleshooting

If you experience any issues with your fan, refer to the table below for common problems and solutions.

ProblemSolution
The fan will not start
  • Check the main and branch circuit fuses or breakers.
  • Check the line wire connections to the fan and switch wire connections in the switch housing.
The fan is noisy
  • Ensure all motor housing screws are snug.
  • Ensure the screws that attach the fan blade bracket to the motor hub are tight.
  • Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
  • Allow a 24-hour "breaking in" period. Most noises associated with a new fan disappear during this time.
  • If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
  • Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
  • Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

10. User Tips

  • Voltage Compatibility: The fan supports a wide input voltage range (85-265V), making it suitable for various regions including 240V systems.
  • Light Customization: Remember you can select from 3 color temperatures (3000K, 4000K, 6000K) to suit your mood or activity, from warm relaxation to bright task lighting.
  • Quiet Operation: The fan is designed for ultra-quiet operation (as low as 30-35dB), making it ideal for bedrooms, nurseries, and other quiet spaces where noise can be a disturbance.

11. Warranty and Support

11.1 Warranty Information

To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of "wobble" is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hereby disclaims any and all warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

11.2 Customer Support

For any questions, technical assistance, or warranty claims, please contact us via email:

After-sales email: sxdsltd@163.com

You can also refer to the official user manual PDF for additional details: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.