TOPPING E1x2 OTG

Contents

Topping E1x2 OTG Professional Audio Interface

User Manual

Model: E1x2 OTG (TPP30D)

1. Introduction

Thank you for purchasing the Topping E1x2 OTG Professional Audio Interface. This device is designed for high-quality audio input and output, suitable for live streaming, recording, and general audio production. It features ultra-linear mic premodules, multiple OS support, zero-latency monitoring, and high sample rate support (192kHz/24Bit). Please read this manual thoroughly to ensure proper setup and operation.

Topping E1x2 OTG Professional Audio Interface front view

Figure 1: Topping E1x2 OTG Audio Interface

2. Package Contents

Please check the box for the following items:

  • E1x2 OTG Host Unit
  • USB-A to USB-C Data Cable
  • USB-C to USB-C Data Cable
  • 6.35mm to 3.5mm Adapter
  • Quick Start Guide

3. Product Overview: Parts and Names

Familiarize yourself with the controls and connectors on your E1x2 OTG.

Topping E1x2 OTG front and rear panel diagram with labels

Figure 2: Front and Rear Panel Layout

3.1. Front Panel

  1. IN (Combo Input): For connecting microphones (XLR), instruments (6.35mm TS), or line-level devices (6.35mm TRS).
  2. INST (Instrument/Line Switch): Toggles input impedance and gain for instrument or line-level signals. Light off for Line, light on for Instrument.
  3. 48V (Phantom Power): Activates 48V phantom power for XLR microphone inputs. Caution: Only use with condenser microphones that require it. Ensure all volume levels are minimum before switching.
  4. Input Gain Knob: Adjusts the gain level for the IN input. Monitor LED meters to avoid clipping (red CLIP light).
  5. MON (Direct Monitor Switch): Enables zero-latency direct monitoring of input signals to headphone output.
  6. LED Meters: Displays input (IN1) and output (OUT1&2) signal levels. Red CLIP light indicates clipping.
  7. Power Indicator: Solid light (working), off (power off), breathing (standby).
  8. OTG Indicator: Solid light (OTG device connected), off (no device).
  9. Monitor Mix Knob: Balances live input signals and computer playback in the headphone mix (when MON is active).
  10. Headphone Volume Control: Adjusts the volume of the headphone output.
  11. 6.35mm Headphone Output Jack: Connect your headphones here.
  12. GAIN (Headphone Amp Gain): Sets headphone amplifier gain (low when off, high when on).
  13. MONITOR (Line Out Volume): Adjusts the output level sent to LINE OUT.

3.2. Rear Panel

  1. LINE OUT: 6.35mm TRS balanced jacks for connecting to active speakers or amplifiers.
  2. OTG: Connect mobile devices for audio recording or playback.
  3. USB-C: Connects to a computer for data transmission and power.
  4. POWER (DC5V Input): Connect an external DC5V power supply if the USB-C port (16) cannot provide sufficient power, especially with mobile devices. When external power is used, USB-C (16) is for data only.
  5. Power Switch: Turns the unit on/off.

3.3. Factory Reset

To restore factory settings, press and hold the MON button (5) on the front panel while powering on the device until all LED meters light up.

4. Setup and Connections

Before connecting or disconnecting any devices, ensure all volume levels on the E1x2 OTG are set to minimum to prevent damage to your hearing or equipment.

Topping E1x2 OTG connection diagram showing microphone, headphones, speakers, and computer

Figure 3: Connection Diagram

4.1. Basic Connections

  • Microphone/Instrument: Connect your microphone (XLR) or instrument (6.35mm TS) to the IN combo jack (1).
  • Headphones: Connect your headphones to the 6.35mm Headphone Output Jack (11).
  • Monitors/Speakers: Connect your active studio monitors or amplifier to the LINE OUT jacks (14) on the rear panel.
  • Computer/Mobile Device: Connect the E1x2 OTG to your computer or mobile device using the appropriate USB-C cable to the USB-C port (16).
  • External Power (Optional): If needed, connect a DC5V power supply to the POWER port (17).

4.2. USB Interface Mode Setting

The E1x2 OTG supports both PC and Mobile device modes. The mode determines how the device interacts with your connected computer or phone/tablet.

  1. Power on the E1x2 OTG.
  2. Press and hold the 48V button (3) on the front panel to enter setup mode.
  3. Press the 48V button again to switch between modes:
    • PC Mode: Indicated by 8 LED meters lighting up.
    • Mobile Mode: Indicated by 4 LED meters lighting up.
  4. Power off and reboot the device to save the selected mode.

5. Operating Instructions

5.1. TOPPING Professional Control Center

For advanced settings and control, download the TOPPING Professional Control Center software from the official Topping website. Refer to the detailed reference guide available on their website for software usage: TOPPING Professional Control Reference Guide.

5.2. Digital Audio Workstation (DAW) Setup

The E1x2 OTG is compatible with any DAW that supports Core Audio (Mac) or ASIO (Windows).

  1. Open your DAW's preferences or settings.
  2. Navigate to the Audio/MIDI or Playback Engine section.
  3. Select

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.