1. Introduction
This manual provides detailed instructions for the installation, operation, and configuration of your Wenzhi ZigBee/WiFi MmWave Radar Human Body Presence Motion Sensor. This advanced sensor is designed for smart home applications, offering precise human presence and motion detection, along with luminosity sensing and an integrated relay for light switch control. It supports both ZigBee and WiFi connectivity for integration with Tuya Smart Life and other compatible smart home systems.
For a comprehensive guide, you may also refer to the official user manual PDF: Wenzhi Human Presence Sensor User Manual (PDF).
2. Safety Information
WARNING: Electrical Shock Hazard
- Always disconnect power at the circuit breaker before installing or servicing the device.
- Do not remove the cover with power connected.
- Installation should be performed by a qualified electrician or in accordance with local electrical codes.
- Ensure the input voltage (AC85-265V) matches your electrical system.
- This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
- Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
3. Package Contents
Verify that all items are included in your package:
- Wenzhi Human Presence Sensor
- User Manual (this document and/or PDF)
- Mounting Screws and Wall Plugs
- 3M Adhesive Pad
4. Specifications
| Parameter | Description |
|---|---|
| Model Number | WZ75 Series (e.g., MTG035-ZB-RL, MTG036-WF-RL, MTG235-ZB-RL, MTG236-WF-RL, MTG075-ZB-RL, MTG275-ZB-RL, MTG076-WF-RL, MTG276-WF-RL) |
| Brand Name | wenzhi |
| Certification | CE, RoHS |
| Origin | Mainland China |
| Size (24GHz) | Ø75mm*61mm (2.95inch*2.4inch) |
| Size (5.8GHz) | Ø105mm*28mm (4.13inch*1.1inch) |
| Weight | Approx. 120g |
| Detection Angle | 110°x110° (or 115°x115°/120°x120° depending on model) |
| Detection Range | 0-10m (Default 6m) |
| Ceiling Detection Radius (24GHz) | Presence: 2.5-3m, Motion: 4-5.5m |
| Ceiling Detection Radius (5.8GHz) | Presence: 2-3m, Motion: 4-4.5m |
| Sensor Sensitivity | 0-9 (Default 7) |
| Ceiling Installation Height | Typical 2.7-3.5m |
| Departure Delay | 0.5s-1500s (Default 15s) |
| Luminosity (Beam) | 0-500 Lux |
| System Frequency | 5.8 GHz ±75 MHz ISM wave, 24GHz ±125 MHz ISM wave |
| Transmitting Power | 3-5 dBm (5.8GHz), 10dBm (24GHz) |
| Network | ZigBee3.0 / WiFi (2.4GHz) / BLE |
| Input Voltage | AC85-265V |
| Power Consumption | <2W |
| Working Temperature | -10°C to +50°C |
| Storage Temperature | -20°C to +65°C |
| Working Humidity | 5-90% RH (No Condensation) |
| Working Altitude | 0-3500m (or 0-2000m depending on model) |
| Relay Load | Resistive loads 1000W (or 3000W), LED ≤300W |
5. Installation
The sensor is designed for ceiling or wall mounting. Ensure the installation location is free from major interference sources (see Troubleshooting section).
5.1. Detection Range: Ceiling Mounted
The sensor detects micro movements, general movements, and presence/breath. The detection area varies based on installation height and sensitivity settings.
5.2. Installation Method
The sensor can be installed using expansion screws or self-adhesive pads.
- Preparation: Unscrew the panel counter-clockwise to open the back cover.
- Mounting:
- Using Expansion Screws: Drill 6mm holes (H35mm/0.24inch H1.38inch) with a spacing of 60mm (2.36inch). Insert wall plugs and secure the sensor with screws.
- Using Self-Adhesive: Apply the adhesive to the back of the product and stick it to the ceiling or wall of the area that needs to be detected.
- Wiring: Connect the necessary wires (see Section 6).
- Final Step: After connecting to the network, cover the panel by screwing it clockwise.
5.3. Installation Principles
- In hallways, changing rooms, kitchens, and other indoor areas, sensors should be installed in the center as much as possible and firmly fixed.
- In bathrooms and toilets, sensors should be installed 0.4-0.6m in front of the top of the toilet/squatting position, away from doors, windows, and exhaust fans.
- For living rooms/dining rooms/conference rooms, locate 0.5-1m in front of the sofa, directly above the table.
- For bedrooms and studies, directly above the bed, within 0.6-1.5 meters behind the table.
