ZUOYA LS02

Contents

ZUOYA LS02 Mechanical Keyboard Kit User Manual

Model: LS02

Introduction

Thank you for choosing the ZUOYA LS02 Mechanical Keyboard Kit. This kit features a hot-swappable design, gasket structure, RGB backlighting, and versatile connectivity options including wired USB, 2.4G wireless, and Bluetooth. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your keyboard.

ZUOYA LS02 Gaming Mechanical Keyboard Kit overview
Figure 1: ZUOYA LS02 Gaming Mechanical Keyboard Kit overview, highlighting Gasket Structure, Three linking methods, and RGB backlight.

Package Contents

The ZUOYA LS02 Mechanical Keyboard Kit typically includes:

  • ZUOYA LS02 Keyboard Base (barebones)
  • USB Type-C Cable
  • 2.4G Wireless Receiver
  • User Manual (this document)

Note: Switches and keycaps are not included and must be purchased separately.

ZUOYA LS02 Mechanical Keyboard Kit barebones
Figure 2: ZUOYA LS02 Mechanical Keyboard Kit (barebones) showing the PCB and hot-swap sockets.

Setup Instructions

1. Installing Switches and Keycaps

  1. Ensure the keyboard is powered off or disconnected.
  2. Align the pins of your 3-pin or 5-pin mechanical switches with the hot-swap sockets on the PCB.
  3. Gently press each switch until it clicks into place. Do not force switches to avoid bending pins.
  4. Once all switches are installed, attach your desired keycaps to the switch stems.

2. Connection Modes

The ZUOYA LS02 supports three connection methods: Wired USB, Bluetooth, and 2.4G Wireless. Use the switch on the back of the keyboard to select the desired mode.

Feature icons for ZUOYA LS02 keyboard
Figure 3: Key features of the ZUOYA LS02, including three connection methods and 3/5 pin switch support.

2.1. Wired Mode Setup

  1. Locate the mode switch on the back of the keyboard and set it to the "OFF" position (Wired mode).
  2. Connect the USB Type-C end of the cable to the keyboard and the USB-A end to your computer.
  3. The top-left indicator light will show red for 5 seconds, indicating a successful wired connection.

2.2. Bluetooth Mode Setup

  1. Set the mode switch on the back of the keyboard to "BT" (Bluetooth mode). The top-left indicator light will turn blue.
  2. Press and hold Fn + 1, Fn + 2, or Fn + 3 for 3 seconds to enter pairing mode for one of the three Bluetooth channels. The top-left indicator light will flash rapidly.
  3. On your computer or device, search for Bluetooth devices and select "ZUOYA LS02" to connect.
  4. Once connected, the top-left indicator light will change from flashing red to a flowing RGB effect, indicating successful pairing.
  5. To clear Bluetooth pairing records, press and hold Fn + 0 for 2 seconds.

2.3. 2.4G Wireless Mode Setup

  1. Set the mode switch on the back of the keyboard to "2.4G" (2.4G Wireless mode). The top-left indicator light will turn green.
  2. Plug the 2.4G USB receiver into an available USB port on your computer.
  3. Press and hold Fn + 4 for 3 seconds to enter 2.4G pairing mode.
  4. The indicator light will change from flashing red to a flowing RGB effect, indicating successful pairing.

3. Re-pairing (Forced Pairing)

3.1. Bluetooth Re-pairing

In Bluetooth mode, press and hold Fn + 1/2/3 (for the desired channel) for 3 seconds. The top-left indicator light will flash rapidly for 2 minutes, indicating it's in pairing mode.

3.2. 2.4G Wireless Re-pairing

In 2.4G mode, press and hold Fn + 4 for 3 seconds. The top-left indicator light will flash rapidly for 20 seconds, indicating it's in pairing mode.

