1. Introduction
This manual provides comprehensive instructions for the setup, operation, and maintenance of your Yinuogo 433.92MHz rolling code gate and garage door remote control. Please read this manual carefully before use to ensure proper functionality and safety.
Video 1: Yinuogo Brand Introduction (Product overview, not an instruction video)
2. Safety Information
- Keep the remote control out of reach of children.
- Do not expose the remote control to water or extreme temperatures.
- Ensure the garage door or gate area is clear before operating to prevent injury or damage.
- Only use the remote control for its intended purpose.
3. Product Overview
The Yinuogo remote control is designed for convenient operation of compatible gate and garage door openers. It features a rolling code encryption method for enhanced security.

Image 1: Yinuogo Remote Control Models 4330E and 4333E with CE Markings

Image 2: Assortment of Yinuogo Remote Controls (Front and Back)

Image 3: Remote Control Compatibility Guide (Note: 4335E and 4335EML are compatible, 84335 is not)
4. Specifications
| Feature | Specification |
|---|---|
| Brand Name | Yinuogo |
| Model Number | YNG106 |
| Frequency | 433.92MHz |
| Encoding Method | Rolling Code |
| Battery | Included |
| Origin | Mainland China |
| Certifications | CE, FCC, RoHS, WEEE |
| Package Dimensions (approx.) | 8cm (L) x 8cm (W) x 8cm (H) |
| Package Weight (approx.) | 0.06 kg |
5. Setup and Programming
To program your new Yinuogo remote control, you will need access to your existing receiver unit, typically located near your garage door or gate motor. The programming process involves pairing the new remote with the receiver.
Programming Steps:
- Locate Your Receiver: Open the housing of your receiver unit, usually found near the garage door or gate motor.
- Identify Programming Button: Find the programming button on the receiver. It is commonly labeled as ENR, MEMO, or PROG.
- Activate Programming Mode: Press the programming button. On some receivers, you may need to hold the button down. The LED indicator on the receiver will illuminate or change state to signal that it has entered programming mode.
- Pair New Remote: While the receiver is in programming mode, press any button on your new Yinuogo remote control for one second, then release it.
- Confirm Programming: The LED on the receiver will either light differently or turn off to indicate successful programming.
- Exit Programming Mode: Wait a few seconds for the receiver to automatically exit programming mode.
Your new remote control is now programmed and ready for use.
6. Operation
Once programmed, operating your Yinuogo remote control is straightforward:
- Press Button: Press the corresponding button on the remote control that you programmed to your gate or garage door opener.
- Observe Action: The gate or garage door should activate (open, close, or stop) as commanded.
- Range: Ensure you are within the operational range of your receiver for reliable performance.

Image 4: Remote Control with Single Button Configuration

Image 5: Remote Control with Three Button Configuration
7. Maintenance
Battery Replacement:
The remote control comes with a battery included. If the remote control's range decreases significantly or it stops responding, the battery may need to be replaced.
- Open Casing: Carefully open the remote control casing. This may involve unscrewing small screws or prying open the case with a small tool.
- Identify Battery: Locate the coin cell battery inside the remote.
- Replace Battery: Remove the old battery and insert a new one of the same type, ensuring correct polarity (+/-).
- Close Casing: Securely close the remote control casing.

Image 6: Internal View of Remote Control (Showing Battery Location)
Cleaning:
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
8. Troubleshooting
- Remote not working after programming: Ensure the programming steps were followed precisely. Some receivers require the programming button to be held down. Verify the receiver's LED indicates successful programming.
- Reduced range: Check the remote control's battery. Replace it if necessary. Ensure there are no obstructions or sources of interference between the remote and the receiver.
- Intermittent operation: This could be due to a low battery, interference, or a loose connection inside the remote. Try replacing the battery first.
- Remote does not match existing remote: Confirm that your existing remote and receiver are compatible with the Yinuogo rolling code system and the 433.92MHz frequency. Refer to Image 3 for compatibility guidance.
9. User Tips
- Build Quality: Users have noted that the build quality of these remotes is superior to some smaller alternatives.
10. Frequently Asked Questions
- Q: What if my receiver does not have an ENR, MEMO, or PROG button?
- A: Consult your receiver's specific manual for its programming method. The labels ENR, MEMO, or PROG are common but not universal.
- Q: Can I program multiple Yinuogo remotes to one receiver?
- A: Typically, yes. Most receivers can store multiple remote codes. Follow the programming steps for each new remote.
- Q: How do I know if my existing remote is compatible?
- A: Check your existing remote or receiver for frequency (should be 433.92MHz) and encoding type (rolling code). Refer to the product images and specifications for compatible models.
11. Warranty and Support
For any issues or further assistance, please refer to the official user manual PDF provided by the manufacturer. You can access the PDF here.
Please retain your proof of purchase for warranty claims. Specific warranty terms and conditions may vary and are detailed in the official documentation.