- For glass and gypsum board partitions, install the sensor as close to the solid wall as possible. If it's all glass and gypsum board, install in the center and adjust Detection Range, Entry Distance Indentation, and Entry Sensitivity.
- For sitting, squatting, and standing still scenes, ceiling mounted sensors should be 0.4m in front of the head top to 0.8m position. Avoid installing directly overhead.
- For dense deployment scenarios, the linear spacing distance between sensors should not be less than 5m.
6. Wiring Diagram
The sensor requires AC85-265V input. Connect the Live (L) and Neutral (N) wires. If you are connecting an optional light or appliance, use the 'OUT' terminal for the switched load.
Note: If the sensor is used only for detection and not to control a load, only the L and N wires need to be connected.
7. Connecting to the Network & App Operation
7.1. App Installation
Search for "Tuya Smart" or "Smart Life" in your app store (Google Play Store or Apple App Store) and download it. Alternatively, scan the QR code below for direct download. After installation, register and log in to the app.
7.2. Network Connection
- After the sensor is powered on for the first time or if it's not connected to the network, the red and blue lights will light up for approximately 2.5 seconds and then turn off for 2 seconds. The sensor will automatically enter a continuous network connection state for 2 minutes.
- When the sensor enters network connection mode, the blue indicator light flashes quickly (0.5 seconds per time).
- If connecting to the network fails, power cycle the device or press and hold the connect to network button for more than 3 seconds to re-enter the connected network state.
- Open the Smart Life/Tuya app, tap the "+" symbol in the upper right corner, and select "Add Device".
- Wait for the app to discover the device and tap "Add". After successful addition, the device's blue indicator light remains on for 10 seconds and then turns off.
7.3. ZigBee2MQTT Integration (Advanced Users)
Update ZigBee2MQTT to the latest version. If issues persist, refer to the provided GitHub link for specific instructions and JS files: wzwenzhi/Werzhi-ZigBeeZmult. When using ZigBee2MQTT, it is recommended to set the "Distance report mode" to "occupation detection" to reduce information reporting.
8. Parameter Settings
The sensor's behavior can be fine-tuned through various parameters in the Smart Life/Tuya app.
8.1. Common Parameter Settings
- Sensitivity (0-9, Default 7): Adjusts the detection threshold for the strength of object energy.
- Departure Delay (0.5s-1500s, Default 15s): Configures the confirmation time after the target disappears. A larger value reduces false positives from accidental disappearances.
- Detection Range (0-10m, Default 6m): Sets the maximum distance the sensor will detect.
- Entry Sensitivity (0-9, Default 7): Threshold for initial target entry, used to filter out accidental contact interference.
- Entry Filter Time (0-5s, Default 0.1s): Filters accidental contact interference when a target enters the detection range.
- Entry Distance Indentation (0-10.00m, Default 0.6m): Indents the detection distance inward to avoid false triggering from distance edge interference.
- Shield Range (0-10.00m, Default 0m): Sets the nearest distance the sensor will detect. Must be less than the Detection Range.
- Block Time (0.1-255.0s, Default 2.5s): After switching from occupied to unoccupied, this is the time before the sensor can detect a target again. Helps resolve interference from power ripple and radiation.
8.2. Control Parameter Settings
- Status Indication (Silence/Instructions, Default Silence):
- Silence: Indicator light will not flash when human presence is detected.
- Instructions: Indicator light will flash when human presence is detected.
- Sensor (Default Turn On): The radar sensor can be set to four states: Turn On, Turn Off, Manned (Occupied), and Unmanned (Unoccupied). For example, if set to Manned, it will maintain a presence state regardless of actual presence.
- Breaker Mode (Standard/Local/Mandatory/Not Support):
- Standard (Cloud Linkage): The relay can be remotely controlled via the APP.
- Local (Automatic): If presence is detected, the relay automatically turns on; otherwise, it turns off.
- Not Support: Disables the relay. The device functions only as a sensor.
- Breaker Status (Turn On/Turn Off): In Standard mode, the relay can be remotely controlled via the APP.
- Illumin Threshold (0-500.00 Lux): When in Local (Automatic) mode, the relay can be controlled in conjunction with the illumin threshold. If the actual luminance is below the threshold, the local mode operates normally. If the luminance exceeds the threshold, the relay remains closed regardless of presence.
9. Operating Modes (Relay/Breaker)
The sensor offers flexible control over its integrated relay, allowing it to function as a smart switch based on presence detection and luminosity.