Operating Instructions

1. Keyboard Functions (FN Combinations)

CombinationFunction
Fn + 1/2/3 (Hold 3s)Bluetooth Pairing (Channels 1, 2, 3)
Fn + 0 (Hold 2s)Clear Bluetooth Pairing Records
Fn + 4 (Hold 3s)2.4G Wireless Pairing
Fn + ZSwitch to macOS System Layout
Fn + XSwitch to Windows System Layout
Fn + WinLock/Unlock Windows Key
Fn + ESC (Hold 3s)Restore Factory Settings
Fn + F1My Computer
Fn + F2Search
Fn + F3Calculator
Fn + F4Media Player
Fn + F5Previous Track
Fn + F6Next Track
Fn + F7Play/Pause
Fn + F8Stop
Fn + F9Mute
Fn + F10Volume Down
Fn + F11Volume Up
Fn + F12Email
Fn + ←Toggle Right Indicator Light Bar On/Off
Fn + ↑Increase Main Key Area Backlight Brightness
Fn + ↓Decrease Main Key Area Backlight Brightness
Fn + →Switch Main Key Area LED Direction (Right)
Fn + DelSwitch Main Key Area LED Direction (Left)
Fn + HomeIncrease Main Key Area Backlight Speed
Fn + EndDecrease Main Key Area Backlight Speed
Fn + PgUpSwitch Main Key Area Single Color Light
Fn + PgDnToggle Full Keyboard Lock/Unlock

2. Multimedia Knob Function

The knob located on the top right of the keyboard has dual functions:

  • Default Function: Volume Control
    • Rotate clockwise: Increase volume (+)
    • Rotate counter-clockwise: Decrease volume (-)
    • Press down: Mute/Unmute (ON/OFF)
  • Alternative Function: Backlight Effect Control
    • Rotate clockwise: Next backlight effect (+)
    • Rotate counter-clockwise: Previous backlight effect (-)
    • Press down: Toggle backlight ON/OFF

To switch between Volume Control and Backlight Effect Control: Press and hold the knob down for 3 seconds. The top-left red indicator light will flash once to confirm the function switch.

3. RGB Backlight Control

The ZUOYA LS02 features dynamic RGB backlighting with multiple modes and colors.

RGB backlit ZUOYA LS02 keyboard
Figure 4: ZUOYA LS02 keyboard with RGB backlighting enabled.
  • Switching Effects: Use the multimedia knob (when set to backlight control) to cycle through 18 different lighting effects. The keyboard has power-off memory for the last selected effect.
  • Default Effect: "Flowing Wave" (随波逐流).
  • Available Effects: Light off, Steady on, Breathing, Snake Run, Neon Gradient, Snow Trace, Flowing Horse, Wavy, Starry, Galloping, Flowing Wave, Great Roc Spreading Wings, Walking in the Rain, Winding Path, Water Ripple, etc.
  • Brightness and Speed: Adjust using Fn key combinations (see table above).

4. Right Indicator Light Bar

The light bar on the bottom right serves multiple purposes:

  • Toggle On/Off: Press Fn + ←.
  • Connection Status:
    • Bluetooth: Red light during pairing, solid blue after successful pairing/reconnection.
    • 2.4G: Red light during pairing, solid green after successful pairing/reconnection.
    • Note: After indicating status, it returns to the default flowing light effect.
  • Caps Lock Indicator: White light for 5 seconds when Caps Lock is on (turns off immediately if switched back to lowercase).
  • Full Keyboard Lock Indicator: Red light for 5 seconds when full keyboard lock is active.
  • Win Key Lock Indicator: White light for 5 seconds when Win key is locked.
  • Low Voltage Alarm: Red light flashes continuously until the main key area backlight goes to sleep. If any key is pressed, it flashes again. The keyboard will shut down when the battery is critically low.
  • Sleep Mode: After 6 minutes of inactivity, the main key area LEDs and the right indicator light bar will turn off. Press any key to wake up the keyboard and restore lighting. The indicator light bar sleeps in sync with the main key area.

5. Charging Instructions

The ZUOYA LS02 has a built-in 4000mAh rechargeable lithium battery.

4000mAh rechargeable battery
Figure 5: The ZUOYA LS02 features a built-in 4000mAh rechargeable lithium battery.

The RGB light under the spacebar acts as the charging indicator:

  • Wired Mode Charging: Solid red light. Turns solid green when fully charged.
  • Wireless Mode Charging: Green light flashes for 5 seconds, then returns to the RGB backlight mode.

