1. Introduction
The GlintDeer FG-200 DDS Function Signal Generator is a versatile and compact device designed for generating various waveforms across a wide frequency range. It is suitable for electronic circuit testing, debugging, frequency characteristic analysis, and impulse response testing of audio amplifiers. Its DDS (Direct Digital Synthesis) technology ensures good accuracy and frequency stability, making it ideal for oscilloscope sweep time factor calibration. The square wave output is also useful for adjusting oscilloscope attenuators and probe pulse characteristics.

Figure 1: FG-200 DDS Function Signal Generator with included cables and Schumann wave antenna.
2. Specifications
| Parameter | Value |
|---|---|
| Output Waveforms | Sine, Square, Triangle, Forward Sawtooth, Reverse Sawtooth, ECG, Exponential Rise, Exponential Fall, Lorentz Pulse, Gauss Pulse, Sinc Pulse, Half-wave, Full-wave, Schumann Wave, Noise Wave (15 types) |
| Power Supply | DC 4-9V (DC 5V recommended with adapter, 3.7V lithium battery for portable use) |
| Current Consumption | 180mA (at 5V) |
| Frequency Range (Sine Wave) | 0.01Hz - 500.00kHz (amplitude decreases at higher frequencies) |
| Frequency Range (Other Waveforms) | 0.01Hz - 100.00kHz (can be increased if distortion/jitter requirements are not strict) |
| Resolution | 0.01Hz |
| Sine Wave Distortion | <1% (below 1kHz), <0.5% (above 1kHz) |
| Output Amplitude | Max ±10V (P-P) |
| Output Impedance | 50 ohms |
| DC Offset | Max ±10V (with shutdown function) |
| Dimensions | 125mm x 80mm x 26.5mm (approx. 4.92" x 3.15" x 1.04") |
| Certification | CE |
| Battery Included | No |
| High-Concerned Chemical | None |
| DIY Supplies | Electrical |
| Origin | Mainland China |
| Display Size | 3.0 - 4.9 Inches |

Figure 2: Device dimensions.
3. Panel Description

Figure 3: Front Panel Layout.
- MODE: Used to switch the output waveform type.
- CURSOR: Moves the cursor for parameter adjustment (used with '+' and '-' keys).
- RUN/STOP: Starts or stops the waveform output. When the cursor is not blinking, the waveform is output, and other keys are inactive.
- +: Increases frequency or parameter value.
- -: Decreases frequency or parameter value.
- DCOFFSET: DC bias switch. Press ON to enable adjustment of the DC component using the yellow knob. Pop up to OFF to set the DC component to 0.
- FILTER: Filter switch. Activates a filter for cleaner sine waves at frequencies near or above 300kHz. Note that activating the filter may reduce signal amplitude.
- AMP: Side knob to adjust the signal amplitude. Turn clockwise to increase amplitude.
4. Setup and Connections
- Power Supply Connection:
Connect the provided USB to 3.5MM cable to the power input port of the generator. The power source can be a computer USB interface, a mobile phone charging head, or a power bank. It is recommended to use a power supply with 3C certification to ensure proper operation and avoid signal generator malfunctions.

Figure 4: Power and output cables.
- Output Connection (Oscilloscope):
Connect the BNC to alligator clip cable to the DDS OUT terminal. Attach the red alligator clip to the oscilloscope probe and the black alligator clip to the oscilloscope's GND (ground) clip.
5. Operating Instructions
5.1 General Operation Mode
When the generator is in operation mode and the cursor is not flashing (after pressing RUN/STOP), most keys are inactive. To adjust parameters, first press RUN/STOP until the cursor flashes, then use other keys for settings.
5.2 Waveform Selection
Press the MODE key to cycle through and select the desired output waveform. The available waveforms are:
- SIN: Sine waveform
- Lorenz: Lorentz pulse
- Square: Square waveform
- Gaussian: Gaussian pulse
- Triangle: Triangle waveform
- Sinc: Sinc pulse
- Sawtooth: Forward sawtooth wave
- Half-wave: Half-wave
- Resawtooth: Reverse sawtooth waveform
- Full-wave: Full wave
- ECG: Electrocardiogram
- Schumann: Schumann wave
- EXP-rise: Exponential rise
- Noise: Noise wave
- EXP-decay: Exponential decrease
Video 1: Demonstration of waveform selection and parameter adjustment on the FG-200 DDS Function Signal Generator.
5.3 Frequency Adjustment
- Press the CURSOR key to move the flashing cursor to the desired digit of the frequency display.
- Use the + and - keys to adjust the frequency value. The resolution is 0.01Hz.
- Once the desired frequency is set, press RUN/STOP to activate the signal output. The cursor will stop blinking.
Frequency Adjustment Modes:
The device supports two frequency adjustment modes:
- ADC-DEC MODE1: Adjusts the current cursor digit, participating in rounding and debit.
- ADC-DEC MODE2: Adjusts the current cursor digit without rounding up or down.
To switch between modes: Turn off the power. Press and hold the MODE key, then press the power switch. Release the MODE key after approximately 10 seconds. The screen will display "ADD-DEC MODE2" to indicate the change. Repeat these steps to switch back to "ADD-DEC MODE1". Settings are saved automatically.
5.4 DC Bias Adjustment
To output a waveform with a center point of 0 and symmetrical positive and negative values, ensure the DC OFFSET button is popped up (OFF position). If you need to introduce a DC bias, press the DC OFFSET button down (ON position) and then use the yellow knob to adjust the DC component of the signal.
5.5 Waveform Amplitude Adjustment
Adjust the signal amplitude using the AMP knob located on the side of the device. Turn clockwise to increase amplitude and counter-clockwise to decrease it. Adjust until the waveform is not distorted.
5.6 Using Schumann Wave Antennas
To transmit Schumann waves using the dedicated antenna:
- Connect the power supply and press the POWER switch.
- Press MODE to select "Wave: Schumann".
- Ensure the DC OFFSET switch is popped up (OFF position).
- Adjust the side AMP amplitude knob to the center position.

Figure 5: Schumann Wave Antenna.

Figure 6: Signal generator connected to Schumann wave antenna.
6. Maintenance
- Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
- Do not use abrasive cleaners or solvents, as these may damage the casing or display.
- Store the device in a safe place when not in use to prevent physical damage.
7. Troubleshooting
- Q: The signal generator is not powering on or working correctly.
- A: Ensure you are using a stable power supply, preferably one with 3C certification. Poor quality power supplies can cause malfunctions. Check all cable connections.
- Q: The output amplitude decreases at higher frequencies for sine waves.
- A: This is a known characteristic of the device for sine waves above 500kHz. For other waveforms, the amplitude may also be affected above 100kHz if distortion and jitter requirements are strict.
- Q: The waveform appears distorted or noisy.
- A:
- Check the power supply for stability.
- For sine waves near or above 300kHz, try activating the FILTER switch. Note that this may slightly reduce amplitude.
- Adjust the AMP knob to ensure the amplitude is not set too high, causing clipping.
8. User Tips
- When adjusting parameters, remember to press RUN/STOP first to make the cursor flash, enabling parameter changes.
- For precise frequency adjustments, experiment with both ADC-DEC MODE1 and ADC-DEC MODE2 to see which suits your needs better. The device saves your last selected mode.
- If you need to output a clean signal without any DC component, always ensure the DC OFFSET switch is in the OFF (popped up) position.
9. Warranty and Support
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For technical support, troubleshooting assistance, or warranty claims, please contact the seller or manufacturer directly. Please retain your proof of purchase for warranty validation.