- Standard (Cloud Linkage): In this mode, the relay's on/off state is controlled remotely through the Tuya Smart Life app. This allows for complex automations and integrations with other smart home devices.
- Local (Automatic): This mode enables autonomous operation. If human presence is detected, the relay will automatically turn on. When presence is no longer detected (after the Departure Delay), the relay will automatically turn off. This mode is ideal for automatic lighting or fan control.
- Not Support (Sensor Only): In this mode, the relay function is disabled. The device acts solely as a presence and luminosity sensor, reporting data to the app or smart home hub without directly controlling any connected load.
10. Common Interference Sources & Solutions
To ensure optimal performance, be aware of potential interference sources and apply the recommended solutions:
- Fan: Change the position of the fan or sensor. The fan should not appear in the presence detection area.
- Air Conditioning: Ensure the air swing and louver vibration of the air conditioning are outside the sensor's presence detection area.
- Rolling Shutter with Aluminum Alloy Lower Rail: Set an appropriate detection range to filter out such interferences.
- Exhaust Fan: Avoid the presence of exhaust fans or vibration surfaces within the sensor detection distance range. Fix the exhaust fan to avoid causing ceiling vibration.
- Strong 5.8GHz WiFi Signal Interference: It is recommended to install the WiFi router at least 3m away from the sensor in the front area. For routers in other directions, maintain a distance of at least 1.5m. When using a top-mounted AP, maintain a distance of at least 1.5m between the AP and the sensor.
- Air Flow (Wind): Set appropriate sensitivity.
- Animals: Setting appropriate sensitivity and Entry Distance Indentation can help avoid false triggers.
- Low Frequency Vibration: Avoid direct exposure of radar signals to sound and other vibration sources. Set a relatively low sensitivity (to avoid false triggering) and use a longer Entry Filter Time.
FCC Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference, try reorienting or relocating the receiving antenna, increasing separation between equipment and receiver, or connecting the equipment to a different circuit. Consult a dealer or an experienced radio/TV technician for help.
11. User Tips
- Calibration is Key: Take the time to adjust the sensor's parameters (sensitivity, detection range, departure delay) in the app to match your specific environment and desired behavior. Proper calibration can significantly improve performance and prevent ghosting or missed detections.
- Home Assistant Integration: Many users report seamless integration with Home Assistant via ZHA or Zigbee2MQTT. Ensure your Home Assistant setup is up-to-date for the best experience.
- Safety First: For added safety, especially with 220V wiring, consider using an additional fine fuse (e.g., 0.2A, 220V) in your circuit.
- Version 2 Features: If you have a V2 sensor, leverage its improved lux sensor, built-in relay, and appliance input for more versatile smart home automations.
- Wi-Fi vs. ZigBee: While both versions are effective, some users find the ZigBee version to be more accurate and responsive for presence detection.
12. Frequently Asked Questions (FAQ)
- Q: How do I set the sensor to automatically turn on a light when motion is detected and turn it off when no motion is detected?
- A: This functionality is achieved using the "Local (Automatic)" Breaker Mode. In the app's parameter settings, navigate to "Control Parameter Settings" and set "Breaker Mode" to "Local (Automatic)". Ensure your light is correctly wired to the sensor's OUT terminal. You can also adjust the "Departure Delay" to control how long the light stays on after presence is no longer detected.
- Q: What is the ideal installation height for wall mounting?
- A: While the manual primarily details ceiling installation (typical height 2.7-3.5m), for wall mounting, consider the detection range and angle. Position the sensor to cover the desired area without obstructions. Experiment with the "Detection Range" and "Entry Sensitivity" settings in the app to optimize performance for your specific wall-mounted location.
- Q: Does the sensor integrate with Alexa, and what is the latency?
- A: Yes, since the sensor integrates with Tuya Smart Life, it generally supports integration with Amazon Alexa. You can link your Tuya Smart Life account to Alexa to create routines. The latency for detection and relay activation is not explicitly stated in milliseconds but is influenced by the "Departure Delay" setting (0.5s-1500s) and your network's responsiveness. For ZigBee versions, local control can offer lower latency compared to cloud-dependent Wi-Fi versions.
13. Warranty and Support
For specific warranty information, please refer to the terms provided by your retailer or the official Wenzhi website. If you encounter any issues or require technical assistance, please contact the seller or Wenzhi customer support directly.
You can also refer to the comprehensive user manual PDF for additional details and troubleshooting steps: Wenzhi Human Presence Sensor User Manual (PDF).