Maintenance

To ensure the longevity and optimal performance of your ZUOYA LS02 keyboard, follow these maintenance tips:

  • Cleaning: Regularly clean the keyboard with a soft, dry cloth. For dust and debris between keycaps, use compressed air. For stubborn stains, slightly dampen a cloth with water or a mild electronics cleaner (ensure the keyboard is powered off and disconnected).
  • Storage: Store the keyboard in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Avoid dropping the keyboard or exposing it to liquids. Do not attempt to disassemble the keyboard beyond switch and keycap removal, as this may void the warranty.

Troubleshooting

1. Keyboard Not Responding

  • Wired Mode: Ensure the USB cable is securely connected to both the keyboard and the computer. Try a different USB port or cable.
  • Wireless Modes (Bluetooth/2.4G):
    • Check if the keyboard is powered on and the correct mode (BT/2.4G) is selected.
    • Ensure the keyboard is charged.
    • Try re-pairing the keyboard (see "Re-pairing" section).
    • For 2.4G, ensure the receiver is properly plugged in.
    • For Bluetooth, ensure Bluetooth is enabled on your device and try removing and re-adding the keyboard from your device's Bluetooth settings.

2. Backlight Not Working or Incorrect

  • Check if the backlight is turned off (e.g., by pressing the knob if set to backlight control).
  • Adjust brightness using Fn + ↑/↓.
  • Cycle through backlight modes using the multimedia knob.
  • Ensure the keyboard is not in sleep mode.

3. Keys Not Registering or Double-Typing

  • Ensure switches are fully seated in their sockets.
  • If a specific switch is faulty, it can be hot-swapped with a new one.
  • Try restoring factory settings (Fn + ESC for 3 seconds).

4. Low Battery Issues

  • If the right indicator light bar flashes red, the battery is low. Connect the keyboard via USB to charge it.
  • The keyboard will eventually shut down if the battery is critically low.

Specifications

FeatureDescription
ModelLS02
Product NameTri-mode Mechanical Keyboard
Dimensions330 x 150 x 40mm ±5mm
Wired InterfaceUSB Type-C (USB 1.1/2.0 compatible, supports USB 3.0)
Wired Working Voltage5.0V ±0.25V
Wireless Working Voltage3.3V - 4.2V
Wired Working Current<300mA
Wireless Working Current<350mA
Hot-swappable SwitchesYes (3-pin/5-pin)
Backlight TypeMULTICOLOR (RGB)
Operation StyleMechanical
LanguageEnglish
Keyboard Standard82 Key
ApplicationDesktop, Laptop, Tablet
TypeBluetooth Wireless
Battery Capacity4000mAh
System RequirementsWindows (full functionality), macOS (standard key functions, special function keys not supported)
ZUOYA LS02 Product Structure Diagram
Figure 6: Exploded view of the ZUOYA LS02 product structure, showing layers like upper cover, positioning plate, EVA cotton, IXPE switch pad, circuit board, sponge, and bottom shell.

User Tips

  • RGB Control: To quickly turn off the RGB backlight, use the multimedia knob (if set to backlight control) by pressing it down, or cycle through effects until "Light off" is selected.
  • Customizing Backlight: While direct color selection for individual keys might not be available through hardware, the keyboard offers 18 distinct lighting effects to personalize your experience.
  • Battery Life: To maximize battery life in wireless modes, consider turning off the backlight when not needed, especially when the keyboard is idle.

Warranty and Support

Thank you for your trust and support in our products. To ensure your peace of mind and protect your rights, we strictly adhere to relevant regulations for after-sales service:

  • Warranty Period: 12 months from the date of purchase.
  • Service Content: Services will be provided in accordance with regulations for repair, replacement, and return of microcomputer products.

Warranty Exclusions:

The warranty does not cover the following conditions:

  • Exceeding the valid service period or free warranty period.
  • Malfunctions or damage caused by improper use, maintenance, or storage not in accordance with instructions.
  • Malfunctions or damage caused by repairs performed by unauthorized service providers.
  • Product defects due to force majeure (e.g., natural disasters).
  • Product defects caused by human factors (e.g., operational errors, bumps, inputting incorrect voltage).
  • Other malfunctions or damages not attributable to product design, technology, manufacturing, or quality issues.

Warranty Card:

Please retain your proof of purchase and fill out the warranty card for future service needs.

Warranty Card Details:

Product Model: LS02

Purchase Date: ____________________

Customer Name: ____________________

Contact Phone: ____________________

Contact Address: ____________________

Inspector: PASS

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.