1. Introduction
Thank you for purchasing the TOPPING E30 II Lite high-performance DAC. This manual will guide you through the setup, operation, and maintenance of your device to ensure you get the best audio experience.
1.1 Package Contents
- TOPPING E30 II Lite Unit x1
- DC Cable x1
- USB Cable x1
- Remote Control x1
- User Manual x1
- Warranty Card x1
Note: Drivers and the latest version of the user manual can be downloaded from the official TOPPING website.
2. Product Overview
2.1 Front Panel
- LED Screen: Displays current input channel, sampling rate (in DAC mode), or volume level (in PRE mode).
- Remote Control Receiver: For receiving signals from the included remote control.
- Multifunction Touch Button: Used for power on/off, standby, input switching, and menu navigation.
2.2 Rear Panel

Rear panel showing input and output connections.
- RCA Output (L/R): Single-ended stereo analog audio output for connecting to an amplifier or active speakers.
- Coaxial SPDIF Input: Digital audio input.
- Optical SPDIF Input: Digital audio input.
- USB Input: For connecting to a computer or other USB audio source.
- Power Input (DC5V/1A): Connect the provided DC power cable.
3. Setup
3.1 Power Connection
- Connect the provided DC cable to the DC5V/1A Power Input on the rear panel of the E30 II Lite.
- Plug the other end of the DC cable into a suitable power source.
3.2 Audio Output Connection
- Connect RCA cables from the RCA Output (L/R) on the E30 II Lite to the corresponding analog audio inputs on your amplifier, pre-amplifier, or active speakers.
3.3 Audio Input Connection
Connect your audio source device to one of the following inputs:
- USB Input: Use the provided USB cable to connect your computer, smartphone (with OTG adapter), or other USB audio source.
- Optical SPDIF Input: Use an optical cable to connect devices like CD players, game consoles, or TVs.
- Coaxial SPDIF Input: Use a coaxial cable to connect devices like CD players or digital audio transports.
3.4 USB Driver Installation (for Windows)
For Windows operating systems, a specific USB driver may be required for optimal performance. Please visit the official TOPPING website (www.topping.audio) to download and install the latest driver for the E30 II Lite before connecting it to your computer.
4. Operating Instructions
4.1 Power On/Off and Standby
- Power On: The E30 II Lite enters standby mode automatically when connected to power. The screen will display a bright dot.
- Enter/Exit Standby: When the unit is working, press and hold the front multifunction touch button, or press the Standby button on the remote control, to enter standby. Short press the front button or the remote's Standby button to exit standby.
- Automatic Standby: If the current input is not connected or the input signal is invalid for 1 minute, the unit will automatically enter standby. It will automatically resume working state once a valid signal is detected.
4.2 Volume Control
- Mute: Press the Mute button on the remote control to mute the audio output. Press it again or adjust the volume to exit mute state.
- Adjusting Volume: In PRE (Pre-amplifier) mode, use the Volume Up (+) and Volume Down (-) buttons on the remote control to adjust the output volume. Pressing and holding these buttons will quickly adjust the volume.
- Note: In DAC mode, the volume is fixed at 0dB and is not adjustable.
4.3 Input Channel Switching
Press the front multifunction touch button or the Input Switch (Left/Right) buttons on the remote control to cycle through the available input channels (USB, Optical, Coaxial).
4.4 Remote Control Functions
The remote control provides convenient access to various functions:
- Mute: Mutes/unmutes audio output.
- Standby: Enters/exits standby mode.
- Volume Up (+)/Down (-): Adjusts volume in PRE mode.
- Input Switch (Left/Right Arrows): Cycles through input channels.
- OK Button: Confirms selections in the setup menu.
- Filter Setting: Accesses PCM and DSD filter settings.
- Brightness: Adjusts screen brightness.
4.5 Setup Menu
The setup menu allows you to customize various settings of your E30 II Lite.
4.5.1 Entering the Setup Menu
While the unit is in standby mode, press and hold the front multifunction touch button for 5 seconds to enter the setup menu.
4.5.2 Navigating and Saving Settings
- Using Front Panel: Press the touch button to move to the next setting item. Double-press to change parameters. Press and hold until
